Installation Guide

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
P/N 0301683 Rev. A 05/2013
English
Single-Pole:
Insulated wires
connected to two
screws of the same
color. See Step 5a
when wiring.
OR
3-Way:
Insulated wires connected to three
screws. One of these wires is connected
to a screw of a different color (not green)
or labeled COMMON. MARK or TAG this
wire to identify it when wiring. See Step
5b when wiring.
Tag
Different-colored screw
(Common). Actual location may vary.
OR
Ground
(Bare Copper
or Green Wire)
Ground (Bare Copper
or Green Wire)
Installation
1
Turn OFF Power.
• Turn power OFF at circuit break er or remove fuse.
2
Removing Wallplate and Switch.
• Remove wallplate and switch mounting screws.
• Carefully remove switch from wall (do not remove wires).
WARNING: Shock Hazard. May result in
serious injury or death. Turn off power
at circuit breaker before installing
the unit.
3
Identifying the Type of Circuit.
4
Disconnecting Switch Wires.
Lutron Technical Support Center 1.800.523.9466 24 hrs / 7 days www.lutron.com
Important Note: Your wall switch may have two wires attached to
the same screw (see illustrations below for examples). Tape these
two wires together before disconnecting. Connect both wires to the
control wire in Step 5.
One wire in the backwired
hole and one to the screw.
Looped Wire:
Turn screw to loosen.
Screw Terminals:
Turn screws to loosen.
Push-in Terminals:
Insert screwdriver. Pull wire out.
OR
OR
For installations involving more than one control in wallbox,
refer to Multi-Unit Installations before beginning.
AYFSQ-F
CTFSQ-F
DLFSQ-F
DVFSQ-F
DVSCFSQ-F
DVWFSQ-F
LGFSQ-F
LXFSQ-F
TGFSQ-F
120 V~ 60 Hz 1.5 A
Models:
DVFSQ-F-HO
DVSCFSQ-F-HO
LXFSQ-F-HO
120 V~ 60 Hz 2 A
Models:
Technical Assistance
If you have questions concerning the installation or operation of this product, call the
Lutron Technical Support Center. Please provide exact model number when calling.
U.S.A. and Canada (24 hrs/7days)
1.800.523.9466
Mexico
+1.888.235.2910
Other countries 8am – 8pm ET
+1.610.282.3800
Fax [phone]
www.lutron.com
Limited Warranty (Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after
purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA
18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF
MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST
OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE
FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL
DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CON NEC TION WITH THE
MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PUR CHASE
PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do
not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty
may last, so the above limitations may not apply to you.
Lutron Claro and Fassada are registered trademarks of Lutron Electronics Co., Inc.
NEC is a registered trademark of National Fire Protection Association, Quincy, Massachusetts.
© 2013 Lutron Electronics Co., Inc.
Break Off Side Sections
Each Control Has Inside
Sections Removed
Middle Control Has Two
Side Sections Removed
Important Notes: Please read before installing.
1. CAUTION: To avoid overheating and possible damage to other equipment, do not use to control
receptacles, lighting, fluorescent lighting fixtures, or transformer-supplied appliances.
2. Do not use control with a fan and light that operate with the same switch.
3. When no “grounding means” exists within the wallbox for an existing control, the 2011 National
Electrical Code® (NEC®) allows a control to be installed as a replacement as long as 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected
by a ground fault circuit interrupter. The 2008 NEC® has the same allowances but does not contain
the requirement for nonmetallic attachment screws. When installing a control according to any of
these methods, cap or remove the green wire before screwing the control into the wallbox.
4. Wiring controls in a circuit which contains a ground fault circuit interrupter (GFCI) or an arc fault circuit
interrupter (AFCI) may cause nuisance tripping and is not recommended.
5. Use control with a ceiling paddle fan only. Use only one ceiling paddle fan per control.
6. For new installations, wire a test switch before installing the control.
7. Set multi-speed fans to their highest setting before installing controls.
8. Use only one control in a 3-way circuit.
9. Install in accordance with all national and local electrical codes.
10. Clean control with a soft damp cloth only. Do not use any chemical cleaners.
Multi-Unit Installations
When combining controls in one wallbox,
remove all inner side sections before wiring
(see at right). Use pliers to bend each side
section up and down until it breaks off.
Reduction of control capacity is not required.
Single Pole/3-Way
Quiet Fan-Speed Controls
7
Turn ON Power.
Turn ON power at circuit break er or replace fuse.
6
Mounting Control to Wallbox.
• Form wires carefully into the wallbox, mount and align control.
• Install faceplate.
• Note: Only one control can be used in a 3-way
circuit. Control can be used in either location.
• Connect the green ground wire on the control
to the bare copper or green ground wire in the
wallbox. (See Important Note 3.)
• Connect black control wire to the tagged wire
removed from the switch. If you had taped
together two wires (see step 4), connect both
wires to the black control wire screw and
remove the tape
• Connect the red wire on the control to one of the
remaining wires removed from the switch.
• Connect the red/white wire on the control to the
remaining wire removed from the switch.
• Connect the green ground wire on the control
to the bare copper or green ground wire in the
wallbox. (See Important Note 3.)
• Connect the black control wire to one of the
wires removed from the switch. If you had taped
together two wires (see step4), connect both
wires to the black control wire and remove
the tape.
• Connect the red wire on the control to the other
wire removed from the switch.
• Cap off the red/white wire on the control. Do
NOT connect to any other wire or ground.
5
5a - Single-Pole Wiring
5b - 3-Way Wiring
OR
Green
Ground
Red
Red /
White
Black
Ground
Red
Red /
White
Black
Tag
120 V~
60 Hz
Live Black
Red
Red/White
Green
Ground
Neutral
Fan
Control
Red
Red/White
Green
Ground
Ground
Fan
Neutral
3-Way
Switch
Control
Note: Depending on model number, the control may include a Lutron®
Claro® or Fassada® wallplate.
A Lutron® wallplate consists of 2 parts, a faceplate (front) that snaps into
an adapter plate (back).
Please detach faceplate from adapter plate before installing. This will
expose control mounting holes and prevent faceplate
damage during installation.
Grasp top
of faceplate
and pull
forward to
detach it
from adapter
plate.
Faceplate (Front)
Adapter plate (Back)
• Note: Control can be installed in either
location.
Attach standard wallplate.
Attach ClaroR or FassadaR wallplate which consists of 2 parts, an
adapter plate (back) and faceplate (front).
OR
Faceplate
(Front)
Adapter plate
(Back)
Note: Do not
overtighten
mounting screws.
Permanent damage
may occur.
Snap on faceplate
Note: Follow recommended strip lengths and combinations for supplied wire
connectors. Wire connectors are suitable for copper wire only. For aluminum
wire, consult an electrician.
Twist wire
connector tight.
Ensure that no
bare wire is
exposed.
Wiring the Control.
• For installations involving more than one control in a wallbox, refer to the section on
Multi-Unit Installations before beginning.
120 V~
60 Hz
Live Black
Green
0301683
0301683
• Easy-to-follow
Instructions
• Instrucciones
fáciles de seguir
• Instructions
faciles à suivre
• Easy-to-follow
Instructions
• Instrucciones
fáciles de seguir
• Instructions
faciles à suivre
®
®
0301683
0301683
• Easy-to-follow
Instructions
• Instrucciones
fáciles de seguir
• Instructions
faciles à suivre
• Easy-to-follow
Instructions
• Instrucciones
fáciles de seguir
• Instructions
faciles à suivre
®
®
Do Not Remove
Outside Sections