Cut Sheet

ManualsBrandsLutron ManualsGRAFIK EyeDimmer Interface; GRAFIK Eye, Black

Table Of Contents

SPECIFICATION SUBMITTAL Page

Job Name:

Job Number:

Model Numbers:

Lutron GRX-TVI Power Interfaces

369247e 1 07.07.16

GRX-TVI Ten Volt Interface

Features

• 100-277 V~ forward, reverse, and center phase control

input capability

• Provides 0—10 V- control and switching capabilities to

switch and dim current sourcing ﬂuorescent ballasts and

LED drivers.

• Switches and dims current sourcing 0—10 V-

electronic dimming ballasts / drivers powered by

100—277 V~. Switches up to 16 A of electronic

capacitive ballasts / drivers.

• Switches motors up to 1/2 HP @ 100-120 V~,

1 ½ HP @ 200—277 V~ and 5 A @ 230 V~ CE.

• Up to ﬁve Ten Volt Interfaces may be connected to one

Control Unit zone. This allows one zone to control up to

ﬁve 16 A circuits of Electronic Dimming Ballasts / Drivers

or ﬁve motors (This is not true for C5-BMJ-16A).

• Provides 100—277 V~ power to loads.

• Requires 100—277 V~ power for internal operations.

Compatible Controls

Family Product

Wiring

Diagram

Residential Systems HW-RPM-4U I, J

HW-RPM-4A I, J

HWI-WPM-6D

(Wallbox Power Module)

A, B

HxD-6ND C, D

HWV-FDB-8A E, F

Rx-6ND * C, D

RRD-10ND * C, D

GRX-IA A, B

RRD-6NA * C, D

HQRD-6NA * C, D

HWD-5NE * C, D

Commercial Systems LP-RPM-4U I, J

LP-RPM-4A I, J

GRAFIK Eye

Control Unit

3000 Series or

QSG

A, B

GP Panels K, L

C5-BMJ-16A ** M, N

Family Product

Wiring

Diagram

Wallbox Fluorescent

3-wire Dimmers

AYF-103P E, F

DVF-103P E, F

DVSCF-103P E, F

LXF-103PL E, F

MAF-6AM ** G, H

MRF2-F6AN-DV G, H

MSCF-6AM ** G, H

NF-10 E, F

NF-103P E, F

NTF-10 E, F

NTF-103P E, F

SF-10P E, F

SF-103P E, F

VF-10 E, F

VTF-6AM G, H

MRF2-6ELV-120 * C, D

* The low end trim should be set at 28% and the high end trim at

81% manually to have the output signal set to ﬂuorescent load

type.

** These speciﬁc controls result in the GRX-TVI not conforming

to the IEC929 standard for 0—10 V- output since they cannot

reach the 1 V- minimum.

All models in this column are set to ﬂuorescent load type except

those model numbers followed by a *.

Note: 277 V~ operation on the control terminal was a design

feature added September 2013. To check whether your TVI has

this feature, please ensure the front label of the TVI shows the

acceptable voltage range as 100—277 V~ for the control input.

Prior revisions of the unit had (2) L2/H2 terminals (one for 120 V~

and one for 240 V~). The current design of the unit accepts a

universal voltage (100—277 V~), so either of these terminals can

be used for the control feed. They are internally tied together.

Summary of content (18 pages)

PAGE 1
Lutron GRX-TVI Power Interfaces 369247e 1 07.07.16 GRX-TVI Ten Volt Interface Features • 100-277 V~ forward, reverse, and center phase control input capability • Provides 0—10 V- control and switching capabilities to switch and dim current sourcing ﬂuorescent ballasts and LED drivers. • Switches and dims current sourcing 0—10 Velectronic dimming ballasts / drivers powered by 100—277 V~. Switches up to 16 A of electronic capacitive ballasts / drivers.
PAGE 2
Lutron GRX-TVI Power Interfaces 369247e 2 07.07.16 Speciﬁcations Regulatory Approvals • • • • cUL® Listed in US and Canada CE NOM (Mexico) Complies with requirements for use in other spaces used for environmental air (plenums) per NEC® 2014 300.
PAGE 3
Lutron GRX-TVI Power Interfaces 369247e 3 07.07.16 Dimensions and Mounting • Mount only where ambient temperature is 32 °F to 104 °F (0 °C to 40 °C) • Allow 4.5 in (114 mm) between Interfaces when mounting several in a vertical layout • Mount so that line (mains) voltage wiring is at least 6 ft (1.8 m) from sound or electronic equipment and associated wiring • Mount within 7° of true vertical Front View (cover closed) Side View 4.
PAGE 4
Lutron GRX-TVI Power Interfaces 369247e 4 07.07.16 Wiring Diagrams • Each terminal can accept up to two 12 AWG (2.5 mm2) conductors. • L1 / H1 is the Line / Hot feed to power the load. • L2 / H2 (on the control circuit terminals) supplies operating power for the Ten Volt Interface. • Wiring Diagrams A, C, E, G, I, and M show a GRX-TVI wired from one distribution panel.
PAGE 5
Lutron GRX-TVI Power Interfaces 369247e 5 07.07.16 Wiring Diagrams (continued) Wiring Diagram B: HomeWorksR Wallbox Power Module / GRAFIK EyeR Control Unit — 2 Distribution Panels / 2 Feeds GRX-TVI HomeWorksR Wallbox Power Module 1 (HWI-WPM-6D) L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI. Use the appropriate voltage in the range of 100—277 V~.
PAGE 6
Lutron GRX-TVI Power Interfaces 369247e 6 07.07.16 Wiring Diagrams (continued) Wiring Diagram C: HomeWorks® MaestroR / RadioRAR / RadioRA® 2 Dimmers — 1 Distribution Panel / 1 Feed GRX-TVI NOTICE: 0—10 V- Control Signal Wires — DO NOT CONNECT TO LINE VOLTAGE. LutronR is not liable for damage due to miswiring. Note: Dimmer must be wired on the load side of the Remote Dimmer. Remote Dimmer1 Brass L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally.
PAGE 7
Lutron GRX-TVI Power Interfaces 369247e 7 07.07.16 Wiring Diagrams (continued) Wiring Diagram D: HomeWorks® MaestroR / RadioRAR / RadioRAR 2 Dimmers — 2 Distribution Panels / 2 Feeds GRX-TVI Note: Dimmer must be wired on the load side of the Remote Dimmer. Remote Dimmer1 L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Use any voltage in the range of 100—277 V~. L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally.
PAGE 8
Lutron GRX-TVI Power Interfaces 369247e 8 07.07.16 Wiring Diagrams (continued) Wiring Diagram E: AriadniR / DivaR / LyneoR / SkylarkR / NovaR / Nova T R / VareoR 3-wire Fluorescent Dimmers — 1 Distribution Panel / 1 Feed GRX-TVI L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Shown in picture as the same voltage as L2 / H2. L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally.
PAGE 9
Lutron GRX-TVI Power Interfaces 369247e 9 07.07.16 Wiring Diagrams (continued) Wiring Diagram F: AriadniR / DivaR / LyneoR / SkylarkR / NovaR / Nova T R / VareoR 3-wire Fluorescent Dimmers — 2 Distribution Panels / 2 Feeds GRX-TVI L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Use any voltage in the range of 100—277 V~.
PAGE 10
Lutron GRX-TVI Power Interfaces 369247e 10 07.07.16 Wiring Diagrams (continued) Wiring Diagram G: MaestroR / ViertiR 3-wire Fluorescent Dimmers — 1 Distribution Panel / 1 Feed GRX-TVI Companion Dimmer 1 L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Shown in picture as the same voltage as L2 / H2. L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI.
PAGE 11
Lutron GRX-TVI Power Interfaces 369247e 11 07.07.16 Wiring Diagrams (continued) Wiring Diagram H: MaestroR / ViertiR 3-wire Fluorescent Dimmers — 2 Distribution Panels / 2 Feeds GRX-TVI L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Use any voltage in the range of 100—277 V~. L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI.
PAGE 12
Lutron GRX-TVI Power Interfaces 369247e 12 07.07.16 Wiring Diagrams (continued) Wiring Diagram I: HomeWorks® Remote Power Module / LP Module — 1 Distribution Panel / 1 Feed GRX-TVI RPM / LP Module 1 Terminal Blocks L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Shown in picture as the same voltage as L2 / H2. L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI.
PAGE 13
Lutron GRX-TVI Power Interfaces 369247e 13 07.07.16 Wiring Diagrams (continued) Wiring Diagram J: HomeWorks® Remote Power Module / LP Module — 2 Distribution Panels / 2 Feeds GRX-TVI RPM / LP Module 1 Terminal Blocks L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Use any voltage in the range of 100—277 V~. L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI.
PAGE 14
Lutron GRX-TVI Power Interfaces 369247e 14 07.07.16 Wiring Diagrams (continued) Wiring Diagram K: GP Panel — 1 Distribution Panel / 1 Feed GRX-TVI L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Shown in picture as the same voltage as L2 / H2 L2/H2 100-277 V~ L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI. Use the appropriate voltage in the range of 100—277 V~.
PAGE 15
Lutron GRX-TVI Power Interfaces 369247e 15 07.07.16 Wiring Diagram L: GP Panel — 2 Distribution Panels / 2 Feeds GRX-TVI L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI. Use the appropriate voltage in the range of 100—277 V~. Refer to the Note on the ﬁrst page of the GRX-TVI Speciﬁcation Submittal. L2/H2 100-277 V~ L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load.
PAGE 16
Lutron GRX-TVI Power Interfaces 369247e 16 07.07.16 Wiring Diagram M: EcoSystemR Dimming Power Module for 3-wire LutronR Dimming Ballast / drivers — 1 Distribution Panel / 1 Feed L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI. Use the appropriate voltage in the range of 100—277 V~. Refer to the Note on the ﬁrst page of the GRX-TVI Speciﬁcation Submittal.
PAGE 17
Lutron GRX-TVI Power Interfaces 369247e 17 07.07.16 Wiring Diagram N: EcoSystemR Dimming Power Module for 3-wire LutronR Dimming Ballast / drivers — 2 Distribution Panels / 2 Feeds L2 / H2 terminals are tied to each other internally. It is the Line / Hot feed that powers the internal circuitry of the GRX-TVI. Use the appropriate voltage in the range of 100—277 V~. Refer to the Note on the ﬁrst page of the GRX-TVI Speciﬁcation Submittal.
PAGE 18
Lutron GRX-TVI Power Interfaces 369247e 18 07.07.16 Wiring Diagram O: 1 Distribution Panel with 2 Separate Feeds GRX-TVI L1 / H1 is the Line / Hot feed that powers the Switched Line / Hot output to the load. Use any voltage in the range of 100—277 V~. Shown in picture as the same voltage as L2 / H2. NOTICE: 0—10 V- Control Signal Wires — DO NOT CONNECT TO LINE VOLTAGE. LutronR is not liable for damage due to miswiring. 0—10 VBallast / Driver 1 Note: Dimmer must be wired on the load side.