Installation Manual

Wiring Diagrams
Wiring Diagram 5
Live Black
Red
Yellow
Green or Bare
Ground
Fan
Light
Neutral
Control
120 V~
60 Hz
Wiring Diagram 6
Live
Black
or Blue
Cap off second Blue
(if present)
Green or
Bare
Ground
White
Dimmer
Yellow
Red
Orange
Black
White
To Additional Ballasts
Neutral
120 or 277 V~
60 Hz
(depending
on model)
Orange
Black
White
Dimming Ballast
Dimming Ballast
Wiring Diagram 1
Live Black
Control
Ground
Green or Bare
Load
Neutral
Black
120 V~
60 Hz
Wiring Diagram 2
Live
Red
Dimmer
Ground
Green or Bare
Load
Neutral
Black
120 V~
60 Hz
Red
Wiring Diagram 7
Live
Blue
Green or
Bare
Ground
Ground
White
Blue
Dimmer
Yellow
Red
Orange
Black
White
To Additional Ballasts
Neutral
277 V~
60 Hz
Orange
Black
White
Dimming Ballast
Dimming Ballast
3-Way
Switch
Wiring Diagram 9
Live
Blue
Green or
Bare
Ground
Ground
White
Blue
Dimmer
Yellow Black
White
To Additional Ballasts
Neutral
277 V~
60 Hz
Black
White
Dimming Ballast
Dimming Ballast
3-Way
Switch
Wiring Diagram 3
NOTE: Dimmers may be wired on either the line side
or the load side of the switch.
= Indicates different
colored screw
Live Black
Dimmer
Red
Red
Ground
3-Way
Switch
Ground
Load
Neutral
Green or Bare
120 V~
60 Hz
Wiring Diagram 8
120 or 277 V~
60 Hz
(depending on
model)
Black Yellow or Red
Dimmer
Green
White
Neutral
Live
Load
Ground
= Indicates different
colored screw
Wiring Diagram 4
NOTE: Dimmers may be wired on either the line side
or the load side of the switch(es).
Live
Black
Red
Red
Green or
Bare
Ground
Dimmer
4-Way
switch
3-Way
Switch
Load
Neutral
Ground
Ground
120 V~
60 Hz
Model
Number(s)
Control
Type
Voltage/
Rating
Wiring
Diagram
Approved Load(s)
Incandescent/
Halogen
Magnetic
Low-Voltage
Electronic
Low-Voltage
Solid-State
Fan
Ceiling Paddle
Fan
Lutron® 3-wire
fluorescent
ballasts or LED
drivers
Advance® Mark X® Series
Electronic Fluorescent
Dimming Ballasts
NT-600
NT-1000
NT-1500
NT-2000
Incandescent
Dimmers
120 V~
60 Hz
1 X
NT-1PS
NT-3PS
NT-4PS
Incandescent
Switches
120 V~
60 Hz
1 X
NT-603P
NT-1003P
NT-1503P
Incandescent
Dimmers
120 V~
60 Hz
2 (single pole)
3 (3-way)
4 (4-way)
X
NTLV-600
NTLV-1000
NTLV-1500
Magnetic
Low-Voltage
Dimmers
120 V~
60 Hz
1 X X
NTLV-603P
NTLV-1003P
NTLV-1503P
Magnetic
Low-Voltage
Dimmers
120 V~
60 Hz
2 (single pole)
3 (3-way)
4 (4-way)
X X
NTLV-600-277
NTLV-1000-277
Magnetic
Low-Voltage
Dimmers
277 V~
60 Hz
8 X X
NTELV-300
NTELV-600
Electronic
Low-Voltage
Dimmers
120 V~
60 Hz
8 X X
NTFS-6E
NTFS-12E
Fan-Speed
Controls
120 V~
60 Hz
5 X
NTFSQ
Quiet
Fan-Speed
Control
120 V~
60 Hz
1.5 A
1 X
NTF-10
Fluorescent
Dimmers
120 V~
60 Hz
6 X
NTFTU-5A
Fluorescent
Dimmers
120 V~
60 Hz
1 X
NTF-10-277
Fluorescent
Dimmer
277 V~
60 Hz
6 X
NTF-103P
Fluorescent
Dimmer
120 V~
60 Hz
8 A
6 X
NTF-103P-277
Fluorescent
Dimmer
277 V~
60 Hz
6 A
6 (single pole)
7 (3-way)
X
NTFTU-5A-277
Fluorescent
Dimmer
277 V~
60 Hz
5 A
8 X
NTFTU-3AP-277
(contact
customer service
for availability)
Fluorescent
Dimmer
277 V~
60 Hz
3 A
9 X
Notes
• Magneticlow-voltagedimmers:Formoreinformtaion,seeApplicationNote19:“GuidetoDimmingLow-VoltageLighting,”P/N048019,atwww.lutron.com.Operation
of a dimmed low-voltage circuit with all lamps removed or inoperative may result in current ow in excess of normal levels. To avoid possible transformer failure, Lutron
strongly recommends the following: Do not operate dimmed low-voltage circuits without operative lamps in place; replace burned-out bulbs immediately; and use
transformers that incorporate thermal protection or fused transformer primary windings in order to prevent transformer failure caused by excess current.
• Electroniclow-voltagedimmers:Thesedimmersareoverload-protected.Ifmorethantheratedloadisapplied,powertothecircuitwillshutoffuntilthedimmercools.If
this happens, remove excess load from the circuit.
• Fan-Speedcontrols:Usewithfansmarked“Suitableforusewithsolid-statefan-speedcontrolsonly.”Setmulti-speedfanstotheirhighestsettingbeforeinstallingcontrols.
• Quietfan-Speedcontrols:DonotwireintoacircuitwithaGFCIbreakerorreceptacle.Setmulti-speedfanstotheirhighestsettingbeforeinstallingcontrols.Not
recommended for use with Hunter Original Series fans; contact Lutron Customer Service department for suitable controls.
• ForLEDloads,pleaseseethe“ReportCards”atwww.lutron.com/hilumeledforproperloadingofthedimmer.