Installation Guide

x3
Hold for 6 seconds
until LED starts
blinking
Supported Loads (120 V~)
Using your Caséta Wireless kit (sold separately)
1
Press and hold “off” button on the switch
2
Press and hold “off” button on remote
Pairing the switch and
Pico remote control
Go to www.casetawireless.com/support for
additional troubleshooting suggestions.
Symptoms Probable cause and action
Light does not
turn on or in-wall
switch LED does
not light up.
• Red and black wires on the
switch are reversed. (See
steps 4.2 and 4.3 on the
previous page)
• Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS on the switch is in the
Off position.
Light does not
respond to Pico
remote control.
• The switch failed to pair with
Pico remote control; see Pairing
the switch and Pico remote
control.
• The switch is already at the light
level the Pico remote control is
sending.
• The Pico remote control is
outside the 30 ft (9 m) operating
range.
• The Pico remote control battery
is low.
• The Pico remote control battery
is installed incorrectly.
For advanced features, tips for using Caséta Wireless products with LEDs, the complete Caséta Wireless product line,
and more, please visit www.casetawireless.com/features
Replacing light bulbs using FASS
Pull the FASS out on the in-wall switch to remove
power at the light socket.
Lutron,
Lutron, Caséta, and Pico are trademarks of Lutron Electronics
Co., Inc., registered in the U.S. and other countries. FASS and
Lutron
are
trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark
of the National Fire Protection Association, Quincy, Massachusetts.
Google and the Google logo are registered trademarks of Google Inc.,
used with permission.
© 2014–2017 Lutron Electronics Co., Inc
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Troubleshooting
Hold for 6 seconds
until lights flash 3 times.
Device Ratings
In-wall switch
PD-5ANS, PD-6ANS
120 V~ 50/60 Hz
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Repeat steps to pair other Pico remote controls.
Pico remote control (sold separately)
On
Off
FASS
™
Front Accessible
Service Switch
In-wall switch
With a smartphone or tablet (Smart Bridge required, sold separately)
1 Press and hold “off” button on dimmer
2
Press and hold “off” button on remote
The Lutron app will walk you through
setting up your devices.
Download the Lutron app
www.casetawireless.com/LutronApp
Launch the Lutron app
The Caséta Wireless switch can be controlled from a smartphone
when used with the Lutron Smart Bridge. All devices must be within
30 ft (9 m) from the Lutron Smart Bridge.
If you are using the switch and remote control with the Lutron
Smart Bridge follow the instructions below.
Search for “Lutron Caseta”
3
Press and hold “off” button on remote
Use the Lutron app to complete ALL remaining steps
Lutron
Lutron Smart Bridge
Note: If you are using the switch and remote control with
another manufacturer’s bridge, please refer to that manufacturer’s
instructions for set-up.
Lutron
Lutron app
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.
Without a smartphone or tablet
(Smart Bridge not required)
Control
three ways
Add devices
• Pico remote controls
• Dimmers
• Shades
Schedule
your lights
Connect
while away
LED—up to 5 A
Incandescent / Halogen—up to 600 W
MLV—up to 600 VA
ELV—up to 600 W
Fluorescent—up to 5 A
General Purpose Fan—up to 3 A
Using your controls
On
Off
Lutron
PD-5ANS
LED—up to 6 A
Incandescent / Halogen—up to 720 W
MLV—up to 720 VA
ELV—up to 720 W
Fluorescent—up to 6 A
General Purpose Fan—up to 3.6 A
PD-6ANS