Installation Guide

Troubleshooting
Using your dimmer
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Replacing light bulbs using FASS
Pull the FASS switch out on the in-wall dimmer to
remove power at the light socket.
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
On
Slider
Off
• Adjust slider to dim / brighten
the light level
• Will not turn lights off
FASS
Front Accessible
Service Switch
Pico paddle remote
Dimmer
On
Off
)Lutron, Lutron, Claro, Caséta, Pico, the Caseta logo, the design of the Diva
dimmer, Diva and FASS are trademarks or registered trademarks of Lutron
Electronics Co., Inc. in the US and/or other countries.
All other product names, logos, and brands are property of their respective owners.
© 2023 Lutron Electronics Co., Inc.
Slider
FASS
Front Accessible
Service Switch
Dimmer
On
Off
1. Pull the Front Accessible Service Switch (FASS) out to
the open position.
2. Press and HOLD the
Off
button.
3. Continue to HOLD the
Off
button and push the FASS in
until the light bar flashes.
4. Release the
Off
button and adjust the slider to desired
low-end brightness.
5. Press
Off
to save settings.
Light bar
Go to www.casetawireless.com/support for additional troubleshooting suggestions.
Symptoms Probable cause and action
Light does not turn on or the dimmer light bar does not light up. • Light bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS switch on the dimmer is in the Off position.
Light does not respond to Pico remote. • The dimmer failed to pair with Pico remote; see Pairing the dimmer and Pico paddle remote.
• The dimmer is already at the light level the Pico remote is sending.
• The Pico remote is outside the 30 ft (9 m) operating range.
• The Pico remote battery is low.
• The Pico remote battery is installed incorrectly.
• Bulbs turn off while being dimmed.
• Bulbs turn on at high light level but do not turn on at a low light level.
• Bulbs flicker or flash when dimmed to a low light level.
Verify bulbs are marked dimmable and see the Adjusting low-end trim section for information on adjusting the dimmer for
best bulb performance.
Load is Off and the light bar blinks 4 times, pauses, and repeats. The dimmer is in Over Temperature Protection (OTP) mode.
• See Ganging and Derating. Ensure the dimmer is not overloaded.
• Reset the dimmer by using the Front Accessible Service Switch (FASS); See Using your dimmer section. Pull out the FASS and
push it back in.
Device Ratings
In-wall dimmer
DVRF-6L
120 V~ 50/60 Hz
Pico paddle remote
PJ2-P2B
3 V- 10 mA
(1) CR2032 battery (included)
CAUTION
Use only with permanently installed fixtures with dimmable
LED, dimmable CFL, halogen, or incandescent lamps. To
avoid overheating and possible damage to other equipment,
do not use to control receptacles, motor-driven appliances, or
transformer-supplied appliances.
!
CAUTION: Risk of Fire, Explosion, Leakage, and Burns.
Do Not Recharge, Disassemble, Heat Above 212 °F (100 °C)
or Incinerate. This product contains a lithium button/coin cell
battery. Keep batteries away from children. If a new or used
lithium button/coin cell battery is swallowed or enters the
body, it can cause severe internal burns and can lead to death
in as little as 2 hours. Always completely secure the battery
compartment. If the battery compartment does not close
securely, stop using the product, remove the batteries, and
keep the batteries away from children. If you think batteries
might have been swallowed or placed inside any part of the
body, seek immediate medical attention. The battery in this
device contains Perchlorate Material — special handling may
apply. For more information, visit
www.dtsc.ca.gov/hazardouswaste/perchlorate
Codes
Install in accordance with all national and local electrical
codes.
Grounding
When no “grounding means” exist in wallbox, the National
Electrical Code (NEC®) allows a control to be installed as a
replacement if 1) a nonmetallic, noncombustible faceplate is
used with nonmetallic attachment screws or 2) the circuit is
protected by a ground fault circuit interrupter (GFCI). When
installing a control according to these methods, cap or
remove green wire before screwing control into wallbox.
FCC / IC Information
This device complies with part 15 of the FCC Rules and
Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) This device
may not cause interference, and (2) this device must accept
any interference, including interference that may cause
undesired operation. Modifications not expressly approved
by Lutron Electronics Co., Inc. could void the user’s authority
to operate this equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician
for help.
x3
Hold for 6 seconds until light
bar starts blinking
Note: This setup MUST be completed if you are not using a smart hub. The Diva smart dimmer and Pico paddle
remote are not paired from the factory.
To Use your Caséta by Lutron System
1
Press and hold “off” button on dimmer
2
Press and hold “off” button on the Pico paddle remote
Pairing the dimmer and Pico paddle remote
For advanced features, tips for using Caséta dimmers with LEDs and CFLs, the complete Caséta product line,
and more, please visit www.casetawireless.com/features
Hold for 6 seconds until
lights flash 3 times
Option 1: With a smartphone or tablet (smart hub required, sold separately)
3
Use the Lutron app to complete ALL remaining steps
The Diva smart dimmer can be controlled from a smartphone when used with the
Lutron smart hub (formerly smart bridge) and the Lutron app.
If you are using the dimmer and remote control with the Lutron smart hub follow
the instructions below.
Lutron Smart Hub
Lutron app
Option 2: Without a smartphone or tablet (smart hub not required)
Control
three ways
Add devices
• Pico remotes
• Dimmers
• Shades
Schedule
your lights
Connect
while away
1
Download the Lutron app
2
Press and hold “off” button on remote
The Lutron app will walk you through
setting up your devices.
Launch the Lutron app
Search for “Lutron Caséta”
Repeat steps to pair other Pico paddle remotes
Adjusting low-end trim
When paired with Diva smart dimmer:
If off, lights to preset
If on, lights to full