Information Sheet

Customer Assistance:
1.844.LUTRON1 (U.S.A./Canada)
+44.(0)20.7680.4481 (Europe)
2www.lutron.com/support
product specifications
05.07.19
369221i
Specifications
Model Numbers Keypads: RRD-W1RLD-XX, RRD-W2RLD-XX, RRD-W3BD-XX,
RRD-W3BRL-XX, RRD-W3BSRL-XX, RRD-W3S-XX, RRD-W4S-XX,
RRD-W5BRL-XX, RRD-W5BRLIR-XX, RRD-W6BRL-XX, RRD-W7B-XX
Replacement Kits: RKD-W1RLD-XX-E, RKD-W2RLD-XX-E,
RKD-W3BD-XX-E, RKD-W3BRL-XX-E, RKD-W3BSRL-XX-E,
RKD-W4S-XX-E, RKD-W3S-XX-E, RKD-W5BRL-XX-E,
RKD-W5BRLIR-XX-E, RKD-W6BRL-XX-E, RKD-W7B-XX-E
Power 120 V
~ 50 / 60 Hz 0.5 A
Typical Power
Consumption
0.6 W
Test conditions: all backlights on medium intensity, two LEDs on (two
presets active), keypad powered at 120 V
~
Regulatory Approvals UL, CSA, NOM, FCC, IC, COFETEL, ANATEL
Environment Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C),
0% to 90% humidity, non-condensing. Indoor use only.
Communications Wall-mount designer keypads communicate with the system through
Radio Frequency (RF) and must be located within 30 ft (9 m) of a
repeater. System devices operate on frequencies between 431.0 MHz
and 437.0 MHz.
ESD Protection Tested to withstand electrostatic discharge without damage or memory
loss, in accordance with IEC 61000-4-2.
Surge Protection Tested to withstand surge voltages without damage or loss of operation,
in accordance with IEEE C62.41-1991 Recommended Practice on
Surge Voltages in Low-Voltage AC Power Circuits.
Power Failure Power failure memory: should power be interrupted, the keypad will
return to its previous state when power is restored.
Mounting Requires a U.S. wallbox. 3 ½ in (89 mm) deep recommended,
2 ¼ in (57 mm) deep minimum.
Wiring Wall-mount designer keypads require a neutral wire connection.
Warranty www.lutron.com/TechnicalDocumentLibrary/warranty.pdf
RadioRA 2 Wall-mount Designer Keypads
•
At the press of a single button, lights fade ON
or OFF to desired levels and shades/draperies
open or close to desired positions.
•
Light levels and shade/drapery positions can
be fine-tuned by pressing and holding the
raise / lower buttons.
•
Programmable to select scene or room preset
levels or positions.
•
Adjustable backlight intensity.
•
-W5BRLIR only: IR receivers at the front and
back of the keypad allow for the use of an IR
remote for line-of-sight operation (front) or IR
repeater kit integration (back).
Design Features
•
Use an IR remote to select the same
programmed rooms, scenes, and raise / lower
buttons as the keypad (-W5BRLIR only).
•
Configurable Raise/Lower selection using
programming software.
– Last button pressed (default) -
devices controlled by the last button
pressed will raise / lower.
– Double-tap - devices controlled by a
double-tapped button will raise /lower.
– Programmed devices - only the devices
programmed to the button will raise/lower.
•
Prepaid engraving included. Redeemable for
one engraved Replacement Kit.