Installation Manual
Table Of Contents
- Table of Contents
- About Integration
- Stanza
- QS Standalone
- RadioRA 2
- Quantum
- HomeWorks QS
- Devices
- Stanza Keypads
- Tabletop Stanza Keypads
- Stanza Dimmers
- Stanza Switch
- Stanza Lamp Module
- Stanza Input/Output Interface
- GRAFIK Eye QS
- Energi Savr Node QS/DALI
- Energi Savr Node QS/Int'l 0-10V
- Energi Savr Node QS/EcoSystem
- Energi Savr Node QS/0-10V
- seeTouch QS Keypads
- seeTouch QS Int'l Keypads
- Sivoia QS Shades
- Sivoia QS Venetian Blinds
- Maestro Dimmers
- Hybrid Keypad
- Tabletop seeTouch Keypads
- Pico Wireless Controls
- Visor Control Receiver
- Radio Powr Savr
- HVAC Controller
- Wireless Temperature Sensor
- Dynamic Keypad
- Programmers Appendix
- Contact Information
21
Lutron® integration protocol
Example PROGRAMMING Commands
For a system of one shade (Integration ID “living room sheer”), one Venetian blind (“kitchen venetian”), and
one QSE-CI-NWK (Integration ID “1”), the following examples show how programming can be done.
Operation Command String
Add shade at 100% to phantom button 1 #PROGRAMMING,1,1,1,living room sheer,0,100<CR><LF>
Response Received ~PROGRAMMING,1,1,1,living room sheer,0,100<CR><LF>
Add Venetian blind at 0% lift and 50% tilt
to phantom button 2
#PROGRAMMING,1,2,5,kitchen venetian,0,0,50<CR><LF>
Response Received ~PROGRAMMING,1,2,5,kitchen venetian,0,0,50<CR><LF>
Add Venetian blind at 75% tilt to phantom
button 3
#PROGRAMMING,1,3,6,kitchen venetian,0,75<CR><LF>
Response Received ~PROGRAMMING,1,3,6,kitchen venetian,0,75<CR><LF>
Add Venetian blind at 15% lift to phantom
button 4
#PROGRAMMING,1,4,7,kitchen venetian,0,15<CR><LF>
Response Received ~PROGRAMMING,1,4,7,kitchen venetian,0,15<CR><LF>
Add shade at 50% to phantom button 2 #PROGRAMMING,1,2,1,dining room blackout,0,50<CR><LF>
Response Received ~PROGRAMMING,1,2,1,dining room blackout,0,50<CR><LF>
Turn ON Stop-If-Moving for phantom
button 5
#PROGRAMMING,1,5,4,1<CR><LF>
Response Received ~PROGRAMMING,1,5,4,1<CR><LF>
Clear programming from all the phantom
buttons
#PROGRAMMING,1,0,3<CR><LF>
Response Received Repeat command to clear all phantom button programming
Repeat command to clear all phantom
button programming
#PROGRAMMING,1,0,3<CR><LF>
Response Received ~PROGRAMMING,1,0,3<CR><LF>
Clear programming from phantom button
6
#PROGRAMMING,1,6,3<CR><LF>
Response Received ~PROGRAMMING,1,6,3<CR><LF>
PROGRAMMING Command Formats
Integration ID or Serial # of
the QSE-CI-NWK being used
See table
below
Operation
Phantom Button #
(can be 1-100)
Command
#PROGRAMMING, 1, Button#, Action#, Parameters
QSE-CI-NWK-E: PROGRAMMING Commands
Con/Act
FD/Col
DATA RX
DATA TX
RS232 RX
RS232 TX
LNK/ACT
PWR
1 2 3 4
1 2 3 4 5 6 7 8
QSE-CI-NWK-E
24 V 100 mA
800.523.9466
1.610.282.3800
www.lutron.com/qs
QS Link
QS Standalone System Commands (continued)