Owners manual

ManualsBrandsLuverne ManualsAutomotive240923 6 in. Oval Tubular Steps Fits 09-14 F-150

Page 1 of 3

PARTS LIST:

Qty

Description

Qty

Description

Driver/Left Side Bar

8mm Deep Clip Nuts

Passenger/Right Side Bar

8-1.25mm x 30mm Hex Bolts

Driver/Left Front-Passenger/Right Rear

Mounting Brackets

22 8-1.25mm x 25mm Hex Bolts

Passenger/Right Front-Driver/Left Rear

Mounting Brackets

10 8mm x 28mm OD x 3mm Large Flat Washers

Driver/Left Center Mounting Bracket

8mm x 24mm OD x 2mm STD Flat Washers

Passenger/Right Center Mounting Bracket

8mm Lock Washers

8mm Hex Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting on the driver side of the vehicle, locate the (2) holes in the bottom of the body panel, (pinch

weld). Next locate the rectangular opening and (2) small holes in the inner body panel directly above

the holes in the pinch weld, (Figure 1). NOTE: The holes in the inner panel may be covered with

sealing tape or insulation.

3. Slide (1) 8mm Clip Nut into the rectangular opening with the nut towards the inside. Line up the

threaded nut on the clip with the round hole, (Figure 1). Repeat to install 2nd 8mm Clip Nut in

remaining hole location.

4. Partially attach the driver side Mounting Bracket to the (2) Clip Nuts with the included (2) 8mm x 30mm

Hex Bolts, (2) 8mm Lock Washers and (2) 8mm x 28mm Large Flat Washers, (Figure 2). Depending

on model and year, the brake cable may be run on the inside or outside of the Bracket. Do not tighten

hardware at this time. NOTE: The cradle on the front Bracket should face to the rear.

5. Align the bottom holes in the front Bracket with the (2) holes in the pinch weld. Bolt the Bracket to the

pinch weld using the included (2) 8mm x 25mm Hex Bolts, (4) 8mm STD Flat Washers, (2) 8mm Lock

Washers and (2) 8mm Hex Nuts, (Figure 2). NOTE: Insert the bolts up from the bottom of the pinch

weld and through the Bracket.

Driver/Left Rear

Mounting Bracket

Driver/Left Center

Mounting Bracket

Driver/Left Front

Mounting Bracket

Passenger/Right Rear

Mounting Bracket

Passenger/Right Center

Mounting Bracket

Passenger/Right Front

Mounting Bracket

Front

Driver/Left Sidebar

Passenger/Right Sidebar

INSTALLATION INSTRUCTIONS

PART#: 240923

6” OVAL BENT SIDE BAR

FORD F150 SUPERCREW CAB 09-14

Summary of content (3 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PART#: 240923 6” OVAL BENT SIDE BAR FORD F150 SUPERCREW CAB 09-14 PARTS LIST: Qty 1 1 2 2 1 1 Description Driver/Left Side Bar Passenger/Right Side Bar Driver/Left Front-Passenger/Right Rear Mounting Brackets Passenger/Right Front-Driver/Left Rear Mounting Brackets Driver/Left Center Mounting Bracket Passenger/Right Center Mounting Bracket Qty 10 10 Description 8mm Deep Clip Nuts 8-1.25mm x 30mm Hex Bolts 22 8-1.
PAGE 2
6" BENT END SIDEBARS 09-14 FORD F-150 CREW CAB 6. Next, move toward the center of the vehicle. Select the driver side center Mounting Bracket. Locate the (2) holes in the pinch weld similar to the front location, (Figure 3). Insert (1) 8mm Clip Nut into the rectangular opening and up to the single small round hole in the body panel. Secure the Bracket to the Clip Nut with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm x 28mm Large Flat Washer, (Figure 4).
PAGE 3
6" BENT END SIDEBARS 09-14 FORD F-150 CREW CAB Driver Side Installation Pictured 8mm x 30mm Hex Bolts 8mm Lock Washers 8mm x 28mm Large Flat Washers 8mm x 25mm Hex Bolt (2) 8mm STD Flat Washers 8mm Lock Washer 8mm Hex Nut Front (Fig 4) Driver/left center Bracket installed 8mm x 30mm Hex Bolts 8mm Lock Washers 8mm x 28mm Large Flat Washers Rear Rear (Fig 5) Driver side-rear Mounting Bracket location 8mm x 25mm Hex Bolt (2) 8mm STD Flat Washers 8mm Lock Washer 8mm Hex Nut Fig 6 (2) 8mm x 25mm Hex Bolts