Owners manual

INSTALLATION INSTRUCTIONS AND PARTS LIST

MODEL 415078, 415088, GRIP STEPS (BOARDS ONLY)

UNIVERSAL APPLICATIONS

1. Read instructions completely and check to make sure that all required parts (listed on the service

parts list) are on hand before starting the installation

2. Follow the instructions included with the specific bracket package that you are using to mount

the brackets to your vehicle.

3. Step assembly:

3.1 Before attaching the grip steps to the brackets, slide the appropriate number of support braces

(item #2) into the channel of the step (item #1).

3.2 Slide the end cap (item #3) over the front and rear of each step. Using the supplied #8 x 1/2”

self drilling tek screw (item #8), screw the end cap to the bottom of the step.

4. Attaching the step to the mounting bracket:

4.1 Set the step on the mounting brackets, and slide each support brace over the top of each

mounting bracket. Attach the flat spacer plate (item #4) to the bottom of the step, between the

support brace, and the top of the mounting bracket.

4.2 Using the supplied 5/16-18 x 1” carriage bolt, washer, and flange nuts, (item #5, 6, 7), attach

the step assembly, flat spacer plate and mounting bracket. (NOTE: Some of the flange nuts

are supplied in the specific bracket package, not the step package.)

4.3 Set the step plate in the correct position and tighten all fasteners.

Torque all 5/16” fasteners to 19 LB FT.

SERVICE PARTS LIST

ITEM PART NO. QTY DESCRIPTION

1 551384 2 EXTRUSION-AL,77.62, GRIP STEP,BLK,415078

1 551385 2 EXTRUSION-AL,87.75,GRIP STEP,BLK,415088

2 551296 8 SUPPORT BRACE, UPPER, GALV

3 551394 4 CAP-END,GRIP STEP, BLACK, PLASTIC

4 551298 8 SPACER PLATE, LOWER, BLACK

5 108683 16 BOLT-CRG,5/16-18 X 1.0”, SST

6 101369 16 WASHER-FLAT,5/16,SST

7 102680 16 NUT-SERR FLG,HX,SST,WX,5/16-18

8 107958 8 SCR-TEK #8-18 X 1/2”,SST,BLK

REV B 03DEC10

REV A 10JUL09

551267 SHEET 1 OF 2 20AUG08

PAGE 1
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 415078, 415088, GRIP STEPS (BOARDS ONLY) UNIVERSAL APPLICATIONS 1. Read instructions completely and check to make sure that all required parts (listed on the service parts list) are on hand before starting the installation. 2. Follow the instructions included with the specific bracket package that you are using to mount the brackets to your vehicle. 3. Step assembly: 3.
PAGE 2
PAGE 3
INSTALLATION INSTRUCTIONS AND PARTS LIST APPLICATION: MODEL 401743 GRIP-STEP/REGAL 7 BRACKETS ON: 2015+ GM 2500/3500HD DOUBLE & CREW CAB PICKUPS, GAS/DIESEL BODY MOUNT APPLICATION NO DRILL APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION. 2. ON THE LEFT SIDE OF THE VEHICLE PREASSEMBLE THE FRONT BRACKET (ITEMS #1, 3, 14) AS SHOWN IN FIG. 1 USING THREE 3/8”-16 X 1.
PAGE 4
6. INSTALL THE STEP BOARDS AS DESCRIBED BY THE INSTRUCTIONS INCLUDED WITH YOUR STEP BOARDS. (NOTE: INSURE THAT THE MOUNTING BRACKETS DO NOT TOUCH THE INSIDE WALL OF THE BODY MOUNT HOUSING AND TORQUE THE BODY MOUNT FASTENERS TO MANUFACTURES SPECS). 7. POSITION THE LOAD REACTION BOLT ASSEMBLY SO THAT THE RUBBER CUSHION IS SNUG UP AGAINST THE SIDE OF THE FRAME. TIGHTEN THE 3/8” FLANGE NUTS ON EITHER SIDE OF THE BRKT TO 19LB. FT. 8. REPEAT STEPS 1-8 FOR THE RIGHT SIDE OF THE VEHICLE.
PAGE 5
PAGE 6