Owners manual

ManualsBrandsLuverne ManualsAutomotive584098-570929 O-Mega II 6 in. Wheel To Wheel Oval Steps Fits 09-14 F-150

INSTALLATION INSTRUCTIONS AND PARTS LIST

MODEL: 583098, 583102, 583108, 583114, 583125, 584098, 584102, 584114, 584125 O-MEGA II 6” OVAL

STEPS

UNIVERSAL APPLICATION

1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS

(LISTED ON TH

E SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION.

2. FOLLOW THE INSTRUCTIONS INCLUDED WITH THE SPECIFIC BRACKET PACKAGE THAT YOU

ARE USING, TO MOUNT THE BRACKETS TO YOUR VEHICLE.

3. BEFORE ATTACHING THE O-MEGA STEPS TO THE BRACKETS, PLACE THE STEP PADS (ITEM #2)

ON TOP OF THE STEP PLATES. USE THE TABLE ON SHEET #2, AS A GUIDE TO POSITION THE

STEP PAD FOR YOUR PARTICULAR VEHICLE. WHEN INSTALLING THE PADS ON THE STEPS,

DRILL (5) 1/8'” HOLE USING THE STEP PAD AS A GUIDE. ATTACH WITH (5) 8-18X1/2'” TEK

SCREWS (ITEM #6) PROVIDED. REPEAT FOR ALL STEP PADS. (NOTE: DUE TO THE SHORTNESS

OF SOME BOXES, MOUNT THE BOX STEP PAD FIRST, APPROXIMATELY ½” FROM THE END

CAP AND THEN MOUNT THE MIDDLE STEP PAD ACCORDINGLY.)

4. INSTALL THE REQUIRED NUMBER OF SQUARE HEAD BOLTS INTO THE DESIGNATED SLOTS IN

THE BOTTOM OF THE STEP PLATES.

5. INSTALL THE END CAPS (ITEM #3) AS SHOWN IN fig. 1, TIGHTENING THE NUTS TO 5 LB FT.

6. POSITION THE O-MEGA STEP ON THE MOUNTING BRACKETS SO THAT THE SQUARE HEAD

SCREWS (ITEM #4) ARE LOCATED IN THE SLOTS OF THE MOUNTING BRACKETS AND THE STEP

IS CENTERED, FRONT TO REAR, ON THE VEHICLE. INSTALL 5/16” SERRATED FLANGE NUTS

(ITEM #5) ON THE SQUARE HEAD SCREWS (ITEM #4) AND TIGHTEN TO 19 LB FT.

SERVICE PARTS LIST

553118 SHEET 1 OF 2 05OCT16

ITEM PART NO. QTY

DESCRIPTION

1 553074 2 EXTRUSION-AL,95.0,OMEGA STP,SILVEER

1 553075 2 EXTRUSION-AL,99.0,OMEGA STP,SILVER

1 553076 2 EXTRUSION-AL,105.0,OMEGA STP,SILVER

1 553077 2 EXTRUSION-AL,111.0,OMEGA STP,SILVER

1 553078 2 EXTRUSION-AL,122.0,OMEGA STP,SILVER

1 553062 2 EXTRUSION-AL,95.0,OMEGA STP,BLACK

1 553063 2 EXTRUSION-AL,99.0,OMEGA STP,BLACK

1 553065 2 EXTRUSION-AL,111.0,OMEGA STP,BLACK

1 553066 2 EXTRUSION-AL,122.0,OMEGA STP,BLACK

2 107957 6 ALUM,STP-PAD,BLK,OMEGA-STEP

3 107956 4 CAP-END,PLSTC,2.95 X 6.70

4 106880 28 SCREW-SQ HD,5/16-18 X 1,MAGNIGUARD

5 102680 28 NUT-SERR FLG,HX,SST,WX,5/16-18

6 107958 30 SCREW-PPH,TEK,#8-18 X 1/2",SST,BZP

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL: 583098, 583102, 583108, 583114, 583125, 584098, 584102, 584114, 584125 O-MEGA II 6” OVAL STEPS UNIVERSAL APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON THE SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION. 2. FOLLOW THE INSTRUCTIONS INCLUDED WITH THE SPECIFIC BRACKET PACKAGE THAT YOU ARE USING, TO MOUNT THE BRACKETS TO YOUR VEHICLE. 3.
PAGE 2
STEP PAD LOCATION GUIDE VEHICLE MODEL SILVERADO/SIERRA DOUBLE CAB SILVERADO/SIERRA EXTENDED CAB SILVERADO/SIERRA CREW CAB CHEVROLET EXPRESS VAN & GMC SAVANA VAN RAM QUAD CAB RAM CREW CAB RAM MEGA CAB FORD F150 SUPER CAB FORD F150 SUPER CREW CAB FORD F150 SUPER CREW CAB FORD SUPER DUTY SUPER CAB FORD SUPER DUTY CREW CAB FORD PAD A 14-3/4 14-3/4 14-3/4 7-1/2 10-1/2 10-1/2 10-1/2 18-1/4 18-1/4 18-1/4 6-7/8 6-7/8 7-1/2 PAD B 46-3/4 41-3/4 54-1/4 N/A 46 48 52-1/16 46-1/4 56-1/2 56-1/2 39-1/16 52-7/8 N/A NOTE
PAGE 3
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 570929 W2W MEGA STEP BRACKETS: 2009 AND NEWER FORD F-150 REGULAR CAB PICKUPS 2009 AND NEWER FORD F-150 SUPER CAB PICKUPS 2009 AND NEWER FORD F-150 SUPERCREW PICKUPS 1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION. 2. EXISTING MOUNTING HOLE PATTERNS ARE LOCATED ON THE PINCH WELD AND INTERIOR WALL OF THE ROCKER PANEL.
PAGE 4
6. ATTACH THE STEP (ITEM #1) TO THE MOUNTING BRACKETS. 6.1. INSERT FOUR (4) 5/16” SQUARE HEAD SCREWS (ITEM #3) IN THE CENTER SLOT ON THE UNDER SIDE OF THE STEP. 6.2. POSITION THE STEP ON THE FRONT THREE MOUNTING BRACKETS SO THAT THE SQUARE HEAD SCREWS ARE LOCATED IN THE SLOTS OF THE MOUNTING BRACKETS AND THE STEP IS CENTERED, FRONT TO REAR, ON THE CAB. 6.3. LOCATE THE STEP, IN AND OUT, AS DESIRED AND INSTALL 5/16” SERRATED FLANGE NUTS (ITEM #4) ON THE SQUARE HEAD SCREWS.
PAGE 5