Owners manual

INSTALLATION INSTRUCTIONS AND PARTS LIST
MODEL 570929 W2W MEGA STEP BRACKETS:
2009 AND NEWER FORD F-150 REGULAR CAB PICKUPS
2009 AND NEWER FORD F-150 SUPER CAB PICKUPS
2009 AND NEWER FORD F-150 SUPERCREW PICKUPS
1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS
(LISTED ON SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION.
2. EXISTING MOUNTING HOLE PATTERNS ARE LOCATED ON THE PINCH WELD AND INTERIOR
WALL OF THE ROCKER PANEL. THESE MOUNTING HOLE PATTERNS WILL BE USED TO MOUNT
THE CAB BRACKETS FOR THIS INSTALLATION PER THE FOLLOWING INSTRUCTIONS.
2.1. INSTALL 5/16” MULTI THREAD U-NUTS (ITEM #5) IN THE TOP REAR HOLES OF THE FRONT
AND CENTER PATTERNS AND IN THE TOP FRONT HOLE OF THE REAR PATTERN AS SHOWN.
INSTALL THESE U-NUTS SO THAT THE THREADS ARE TO THE INSIDE OF THE ROCKER
PANEL. (THIS IS DONE BY INSERTING THE THREADED HALF OF THE U-NUT THRU THE
LARGE ACCESS HOLES AND SLIDING THE U-NUT TOWARDS THE ROUND HOLE UNTIL IT
SEATS IN THE ROUND HOLE).
3. ATTACH THE FRONT AND REAR MOUNTING BRACKETS (ITEM #2) TO THE VEHICLE.
3.1. POSITION THE BRACKETS ON THE VEHICLE SO THAT THE TOP HOLE LINES UP WITH THE
MULTI THREAD U-NUT AND THE HOLE IN THE OFFSET LINES UP WITH THE HOLE IN THE
PINCH WELD. ATTACH THE TOP OF THE BRACKET WITH A 5/16” X 1.00” ZINC PLATED HEX
HEAD CAP SCREW (ITEM #6) AND 5/16” ZINC PLATED FLAT WASHER (ITEM #7).ATTACH THE
BOTTOM OF THE BRACKET TO THE PINCH WELD WITH A 5/16” X 1.00” BLACK PLATED HEX
HEAD CAP SCREW (ITEM #8) 5/16” BLACK PLATED FLAT WASHER (ITEM# 9) AND 5/16”
SERRATED FLANGE NUT (ITEM # 4). LEVEL THE BRACKETS AND TIGHTEN THE FASTENERS
TO 19 LB FT.
3.2. FOR REG CABS & SUPER CABS THE CENTER BRACKET CAN BE INSTALLED THE SAME WAY
AS IN STEP 3.1 FOR SUPER CREW PROCEED TO STEP 4.
SUPER CREW ONLY
4. ATTACH THE MIDDLE MOUNTING BRACKET (ITEM #2) TO THE VEHICLE
4.1 ATTACH ANGLE BRACKET (ITEM #10)TO MOUNTING BRACKET (ITEM #2) WITH A 5/16” X
1.00” ZINC PLATED HEX HEAD CAP SCREW (ITEM #6)AND A 5/16” SERRATED FLANGE NUT
(ITEM #4)TOGETHER WITH THE ANGLE TOWARDS THE MULTI THREAD U-NUT IN THE HOLE
THAT IS OFFSET FROM THE PINCH WELD HOLE . REPEAT STEP 3.1 USING ANGLE BRKT.
5. ATTACH INBOARD BRACKET AND OUTBOARD BRACKET (ITEMS #11&12)USING 5/16” X 1.00”
BLACK ZINC PLATED HEX HEAD CAP SCREW (ITEM# 8) AND (4) 5/16” BLACK ZINC PLATED FLAT
WASHERS (ITEM# 9) AND SERRATED FLANG NUT BLACK ZINC (ITEM# 14). FINGER TIGHT ONLY
UNTIL BOARD IS POSITIONED.
5.1 REMOVE FACTORY NUT FROM SHACKLE MOUNT. PLACE BRACKET OVER STUD AND
REPLACE FACTORY NUT.FINGER TIGHTEN ONLY
551709 SHEET 1 10JUN08