Specification

ManualsBrandsLUXIER ManualsBathContemporary 8 in. Widespread 2-Handle Bathroom Faucet with Pop-Up Drain in Matte Black

WSP11 Rev. B 03/2021Luxier USA

Widespread Two Handles Lavatory Faucet

WSP11-TB (Brushed Nickel)

WSP11-TC (Chrome)

WSP11-TG (Brushed Gold)

WSP11-TM (Matte Black)

WSP11-TO (Oil Rubbed Bronze)

Features:

- Three Hole Installation

- Drip Free 1/4 Turn Ceramic Cartridge

- Maximum ow rate 1.2 gpm at 60 psi

- Complies with:

ADA

NSF 61-9

ANSI / ASME A112.18.1

IAPMO / UPC / cUPC

CA AB-1953

CEC

Max. Deck Thickness 1.5”

* Drawing not to scale. All Measurements are approximate*

1.375” Hole Size

Approx. 22” long hose with 3/8” compression ttings

8.03”

5.08”

4.92”

Recommend 10” - 12” spread

1.97”

3.15”

1.89”

Summary of content (4 pages)

PAGE 1
Widespread Two Handles Lavatory Faucet WSP11-TB (Brushed Nickel) WSP11-TC (Chrome) WSP11-TG (Brushed Gold) WSP11-TM (Matte Black) WSP11-TO (Oil Rubbed Bronze) Features: - Three Hole Installation Drip Free 1/4 Turn Ceramic Cartridge Maximum flow rate 1.2 gpm at 60 psi Complies with: ADA NSF 61-9 ANSI / ASME A112.18.1 IAPMO / UPC / cUPC CA AB-1953 CEC 4.92” Recommend 10” - 12” spread 8.03” 5.08” 3.15” 1.97” 1.89” Max. Deck Thickness 1.5” 1.375” Hole Size Approx.
PAGE 2
Thank you for purchasing Luxier products. Please read the information below and keep this installation guide for future reference. If you require assistance, please contact our customer service department at 1-877-711-8828, Monday - Friday 9AM - 5PM Pacific Time or by email at support@luxierusa.com. Limited Lifetime Warranty (For USA Only) The manufacturer warrants this product to be leak and drip free during daily normal household use for as long as it is owned by the original purchaser of this product.
PAGE 3
Parts Diagram 13 01 21 14 15 16 02 03 17 04 18 05 19 06 07 08 09 20 10 11 12 You may also need the following tools 1. Safety Glasses 2. Teflon (PTFE) Tape 3. Plumber’s Putty and Caulking 4. 1 3/8” Basin Wrench 01. Handle 02. Hex Screw 03. Cap 04. Bonnet 05. Cartridge 06. O-Ring 07. Plastic Base 08. O-Ring 09. Valve Body 10. Locking Nut 11. Inlet Water Hose 12. Outlet Water Hose 13. Spout 14. Mounting Rod 15. C Shaped Washer 16. C Shaped Metal Washer 17. Locking Nut 18. Spout Inlet Hose 19.
PAGE 4
Installation A B COLD C HOT A. Shut off water supply at the valves. Remove old faucet and clean the mounting surface for installation of new faucet. B. Place spout through the center mounting hole on the surface. Secure spout with C shaped washer, C shaped metal washer and locking nut. E D C. Insert the Tee connector to the center spout inlet hose until it clicks in place. Make sure the hose is fully inserted. There will be an audible click when the connector is connected properly.