AM/FM STEREO RECEIVER model R1500 OPERATION MANUAL
You are about to begin a new high f idelity experience. The LUXMAN R-1500 Receiver is unique in the annals of high fidelity equipment. Though built with extremely sophisticated engineering, its concept is quite simple: to produce a receiver with performance comparable to that available in the f inest separate tuners, preamplif iers and amplif iers. After extensive research,the R-1500 was designed without compromise to provide high output. low distortion and an exceptionally wide range of available power.
stereo this beacon lights up automatically to indicate stereo recept¡on. On the contrally if reception changes from stereo to mono, the beacon does not light. In case rnono reproducÌion of stereo signal is desired, set the mode selector switch (9) to mono position. 7 MICROPHONE LEVEL CONTROL (PULL ON MIC. LEVEL} The input level of the microphone jack(8 ) is controlled by this knob Normally this switch should be left pressed in. Pull the knob outwards and the crrcuit is put into operation.
fuse. When the fuse is blown, replace ir, ascertaining the cause of failure and rendering appropriate remedy. Replacement can be easily done by hand turning the cap to the direction of arrow mark Be sure that the mains cord is disconlrected from the mains power supply 3A(E-TYPE) por Spea ln case normal reception is possible with the built-in kers". 30. AM FERRITE CORE ANTENNA (BUILT.
INSTALLATION with the R-1500. For FlV, a folded dipole, available from your dealer, is generally adequale. This section will tell you While the R-1 500 Receiver has been designed for maximum ease of installation and operation, we strongly suggest you read this section through before proceeding to connect and operate the unit. Because the B-1500 incorporates manV how to connect them. technical and operating refinements, it may be a bit different from equÌpment you have used in the past.
speakers are out of phase. Should thìs occur, turn off the receiver and carefully reverse the connections at either one of the speaker TURNTABLES/TAPE R ECORDERS.DECKS AUTOMATIC AND MANUAL TURNTABLES The R 1500 has 2 provisions for connection of two turntables. Check the cartridge manual or your dealer, if in doubt about the proper input for the particular cartr¡dge in your turntable.
PLAYBACK FROM RECORD DISC ICONNECTIONS Generally a record player consists of a turntable ensuring constant rotation of the record disc a pick-up (cartridge) whose stylus (needle) traces the sound groove of the disc converting the physical signal of the record sound into the electric signal, and the arm which holds this cartridge. The player has 2 cords with pin plug at its end for both right and left channels. Connect the pin connectors to the input terminals of this receiver IPHONO-1(37) or PHONO-2(37)].
original sound and newly recorded one. Remember that for reproductiorr of other programme sources than tape this switch as well as the Tape fVonitor Switch(11) must be set at the centre "sourcel' position. lf there are 2 |ape-recorders reprinIing of tape is feasible also by other method; Corrrrect the tape-recorder of betler recording performance to the Recording Output Terlrritrals and otlrer one to the AUX terminals exclusively for play back setting the Input Selector Switch to the relevatrt pos r tr on.
been carefully preset, and the overall response curve maintains complete linearity from 50Hz to above 10KHz, unlike the curvature in response normally associated with ordinary tone controls Specif ically, when the control is turned to the first "up-tilt" position it w¡ll decrease bass and increase treble by 15dB at 'l 00Hz and l0KHz respectively, while selection to the second "up-tilt" posìtion will result in a 3dB cut and boost at these same frequencies.
SPECIFICATIONS I ¡ AUDIO SECTION GIRCUIT: RMS POWER: T.H.D.: FREOUENCY RESPONSE: POWER BANDWIDTH: INPUT SENSITIVITY: Fully complementary direct coupled D.C. output amp utilis¡ng dual rail power supply 75/7swatts (8ohms, both channels driven at rated dist., 20Hz-20KHz) ( o.osg¿ (8ohms, 20Hz-20KHz at any power level below rated output) 1SHz - 35KHz (*1dB) SHz - 75KHz (:3dBl SHz - 40KHz (0.1%, -3dBl PHONO 1, PHONO 2 2.7mV 1,2 (at 7swatts, 8ohmsl TAPE MONITOR 1,2 (at 75Watts, Sohms) MlC.
¡ä J! r h tUX CORPORATION, JAPAN HEAD OFFICE & FACTOFY 1]831 NAGAHASHI. NISHINABI.