Flat Panel Series Mobile Stand Instructions TYPE1 Stationary Mount Base Model TYPE3 Stationary Mount + Shelf + Camera Mount 09/23/13 TYPE2 Stationary Mount + Shelf TYPE4 Rotating Mount + Shelf
Table of Contents Table of Contents and Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Assembly and Installation Adjust upper and lower poles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attaching to the base assembly . . . . . . . . . . . . . .
Part List A1 x1 B2 x2 B2 x2 B1 x1 B1 x1 A2 x4 B3 x2 A3 x4 B5 x2* (B3 is preinstalled) A4 x1 B4 x4 TYPE1, TYPE2, TYPE3 *1 is pre-installed C5 x4 C4 x4 C3 x4 C2 x2 C1 x1 C3 x2 D x2 R3 x1 only: TYPE2, TYPE3, TYPE4 S2 x1 S1 x1 R1 x1 only: TYPE3 M8x25mm M6x25mm M5x25mm G x4 H x4 J x4 M8x20mm K x4 B5 x2 TYPE4 C1 x1 C2 x2 R2 x1 TYPE4 TYPE1, TYPE2, TYPE3 M5x10mm F x4 M6x10mm N x2 T x8 only: TYPE3 E x4 P x2 L x1 only: TYPE1, only: TYPE3 TYPE2, TYPE3 only: TYPE2, TYPE3, TYPE4
1 1 2 3 Adjust upper and lower poles Locate the spring plungers inside the bottom grommet hole of pole B1 (If your unit has B5 cross bar pre-installed remove prior). Starting with the right side pole B2, push the spring plunger down and pull B2 up slightly and twist it slightly so that the spring plunger remains offset. This will make adjusting the pole easier. (figure 1) Hold the poles B1 & B2 with your hands and use your left foot on the cross bridge of B1 for stability.
2 Attaching to the base assembly 1 Thread casters A2 and washer A3 into the bottom of base A1. Make sure all casters are locked to prevent movement during installation. 2 With allen wrench M attach lower poles B1 to base A1 with screw K. First through the bottom of base A1, then through the top of base A. 3 After screws K are firmly fastened, push down the screw cover A4 until it locks into place.
3 Install steel cross rods B5 B5 1 B5 B2 B5 Phillips screwdriver 3 Refasten rods B5 with screws. Remove the pre-installed screws on rod B5. Making sure the upper poles B2 are aligned, slide rods B5 into the top openings. 4 Height adjustment Assistance Required Cables Unplugged 461⁄2˝ - 621⁄2˝ H / 1050mm - 1500mm B4 B4 6 / 12 2 B4 B4 Slide the upper poles B2 up or down to the different spring plunger holes for your desired height. Install grommet covers B4 into the grommet holes.
5 Media shelf assembly (TYPE2, TYPE3, TYPE4) Before assembly make sure there is enough clearance for the flat panel display 1 Remove the pre-installed screws on bracket R2. Align bracket R2 to desired position and clamp R2 then retighten the long screws. L R2 2 1 B1 Phillips screwdriver 3 2 R1 1 R3 R3 R2 2 Phillips screwdriver Using the short screws fasten bracket R2 to support R3. With allen wrench L and the short allen screws fasten shelf R1 to support R3.
6a Assemble flat panel mount (TYPE4) VESA: 200x400 - 400x400mm 1 2 C1 1. C3 3. C4 C2 C2 2. C2 C1 4. C5 Phillips screwdriver Top of Display 3 For a selection of mounting positions refer to page 12 C2 C2 F E Display not included First unscrew and remove the vertical supports C2 from mount C1. Align the screw threads C3 to the desired vertical support position of C2. Screw support C2 into C1 and C3. Insert support stoppers C4 followed by caps C5.
Adjusting the mount (TYPE4) - After Step 7 Remove pre-installed screws Re-attach screws C1 C1 Phillips screwdriver Phillips screwdriver Swivel 90° 6b Assemble flat panel mount (TYPE1, TYPE2, TYPE3) VESA: 200x200mm F E E F Phillips screwdriver H, J M5x25mm (H) M6x25mm (J) H,J VESA: 200x200 - 600x400mm T T H,J E F Safety Precautions F E H, J 9 / 12
7 Install mount to frame 1 2 Lift up lock hook before installing mount C1 Make sure casters are locked prior to installation 3 4 Secure lock hook fully Heavy Lifting: Assistance Required Attach hooks on C1 onto cross rods B5 C1 10 / 12 B5 Lock not included
8 Install camera mount (TYPE3) S1 Adjustable height S2 P 9 N Phillips screwdriver Cable and wire Installation Please use care when inserting the wires and cables into the grommet to avoid damage For indoor use only. Avoid excessive wind, heat & humidity.
10 VESA mounting patterns 09/23/13 Slide vertical support rails to find the best assembly position for your display. D For 200x200mm VESA mounting position use brackets D.
