Electrical Operated Stand Up Desk Assembly Guide for 60˝ & 48˝ Wide Flat Top Desks
Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings & Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parts List & Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembly and Installation Assemble the right and left frame . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using the product. Every person who is responsible for this table at installation or employment of the table in daily use or in service and repair work should carefully read these instructions. Keep these instructions close to your sit/stand table. DANGER To reduce the risk of electric shock: Always unplug this furnishing from the electrical outlet before cleaning.
Adjusting Table Height: 1. 1. Make sure no objects will obstruct the table when adjusting table height. 2. 2. In order to run the table up/down, press the controller buttons with an arrows pointing up and down respectively. 3. Unplug the hand controller when 3. not in use to prevent unauthorized use. Safety Regulations: • When the table is run up/down, keep a safe distance to avoid the risk of being squeezed between the moving table top and fixed objects in the surrounding area.
Parts List A x1 B x1 J x2 K x2 C x2 E x1 G x1 D x1 F x1 H x1 R x4 L x4 N x1 P x1 Hardware (Actual Size) 1 x1 2 x1 3 x2 M5 M4 9 x1 6 x2 M6x36 4 x4 M6x48 5 x4 M6x73 8 x16 M8x15 5 / 16
1 Assemble the right and left frame Tighten casters fully with included wrench J K 9 J K R R R R B A Gather Parts: A, B, J, K, R, 9 6 / 16
2 Assemble the cross bars B A 4 C 4 C 4 2 4 C Make sure the indented center holes of the cross bars C are facing towards the casters Assistance Recommended Gather Parts: C, 2 & 4 x4 M6x48 7 / 16
3 Attach electric adjustment housing 1 D IMPORTANT: Do not tighten screws (8x16) fully until all are in place 2 8x4 8x4 8x4 D 8x4 1 Gather Parts: D, 1 8 / 16 & 8 x16 M8x15
4 Flip desk upright and install optional electric 1 Heavy Lifting: Assistance Required 2 Back Front IMPORTANT: Install the OPTIONAL electric (SOLD SEPARATELY) before attaching the desk top to the frame.
5 Install rotating cross bar 1 N E E 2 E N 3 Gather Parts: N, E 10 / 16 E
6 Mount power supply to unit 1 H G 2 Feed the cords through the cable management holes. Make sure to tuck any excess cables away from the motor to avoid tangles.
7 Plug in electrical cords to power supply 1 Attach the cable that is connected to the motor to the center plug. Make sure the pins line up correctly. 2 Attach the cable that is connected to the controller to the left plug. Make sure the pins line up correctly. G 5 12 / 16 To set up the system, hold the right button untill the unit is at its lowest position then wait for five (5) seconds. Also do this when a power outage occurs or if the unit has been unplugged.
8 Attach the desk surface F Front Back 5 5 5 5 2 Gather Parts: F & 5 x4 M6x73 13 / 16
9 Attach remaining bolts to the desk surface F 3 3 14 / 16 2 3 x2 M6x36
10 Mount electrical controller and cable clips L x4 Attach cable management clips to desired position MAKE SURE TO LEAVE PLENTY OF SLACK FOR CABLES TO MOVE FREELY DURING THE DESK ADJUSTMENT P G Phillips Screwdriver required for tightening screws 6 Gather Parts: P, G, L 6 6 & 6 x2 15 / 16
Revision Date: 09/09/2015 Questions or Feedback Call Us at: 800-323-4656