Installation Guide

www.allstarlighting.com
SAFETY INFORMATION PACKAGE CONTENTS
INSTALLATION GUIDE
LR23751, LR23756, LR23761
33 Randolph Ave. • Avenel NJ 07001 | 732-882-1500
1
3”, 4” & 6” CCT COLOR CHANGE ROUND MINI PANEL
1. TURN OFF THE MAIN POWER.
2. Use the template to mark the desired installation location and use a
drywall saw to cut the opening marked by the template.
3. To connect the wires open the junction box (A) cover and remove the knockout on the
side panel, insert the electrical supply cable through the knockout (1). Connect the green
ground wire from the junction box to the ground wire from the supply circuit, the black wire
from the junction box to the black wire from the supply circuit, and the white wire from the
junction box to the white wire from the supply circuit. Secure the wire in the knockout hole
using a cable clamp (not provided). Place all wiring and connections into the junction box
and close the cover. Plug the connector cable from the junction box (A) into the connector
cable from the light panel (C).
5. To installt the junction box and light panel, insert the junction box (A) through the
mounting hole. Push the spring-loaded panel base into the mounting hole. Release the
clips. The light panel (C) will be pulled flush to the ceiling. For airtight installations, install
the foam gasket (B) between the light panel (C) and the ceiling.
IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
Most electrical accidents are caused by carelessness or ignorance. Review these
basic electrical guidelines before you begin this installation.
– Use tools with insulated handles and ladders made of wood or fiberglass.
– Keep dry-chemical fire extinguishers in the kitchen, basement, and workshop.
– Never disable grounding devices. Ensure all appliances that require grounding
are properly grounded, and that the electrical system itself is properly grounded.
– Meet or exceed all electrical code requirements that cover the work you are doing.
– Always work with enought light to see what you are doing. It is easy to make a
mistake when you work in dim light.
– When in double about the safety of any electrical repair or test, call in a
professional.
– This fixture is IC rated for direct contact with insulation.
– †his fixture is intended for indoor use only.
– Do not modify this fixture. If any modifications are made, it may render the
product unsafe and void the warranty.
WARNING
Before touching any wire, use a voltage tester to ensure it is not live.
WARNING
When you check for voltage in a receptacle, check both outlets as each
may be controlled by a separate wiring circuit.
WARNING
Before working on a circuit, go to the main service panel and remove
the fuse or trip the breaker that controls that circuit. Tape a sign to the
panel warning others to leave the circuit alone while you work.
WARNING
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT
BRANCH CIRCUIT CONDUCTOR.
WARNING
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment. This device comlies with part 15 of the FCC
rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CARE AND CLEANING
To clean the fixture, first disconnect the power by turning off the
circuit breaker. Use a dry or slightly dampened, clean cloth to wipe off
the surface of the fixture, use clean water, never use a solvent. Allow
the fixture to dry completely before power is restored.
TOOLS REQUIRED: Ladder, Safety Goggles, Gloves, Drywall Saw, Wire Strippers, Pencil, Cable
Clamp, Connection Terminal
A B C D
1 Junction Box 1 Foam Gasket 1 Light Panel 1 Template
C
C
B
A
A
1
A
4. Use the CCT switch (1) on junction box to select color.
1
A
C