Simply Connected Quick Install Guide XAP-1040 Luxul High Performance Outdoor 802.11b/g/n Wireless Access Point Use the XAP-1040 to: Provide a High Performance Outdoor 802.
XAP-1040 Quick Install Guide Quick Install Guide Model Number: XAP-1040 High Performance Outdoor 802.11b/g/n Wireless Access Point FCC ID: W59XAP1040 IC: 8584A-XAP1040 © 2015 Luxul All rights reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design.
Simply Connected PACKAGE CONTENTS The following items should be included in the box: XAP-1040 Wireless Access Point Weather Resistant RJ45 Connector Gland POE Injector, Power Adapter, Noise Suppresser Dual Purpose Mounting Bracket for Wall or Pole Quick Install Guide NOTE: If any of the listed items are missing or damaged, please contact the reseller from whom you purchased for return/replacement.
XAP-1040 Quick Install Guide XAP-1040 Rear View Bottom View The bottom of the XAP-1040 provides one RJ-45 connection that is used to deliver both power and data to the access point. When installation is complete, a weather resistant RJ-45 connector gland will cover the RJ-45 connection. XAP-1040 Bottom View Inside View For maximum weather resistance, all System LEDs and the Reset button are located internally. Unless it becomes necessary to do so, opening the XAP-1040 is not suggested.
Simply Connected View of XAP-1040 Opened PREPARING FOR INSTALLATION System Requirements Devices Supporting 802.11b, 802.11g or 802.11n Web Browser (Microsoft IE 8.0 and up, Mozilla Firefox 10 and up, Safari 2.0 and up, Google Chrome 4.
XAP-1040 Quick Install Guide With the base lifted to the right, System LEDs and the Reset button can be seen as shown here: Reset Button Reset Button and LED Location Status Indicators: With the unit facing down and the base moved to the right as shown above, the XAP-1040 has four LEDs, positioned horizontally on the bottom, left side of the board. When viewed left to right, LEDs are as follows: 1) Bridge Mode (Green); 2) WLAN Status (Blue); 3) LAN Link/Activity (Amber); and 4) Power (Green).
Simply Connected Reset Button: The Reset button is used to clear the current settings of the XAP-1040 and restore factory default settings. To Restore the Default Settings: With the XAP-1040 powered on, press and hold the Reset button for 15 seconds. When the Power LED comes on again, release the reset button. The XAP-1040 will be set to factory defaults. CAUTION: Pressing and holding the Reset button will remove any custom configurations done to the XAP-1040.
XAP-1040 Quick Install Guide XAP-1040 Suggested Mounting Location Mounting the Access Point on a Wall or Pole The XAP-1040 can be mounted directly to a wall or pole using the included mounting bracket. Once the mounting location has been selected, installation is as simple as plugging the Ethernet cable into the RJ-45 connector and then mounting the access point directly to the wall or pole as shown in the diagram below: The XAP-1040 mount assembles as show above.
Simply Connected RJ-45 Connector Weather Resistant Gland assembly NOTE: Category-5, super Category-5 or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP) cables can be used. For best results, it is recommended that Category-6 shielded twisted pair be used to ensure stable data transmission at highest data rates. Once the RJ45 Connector Gland has been assembled and the Ethernet Cable has been terminated, the cable can now be plugged into the XAP-1040.
XAP-1040 Quick Install Guide Connecting to the Internet Source NOTE: If your Internet source (Router or Switch) is a POE enabled device and connected via POE, it can be plugged directly into the access point without the need to run a separate POE injector.
Simply Connected CONFIGURATION NOTE: Configuring the Luxul AP with non-Luxul routers may require your computer’s IP address to be changed. The Luxul XAP-1040 default IP addresss is 192.168.0.14. If the IP address of your router is not set to the 192.168.0.X network, a temporary static IP address must be set on the computer being used for configuration. To do so, set the IP address of the computer to the 192.168.0.X range and then use the default IP address of your XAP-1040 (192.168.0.
XAP-1040 Quick Install Guide Login to the XAP-1040 Wireless Access Point with the following steps: a. Be sure the XAP-1040 is properly installed and powered on b. Open your Web Browser, and enter http://192.168.0.14. The login window appears as shown below: c. Enter the user name and password (default user name is ”admin” and default password is “admin”), and then click “OK” to login to the Quick Setup window. Quick Setup For configuration instructions download the XAP-1040 User Guide from luxul.com.
Simply Connected WARNINGS AND SAFETY INFORMATION Verify that the electrical circuits have appropriate grounding and overload protection. Attach only approved power cords to the device. Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications. DO NOT install in or near hot or humid places, such as a kitchen or bathroom. Take care to minimize exposure to excessive heat or moisture.
XAP-1040 Quick Install Guide Health and Safety Recommendations Warnings for the use of Wireless Devices: Please observe all warning notices with regard to the usage of wireless devices Potentially Hazardous Atmospheres: You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).
Simply Connected FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CE Declaration of Conformity: Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that this Luxul XAP-1040 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For a copy of this report send a self addressed stamped envelope to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020. Industry Canada (RSS-Gen Issue 4) This device complies with Industry Canada licence-exempt RSS standard(s).