Simply Connected Quick Install Guide XAP-1230 High Power Wireless 300N Commercial Grade Access Point Use the XAP-1230 to: Deliver Broader Wi-Fi Coverage and Eliminate Client Device Roaming Issues with Fewer APs Improve Data Rates with Multi-Stream Wireless 802.
XAP-1230 Quick Install Guide Quick Install Guide Model Number: XAP-1230 High Power Wireless 300N Commercial Grade Access Point FCC ID: W59XAP1230A IC: 8584A-XAP1230 © 2014 Luxul. All Rights Reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design.
Simply Connected PACKAGE CONTENTS One: XAP-1230 Wireless Access Point Two: 5dBi Dipole Antennas One: PoE Injector and Power Cord One: Ethernet Cables Four: Rubber Feet One: Quick Install Guide NOTE: If any of the listed items are missing or damaged, please contact the reseller from whom you purchased for return/replacement. HARDWARE DESCRIPTION The XAP-1230 high powered access point is designed for optimal performance as well as for simple and efficient installation and setup.
XAP-1230 Quick Install Guide XAP-1230 LED Indicators Indicator Name Description Power On The power is on Off No power, check power connections On There is an active Ethernet connection Flashing Indicates Ethernet activity Off There is no active Ethernet connection On The wireless radio is active and wireless access is enabled Off The wireless radio is not active and wireless access is disabled On Bridge is connected Flashing Bridge Mode enabled but not connected Off The AP is in defa
Simply Connected Back Panel The back of the XAP-1230 provides two SMA antenna connectors and one RJ-45 connection that is used to deliver both power and data to the access point. RESET XAP-1230 Rear Panel Reset Button: The Reset button is used to clear the current settings of the XAP-1230 and restore factory default settings. To Restore the Default Settings: With the XAP-1230 powered on, press and hold the Reset button for 15 seconds.
XAP-1230 Quick Install Guide XAP-1230 INSTALLATION Access Point Placement This XAP-1230 uses omni-directional antennas designed to provide 360 degrees of coverage. For maximum efficiency, it should be placed as close as possible in the center of the area in which you would like to provide coverage. XAP-1230 Coverage Pattern Mounting the Access Point on a Wall The XAP-1230 can be mounted directly to a wall. It can also be placed on a desktop, shelf, or other flat surface.
Simply Connected Install Included Rubber Feet in the Impressions in the bottom of the XAP-1230 Connecting the Ethernet Cable With the XAP-1230 properly mounted and the Antennas installed, you can now plug the Ethernet Cable into the RJ-45 connector. NOTE: Category-5, super Category-5 or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP) cables can be used. For best results, it is recommended that Category-6 shielded twisted pair be used to ensure stable data transmission at highest data rates.
XAP-1230 Quick Install Guide From your Router or Switch POE Injector Power Source DATA IN DATA & PWR OUT XAP-1230 The PoE Injector combines power and data to the XAP-1230 CAUTION: Because the XAP-1230 is a High-Powered access point it is normal for it to be warm to the touch NOTE: The XAP-1230 is designed to work with any 802.3at power source. NOTE: The XAP-1230 can also be powered by direct AC power. Contact Luxul to purchase an AC Power Adapter.
Simply Connected the computer to be used for configuration. To do so, set the IP address of the computer to the 192.168.0.X range and then use the default IP address of your XAP-1230 as the Gateway/Router. Once configured, set the computer IP configuration back to “Obtain Automatically/DHCP.” NOTE: Go to http://luxul.com/how-to-videos for videos about changing the IP address of your Operating System.
XAP-1230 Quick Install Guide REGULATORY COMPLIANCE The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. This equipment also complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
Simply Connected Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the radio. FCC Statement—Wireless FCC 2.4GHz 802.11bgn This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Industry Canada (RSS-Gen Issue 2) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareilsradio exempts de licence.
