User guide

ManualsBrandsLuxul ManualsRoutersXMS-1024P

Simply Connected

Use the XMS-1024P to:



Cost-effectively Add 802.3af/at PoE Capability to Your

Network



Deliver Power and Data for up to 24 PoE-Enabled Network

Devices with a Maximum Output of 320 Watts



Simplify PoE Device Installation, Including IP Sercurity

Cameras, VoIP Devices, and Wireless AP’s



Future Proof Your Network with Gigabit Speeds

(10X Performance of Fast Ethernet)



Optimize and Protect Your Network with Advanced

VLAN, QoS and Network Security Features

Quick Install Guide

XMS-1024P

24-Port Gigabit Ethernet

Managed PoE Switch

Summary of content (8 pages)

PAGE 1
Simply Connected Quick Install Guide XMS-1024P 24-Port Gigabit Ethernet Managed PoE Switch Use the XMS-1024P to: Cost-effectively Add 802.
PAGE 2
XMS-1024P Quick Install Guide Quick Install Guide Model Number: XMS-1024P 24-Port Gigabit Ethernet Managed PoE Switch © 2014 Luxul. All Rights Reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Luxul. The material in this manual is subject to change without notice. Luxul reserves the right to make changes to any product to improve reliability, function, or design.
PAGE 3
Simply Connected PACKAGE CONTENTS The following items are included in the box: XMS-1024P 24-Port Gigabit Ethernet Managed PoE Switch Power Cord Two L-shaped rack mounting brackets and screws Four rubber pads Quick Installation Guide RJ45 to Serial Console Cable If any of the listed items are missing or damaged, please contact the Distributor from whom you purchased for return/replacement.
PAGE 4
XMS-1024P Quick Install Guide LED Indicators LED indicators show the working status of the switch. The following table describes the LED functionality: Indicator Name Description Power On This LED indicates that there is power to the XMS-1024P Off If LED is off, check the power connection on the back of the unit. Flashing Indicates that the XMS-1024P is running normally. On Indicates a malfunction. Contact technical support.
PAGE 5
Simply Connected Rear Panel A 0Hz 5.0 V-50/6 100-240 XMS-1024P Rear Panel View Power Input: Please use the included power cable PREPARING FOR INSTALLATION System Requirements Ethernet Cables to connect the XMS-1024P to Ethernet enabled devices Computer equipped with a Web browser. Supported Web browser versions include Microsoft I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6 and up. The Web browser is used to configure the XMS-1024P. Power must be AC 100-240V~ 5.
PAGE 6
XMS-1024P Quick Install Guide XMS-1024P INSTALLATION Installing the XMS-1024P in a Rack The XMS-1024P can easily be installed in a standard 19” rack. The XMS-1024P includes two mounting ears for installing and stabilizing the switch. For attaching the mounting ears and installing the switch within a rack, please refer to the following illustration: Rack-Mounting the XMS-1024P Using the included screws, attach the mounting ears to each side of the switch.
PAGE 7
Simply Connected For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP) should be used. NOTE: For best results, it is recommended that Category-6 shielded twisted pair be used to ensure stable data transmission at 1000 Mbps. Optical fiber/cable should be selected based on the wavelength of the SFP optical module to be used. Make sure only one Uplink channel exists between switches or between the XMS1024P and a router.
PAGE 8
ADVANCED SETTINGS For login and advanced settings information go to luxul.com WARNINGS AND SAFETY INFORMATION ff Verify that the electrical circuits have appropriate grounding and overload protection. ff Attach only approved power cords to the device. ff Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications. ff The XMS-1024P is designed for indoor use only. DO NOT place this outdoors.