Flarm LED indicator Version 1.0 LXNAV d.o.o. • Kidričeva 24a, 3000 Celje, Slovenia • tel +386 592 33 400 fax +386 599 33 522 info@lxnav.com • www.lxnav.
FlarmLed display Version 1.0 1 Important Notices 1.1 2 3 August 2013 3 Limited Warranty 3 Packing Lists Basics 4 5 3.1 LXNAV FlarmLed display at a Glance 3.1.1 LXNAV FlarmLed display features 3.1.2 Interfaces 3.1.3 Technical Data 4 System Description 6 4.1 Description of Flarm Led Display 4.1.1 Status Leds 4.1.2 Horizontal direction LEDs 4.1.3 Vertical direction LEDs 4.1.4 Push Button 4.2 Normal operation 4.2.1 Near mode 4.3 Powering up FlarmLed display 4.4 Setting up FlarmLed display 4.
FlarmLed display Version 1.0 1 August 2013 Important Notices The LXNAV FlarmLed display is designed for VFR use only as an aid to prudent navigation. All information is presented for reference only. Information in this document is subject to change without notice. LXNAV reserves the right to change or improve their products and to make changes in the content of this material without obligation to notify any person or organisation of such changes or improvements.
FlarmLed display Version 1.
FlarmLed display Version 1.0 3 August 2013 Basics 3.1 LXNAV FlarmLed display at a Glance FlarmLed display Flarm® compatible device, able to indicate horizontal and vertical direction of a threat. Nearby traffic is displayed visually and acustically. It’s extremely small size, low power consumption, and has very bright bicolor LED’s. 3.1.1 • • • • • • extremely bright bicolor LEDs pushbutton, to adjust beep volume nearmode function adjustable baudrate slave mode Low current consumption 3.1.
FlarmLed display Version 1.0 4 August 2013 System Description 4.1 Description of Flarm Led Display Flarm • • • • • 4.1.1 led consist of 5 main parts: Status LEDs Horizontal direction LEDs Vertical direction LEDs Push button Beeper Status Leds Status LEDs indicates if flarm receiver receives any data, transmits data and GPS status.
FlarmLed display Version 1.0 4.1.3 August 2013 Vertical direction LEDs 5 LEDs are describing vertical angle of threat divided by 14° 4.1.4 Push Button With push button we can adjust volume of beep, turning on/off near mode or adjust initial settings of FlarmLed display. 4.2 Normal operation In normal operation with short press, we can cycle between three different volumes (Low, Medium and High). With long press, is enabled or disabled near mode.
FlarmLed display Version 1.0 August 2013 4.4 Setting up FlarmLed display If we hold push button, during power on, LXNAV FlarmLed will go in setup mode, where is possible to adjust following settings: • Communication speed • Master/Slave mode Yellow led indicates mode that we are setting, Red leds indicates setting of each mode.
FlarmLed display Version 1.
FlarmLed display Version 1.0 August 2013 B2 Indication: Invalid IGC feature licence. Operation possible B3 Indication: Invalid AUD feature licence. Operation possible B4 Indication: Invalid ENL feature licence. Operation possible B5 Indication: Invalid RFB feature licence. Operation possible B6 Indication: Invalid TIS feature licence. Operation possible 100 Indication: Generic error. Operation possible 101 Indication: Flash File System error.
FlarmLed display Version 1.0 August 2013 4.6 Wiring 4.6.1 FlarmLed pinout Pin number 4.6.2 Description 1 N.C. 2 (output) Transmit from LXNAV FLARM LED RS232 Level 3 (input) Receive to LXNAV FLARM LED RS232 Level 4 Ground 5 3.3V power supply (input) 6 N.C.
FlarmLed display Version 1.0 August 2013 4.
FlarmLed display Version 1.