CD-1 Compact Disc Player Owners Manual -1-
Table of Contents WARNINGS.........................................................................................................................................3 Explanation of graphical symbols .....................................................................................................3 Important safety instructions.............................................................................................................4 Unpacking the CD-1 ....................................................
WARNINGS CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Important safety instructions 1:Read these instructions. 2:Keep these instructions. 3:Heed all warnings. 4:Follow all instructions. 5:Do not use this apparatus near water. 6:Clean only with a dry cloth. 7:Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8:Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat. 9:Do not defeat the safety purpose of the grounding-type plug.
Accessories You should find the following in the accessory kit: 1. 2. 3. 4. 5. One mains cord This manual Customer registration form Remote control RS232 Cable for firmware upgrade from a PC Operating voltage The CD-1 is selectable to one of the following power ratings: 100V-120V~ at 50-60Hz with a power rating of 20W 220V-240V~ at 50-60Hz with a power rating of 20W WARNING: Connect the power input only to the AC source printed on the label and the setting shown on the voltage selector switch.
Introduction Lyngdorf CD-1 is an audio optimized upsampling Compact Disc Player with low jitter clock and a High Performance DAC section. Features: • Audio optimized CD transport mechanism with low jitter clock • Linear Low Noise power supply based on Holmgren Transformer technology. • 3 digital outputs: AES, SPDIF, Toslink - selectable sample rate 44.1/48/96/192 kHz. • Transformer coupled digital interconnects (eliminates ground loops).
Front panel Fig 1: CD-1 front panel Front panel controls and functions The buttons/controls on the front panel of the CD-1 can all be used either by directly pressing them on the front panel or by operating the similar keys on the included remote control. All keys on the front panel except the Mains switch (1) can be found on the remote control. Additional buttons on the remote control include the following: random, repeat, A/B and the digits 0-9.
itself at the start of the selected track but it remains in pause mode until the play/pause button is pressed again. (7) Stop Pressing stop during play or pause mode will stop the CD. (8 & 9) Skip / Scan Pressing briefly on the Left |<< Skip/Scan button or turning the skip wheel left will restart the current track or, if currently playing within the first two seconds of the current track, skip to the previous track.
A-B Repeat mode is indicated in the lower left-hand corner of the display. When [A] time has been set and CD-1 is waiting for [B] time, the symbol “A ” will be displayed. Once [B] time has been selected and the CD-1 is playing in A-B Repeat mode, the symbol will be changed to “AB”. Random Play mode When the ‘Random’ button is pressed on the remote control or Random mode is activated in the menu, the Random Play mode is entered and CD-1 creates a random play list.
Rear panel Fig 2: CD-1 rear panel.
Remote Control The remote control is used to access the menu system and replicate the buttons directly accessible on the front panel. The four buttons used for selecting which device to control are described below. To control the CD player the CD key should be pressed, please note the volume and mute buttons will still work with a Lyngdorf Amplifier, even in CD mode. • Amp – Selects the remote for operation with a Lyngdorf Amplifier.
• Standby – The standby button toggles the CD-1 between active “On” and standby mode. • Numbered buttons 0-9 – The numeric keys allow direct selection and input of tracks on CD. • Left/Right < > – Allows you to Skip tracks and scroll through the menu functions. • Enter – Allows you to confirm actions in menu mode. When not in menu mode, this button also functions like the play/pause button. • Skip/Scan |<< >>| - Allows you to Skip to specific tracks.
Main Display The Main Display on the front panel of the CD-1 is the users feedback of all functionality and current status of the CD-1. When the Player is powered up the Main display screen shows the current firmware version: LYNGDORF CD-1 Version: 1.0 If no disc has been inserted, the following text will appear: LYNGDORF CD-1 No Disc When opening the tray, the display will indicate this. LYNGDORF CD-1 Opening The next screen will show the ‘Tray Open’ ready for you to carefully insert a compact disc.
When skipping between tracks the time will disappear and be displayed again once the requested track has been found. Playing 6 of 11 If you press pause the CD-1 will display the time at which the track has been paused. Pause 6 of 11 0:09 Pressing A/B on the remote control will show ‘A’ in the bottom left hand corner of the display, this indicates that the start time has been selected, and the CD-1 is now waiting for the stop time.
Menu System Display The Menu system shown in the display of CD-1 is the user’s feedback of all functionality in the menu and sub menu system. When entering menu mode, the first item is shown as: Main Menu CD-1 The user can browse through the menu items using the right and left arrows or the skip wheel. The available menu items are:
Selects the address used for the CD-1 when communicating with PC’s or other devices via the RS-232 port. Comm Current: 3 Address New: 11 < Comm Speed > Selects the speed used when communicating with PC’s or other devices via the RS-232 port. Comm Current: 9600 Speed New: 57600 < Remote Control > Disables or enables the IR remote control.
Firmware Lyngdorf Audio supplies a free PC tool for upgrading the firmware of the CD-1. The latest revision of the tool as well as the firmware can be downloaded from www.Lyngdorf.com. Connectors Mains Connector Mains voltage to the CD-1 is applied via an IEC320 type connector. The supplied cable with safety ground should be used to connect the CD-1 to a mains outlet. WARNING: Connect the power input only to the AC source printed on the label and the setting shown on the voltage selector switch.
Digital outputs RCA output (SPDIF): Shell: Chassis and Ground Pin: Hot (+) XLR output (AES): Pin 1: Chassis and Ground Pin 2: Hot (+) Pin 3: Cold (-) Shell: Chassis and Ground Toslink Cleaning and maintenance Always unplug the unit from the electrical outlet before cleaning. This unit does not require any regular maintenance except to keep its exterior clean. Simply wipe its exterior with a clean soft cloth.
Technical specifications All audio measurements, except frequency response, are measured with a 20KHz lowpass filter in accordance with AES-17. Measured on Unbalanced outputs - RCA (phono). Audio Parameter Frequency response L/R Value +/- 0.
Mechanical Parameter Width Depth Value 450mm (17.72") 352 mm(13,86 ") Depth 357 mm(14,06 ") Height Height Net weight Shipping weight 89 mm(3,5039 ") 100 mm(3,9370 ") 7.1 Kg (1.65 lbs) 9.1 Kg (6.06 lbs) Note including skip wheel, excluding connectors including skip wheel, including connectors Excluding feet. Including feet.
Technical assistance If you have any problems with or questions regarding your Lyngdorf Audio product, please contact Lyngdorf Audio or your nearest representative. Support Please check the Lyngdorf Audio Denmark website under “Support” for latest version of control software, newest version of this document and “Questions and Answers”. Lyngdorf Audio Denmark Nordhavnsvej 12 DK7800 Skive Denmark E-mail: Web: info@lyngdorf.com http://www.lyngdorf.