MOM FRIENDLY. DAD READY.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS IMPORTANT SAFEGUARDS WARNING Two to three people are needed to set up the island. Failure to do so may result in injury. WARNING Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. To reduce the risk of fire, electrical shock or personal injury follow the instruction contained in this guide carefully. Do not omit any steps. Never attempt to lift the island by the counter top as serious damage may occur.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Congratulations on your purchase of the SEDONA by LYNXTM island package cooking center. The fully featured premium outdoor kitchen can be created in no time at all. The Mom Friendly, Dad ReadyTM cooking products are designed with the family in mind. The grills are crafted by Lynx Grill Specialists at our factory in Southern California.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS PART NUMBER 4 | DESCRIPTION PHOTO SPECIFICATIONS 1 (14044) TANK RETAINING WASHER 2 (14014) TRANSFORMER /BATTERY MOUNTING SCREWS 3 (14009) SIDE BURNER MOUNTING HEX NUT 4 (32730) SIDE BURNER MOUNTING SCREW 5 (14012) ACCESS DOOR FRAME MOUNTING SCREWS 6 (14030) HEX BOLT 7 (34264) TANK RETAINER FINGER SCREW 8 (34396) ADJUSTABLE FEET 6 EA. 9 (34395) WING NUT 3/8-16 10 EA. 10 (34397) WING BOLT 3/8-16 x 2 4 EA.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 1 Unpacking the Crate Using a manual or power Philips head screwdriver, remove all of the screws used to secure the top cover of the crate. Remove the island bottom, rear, front and two side panels from within the crate. We recommend 2 to 3 people perform setup operations. TEAM LIFT FOR YOUR SAFETY Step 2 Position and Level the Base Place the island base on a level surface in it’s final location and proceed to level it in all directions.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 3 Assembling the Rear & Side Panels Assemble the rear panel to the bottom panel by placing the corners of the back panel on top of the bottom panel corners and push them firmly together. Step 3A Insert Back Panel Onto Base While one person holds the rear panel in place, attach a side panel to the rear panel loosely using the 2 wing-nuts (Part No. 9), turned in about 4 full turns.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 4 Assemble the Front Panel With one person holding the rear and side panel in place, assemble the front panel to the bottom by placing the front panel corners on top of the bottom panel corners and pushing them firmly together Tilt the front edge of the side panel away from the bottom panel to allow the front panel mounting brackets to pass by threaded mounting screws on the side panel.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 5 Overview of the Island’s Electrical System Now that the island wall assembly is complete, familiarize yourself with the location of the electrical outlets. The electric outlets come pre-wired from the factory. The photo below shows the position of the 110 VAC GFCI outlet on the left rear wall, the back panel center outlet for the refrigerator and grill power supply, and the combination USB charging station and 110 VAC power outlet on the right.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 6 Mounting the Transformer Locate the 4 transformer mounting screws (Part No. 2) and the transformer/battery bracket. The transformers are found in the packaging inside the grill and side burner packaging. Mount the transformer on the rear panel support frame near the rear panel outlet using the pre-drilled holes provided. Install the side burner battery bracket (not shown) below the transformer in the same manner (see page 13).
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 9 Install the Side Burner We recommend a qualified, trained gas service technician perform all pipe fitting and gas leak test procedures prior to installing the refrigerator. Once installed there will be limited access to the gas piping. Before installing the side burner, familiarize yourself with the illustration on the next page. Wrap the side burner manifold threads with Teflon tape, see Fig. 1 on page 11.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 11 Making the Connections We recommend a qualified, trained gas service technician perform all pipe fitting procedures and conduct a gas leak test prior to installing the refrigerator. Once installed there will be limited access to the gas piping. Working from the refrigerator cutout, find the stainless steel flexible hose from the side burner. Remove the 1/2” fitting from the flexible hose and wrap the fitting with Teflon tape.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS Step 12 Installing the LP Tank The LP Tank retention device can be secured to the door frame with two bolts (Part No. 6) and washers (Part No. 1). The LP tank is rested in the retainer and the finger screws (Part No. 7) are tightened at the base of the tank securing it into position. Connect the hose and regulator to the LP cylinder. Make sure all of the burner knobs are in the OFF position.
SEDONA ISLAND ASSEMBLY INSTRUCTIONS See Step 9 Make the electrical connections as shown below, then plug the transformer into the electrical outlet on the rear panel.
Sedona By Lynx Island Package Limited Warranty I. Limited Warranty – Grill, Side-Burner, Doors, Drawers, and Refrigerator For the warranty on the individual stainless steel island components, please see the warranties in their product Care & Use Manuals. II.
SEDONA ISLANDS Replacement parts listS L1600G PART NO. 34312 34297 34320 34321 34324 34310 34332 34333 80763 90216 QTY.
SEDONA ISLANDS Replacement parts listS L2600G PART NO. 34296 34297 34304 34305 34308 34310 34332 34333 80761 90216 QTY.
notes SEDONA Island Assembly Instructions | 17
notes 18 | SEDONA Island Assembly Instructions
Lynx Professional Grills 5895 Rickenbacker Rd. Commerce, CA 90040 Service: (888) Buy-Lynx (888-289-5969) Fax: (323) 838-1778 www.Lynxgrills.