Manual

CARE & USE/INSTALLATION
|
31
• The four digit PIN can be located on the rating plate.
This is your personal number that insures that no
version of the SmartGrill by Lynx™ app save yours is
able to control your SmartGrill by Lynx™.
• Input the SmartGrill by Lynx™’s Serial Number.
This serial number can be found on the last page
of this Care & Use manual or on the underside of
the SmartGrill by Lynx™’s drip tray. (See INDEX:
“Downloading and installing your SmartGrill by
Lynx™ App”.)
• Once the app has been connected to the SmartGrill by
Lynx™, the app will open up the “Grill Status” page.
Click the light bulb labeled “Support” at the bottom of
the screen.
• Click “Wi-Fi” settings
• You will see a list of networks available for your SmartGrill
by Lynx™ Choose your home network.
• Depending on your security settings, you may need
to enter your home network’s password to allow the
SmartGrill by Lynx™ to access it.
• Once the SmartGrill by Lynx™ has successfully accessed
your home network, you will receive a “Success”
message.
Once you have successfully connected the SmartGrill by
Lynx™ to your home network, you may have to return
to your device’s “Settings” app and reconnect with your
home network.
FACTORY RESET
If needed, the Wi-Fi setting in your grill can be reset. Press
the power button to turn the grill off. Then press and hold
the Power button in the OFF position for 15 seconds.
If a factory reset is done, you will have to setup your Wi-Fi
connection again. Please refer to the Quick Start Guide for
setup procedure.
GRILL WON’T LIGHT
First, confirm that the grill is getting electricity by checking
the lights that surround the dials on the front panel of your
SmartGrill by Lynx™.
Check the Igniters
Your Lynx SmartGrill by Lynx™ uses an electric ignition
system that does not spark. Instead the igniters will glow
constantly when a control knob is turned on. If one of your
igniters is not working, SmartGrill will say or send you a
text of "Igniter Failure".
• Ensure that all burners are set to OFF
• Remove a cooking grate so you can clearly see the
igniter.
• Turn the burner knob ON (two full rotations clockwise)
and wait approximately one minute for the igniter to
glow.
• Check all igniters. If they do not glow, call Lynx for service
at 888-289-5969.
Check the Burners
If your burner fails to ignite, SmartGrill will text or say
"Burner <N> has no flame." If the burner has no flame,
SmartGrill will turn off the gas to that burner.
Be careful! If the burner fails to ignite, wait five minutes
before attempting to ignite other burners!
Check to make sure your gas line is connected and the
shut off valve is turned on. Re-check fuel connections for
leaks and ensure the supply is of the correct type and is of
adequate pressure. (See INDEX: “Leak Test Procedure” for
further details.)
If you know you are getting gas, wait for any gas to
dissipate and remove the burner and check for gas
blockages.
Replace any damaged supply lines.
• Check the regulator.
Make sure that the regulator and hose assembly is the one
designed for and supplied with your Lynx grill and that it
is correctly set up for the type of fuel you are using. (See
INDEX: “Regulator Conversion” for further details.)
The hose and regulator provided by Lynx Grills must be
used if your grill is set up for use with a liquid propane gas
cylinder.
Check that there is no physical pressure being applied
to the regulator attached to the back of the grill. The
regulator contains a flexible diaphragm and should not be
allowed to touch the grill body or its surroundings.
• Check for obstructions.
Ensure that the burners and the drip tray are clean and free
from obstructions.
Liquid Propane Units:
TROUBLESHOOTING ...continued