User Manual/ Installation Instructions Model: L24BF Lynx Professional Grills 5895 Rickenbacker Rd., Commerce CA 90040 Service: (888)289-5969 Tel: (323) 838-1770 Fax: (323) 838-1778 WWW.Lynxgrills.
IN D O R T C U Customer Service. Congratulations on your purchase of a Lynx residential refrigeration product. Lynx has taken its expertise and experience into creating the highest quality and most innovative residential products on the market. Lynx’s product offering gives you the opportunity to enjoy the functionality and user friendliness outdoors, or in just about any room of your home.
TABLE OF CONTENTS INTRODUCTION…………………………………………………………………………………….…….. 1 PLEASE RECORD YOUR MODEL’S INFORMATION…………………………………….…….…… 1 WARRANTY REGISTRATION CARD…………………………………………………………………... 1 TABLE OF CONTENTS……………………………………………………………………………….….. 2 GENERAL PRECAUTIONS…………………………………………………………………...…….…… 3 INSTALLATION INSTRUCTIONS………………………………………………………………………. 3 FIGURE 1 SPECIFICATION DRAWING………………………………………………..……………… 4 PREPARING THE SPACE………………………………………………………………..……………...
G R N E P L A U C S IO T DANGER Risk of child entrapment, before you throw away your old refrigerator or freezer, take off the doors and leave shelves in place so that children may not easily climb inside. DANGER Altering, cutting of the power cord, or removal of the power cord, removal of power plug, or direct wiring can cause serious injury, fire and/or loss of property and/or life and will void the warranty.
26 7/8” 24” 22 1/16” 35 1/16” Max. 34 5/16 Min. Figure 1.
R P G IN A E H T C S Make sure that the opening where the unit is to be installed is properly prepared. Refer to Figure 1 to ensure the space dimensions and electrical service are correct for the models to be installed. CAUTION If unit is being installed under a counter top it is required that the counter top be supported by structure other than the refrigerated cabinet to prevent damage to the counter top. IMPORTANT NOTE: Allow 25” clearance in front of the unit for full door swing and shelf pull out.
Figure 2. TWO-DRAWER ANTI-TIP LAYOUT installation, the unit must be secured in place with the anti-tip brackets provided with the unit. A set of metal anti-tip brackets are supplied with the unit. The anti-tip brackets, when properly installed should secure the rear legs and prevent the unit from tipping forward. WARNING Unit may tip forward when loaded racks/shelves are pulled to open position.
IN L A T S O IMPORTANT NOTE: If installing on a concrete floor, concrete fasteners are required and not included with the anti-tip kit. CAUTION Any finished flooring should be protected with appropriate material to avoid damage from moving the unit. If unit has been laid on its back or sides, place unit upright and allow minimum of 24 hours before connecting power. 1. Plug the unit into the 15 amp grounded GFI outlet located in the installation opening.
O T A L P E S IN When the unit is secured in place, install the louvered toe plate. Secure louvered toe plate by snapping the latch into the latch catch on the unit. Refer to Figure 3 TOE-PLATE INSTALLATION ILLUSTRATION Figure 3. TOE PLATE INSTALLATION. CAUTION The louvered toe plate must be removable for servicing. The floor cannot interfere with removal. The louvered sections of the toe plate must not be covered or obstructed so as to prevent proper air circulation.
SHELVING IMPORTANT NOTE: Interior louver openings and fan guard openings should never be obstructed to achieve maximum performance. The single door unit comes standard with black vinyl coated adjustable full extention pullout shelves. Adjusting Full Extention Shelving 1. Pull the shelf out to its furthest position. Locate the tabs in the middle of both extenders (Figure 4), Lift on tab up while pushing the opposite tab down and pull shelf out. 2. Repositon each bracket separately.
DOOR LOCK See Figure 6 for door lock and latch bracket details. DOOR HINGE REVERSAL Procedure for switching direction of door swing using Left Hand Hinge Kit Part No. 90197. 1. Support the door and remove the hinge pin. 2. Pull the door to the side and lower the door from the upper hinge pin and bracket 3. Remove the Top and Bottom Cabinet Hinge Brackets and save the screws for later 4.
Step 8: Step 9: Step 10: 7. Remove the Lynx name plate from the Door using a Plastic Putty Knife. Install the new Lynx nameplate (included) 8. Insert bearing into Top Door Hnge Bracket 9. Insert V-Block into Bottom Door Hinge Bracket, attach with E-Clip 10. Attach the Top and Bottom Door Hinge and Push Plunger using screw removed in Step 6 11. Place Lower V-Block into Lower Cabinet Hinge with notche parallel to cabinet 12. Lift the Door Assembly and insert top pin into bearing.
the top and cause the refrigeration system to run longer. Loading Product IMPORTANT NOTE: Before storing perishables, allow unit to run for a minimum of 24 hours to allow temperature stabilization after start-up. When loading items into unit, do not block internal louvers and fan guard openings or performance will be decreased. Step 12 Temperature Control Panel The controller is located inside of the unit. The display will read OFF when unit off and will show temperature when unit is on.
M E T R P U A O C N L .
IMPORTANT NOTE: The controller has been programmed to only allow a temperature adjustment within a specified range (see chart below for the specified range of 33°F to 43°F.
C G IN K E H O R P D M T U A E To accurately check the temperature of the product stored in a refrigerated compartment, insert an accurate thermometer into a plastic (non-breakable) bottle, partially filled with water. Tighten the bottle cap securely. Place the bottle in the desired area for 24 hours. Refrain from opening the unit during the testing period. After 24 hours, check the temperature of the water. Adjust the control settings if necessary and re-test.
TROUBLESHOOTING BEFORE CALLING FOR SERVICE If the unit appears to be malfunctioning, read through NORMAL OPERATION first. If the problem persists, check the TROUBLESHOOTING GUIDE. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem could be something, which can be solved without a service call.
The refrigerated compartment is warmer than usual Is your control set properly? Is the light staying on? Is your condenser area clean and free of obstructions? Has the door been open for a long time or more frequent door openings occurred? Are the internal louvers and fan guard openings obstructed? Has warm product just been placed in the cabinet? The refrigerated compartment is colder than usual Is your control set properly? Is your door closing and sealing properly? Is the ambient temper
R A W N Y T One Year Parts and Labor Warranty: For one year from the date of original purchase, within the United States and Canada, when used and maintained according to instructions, Lynx Grills warranty covers all parts and labor to repair or replace any part of the product, which proves to be defective in material and workmanship.
5895 Rickenbacker Road ● Commerce, CA 90040 ● 888-289-5969 ● Fax 323-838-1778 ● www.lynxgrills.
