MAKE THE MOST OF YOUR CARE & USE/INSTALLATION
WARNINGS WARNING • Never use dented, rusty or damaged propane cylinders. Never store additional or empty propane cylinders in the grill cabinet or in the vicinity of this or any other appliance. Do not store propane cylinders indoors or on their sides. • Children should never be left alone or unattended in an area where a grill is located. Place your grill well away from areas where children play.
WARNINGS WARNING READ THIS MANUAL CAREFULLY and completely before using your grill to reduce the risk of: 1. 2. 3. 4. Fire Burn hazard, personal injury or property damage Ruined steaks or other unpleasant cooking experiences Unapproved installation or servicing. THIS PRODUCT IS DESIGNED FOR OUTDOOR USE ONLY. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read this manual thoroughly before installation, use, or servicing of this product.
WARNINGS WARNING 1. Always maintain the required clearances from combustible construction as detailed. The grill is designed for outdoor use only. Never use in a garage, building, shed, breezeway or other enclosed area. This grill shall not be used under any unprotected overhead combustible construction. 2. Gas grills are not design certified for and are not to be installed in or on recreational vehicles, portable trailers, boats or any other moving installation. 3.
TABLE OF CONTENTS BEFORE YOU START 6 If Shipment Arrives Damaged 6 Important Notes 6 SPECIFICATIONS & INSTALLATION 8 UNPACKING & ASSEMBLY 16 GAS CONNECTIONS 18 Natural Gas 18 LP Gas 19 Gas Conversion Kits 20 ELECTRICAL CONNECTIONS 22 FINAL CHECKS 23 Leak Testing 23 CHECKLIST BEFORE EACH USE 24 A MESSAGE TO OUR CUSTOMERS 25 IMPORTANT SAFETY PRECAUTIONS 25 GRILLING IN WINDY CONDITIONS 26 USING YOUR GRILL 26 Pre-Grill Checklist 27 Lighting your Grill 27 Basic Grilling 29
BEFORE YOU START WARNING Installation into a combustible enclosure requires an insulated jacket accessory. DO NOT REMOVE BRACKET OR INSTALL UNIT without use of the insulated jacket. Doing so may result in a fire, injury or property damage. Bracket must be removed to complete install with insulated jacket. Insulated jackets may be ordered at parts@middlebyresidential.com or phone 888-845-4641 press 1. Please have grill model and serial available when ordering.
BEFORE YOU START ...continued BUILT-IN INSTALLATIONS This built-in grill is designed for easy installation into masonry enclosures. NOTE: Built-in grills are intended either for installation in a built-in enclosure constructed of non-combustible materials or for an installation in a built in enclosure constructed of combustible material when installed with a insulating jacket).
SPECIFICATIONS & INSTALLATION The guides, measurements and dimensions detailed below are designated to assist you with planning your outdoor kitchen. NOTE: Due to continuing product innovation, specifications are subject to change without notice. IMPORTANT: Please reference the Care & Use / Installation manual for details on gas plumbing requirements, electrical specifications and the proper installation of your outdoor kitchen equipment. This manual can be downloaded from our website at www.vikingrange.com.
SPECIFICATIONS & INSTALLATION L15ICE/LMWINE/LM15REF OUTDOOR ICE AND REFRIGERATION MODEL A B C D LM15REFL/R 15.00 34.00 - 35.00 26.00 33.75 - 34.75 LM24REFL/R 24.00 34.00 - 35.00 26.00 33.75 - 34.75 LM24REFCL/CR 24.00 34.00 - 35.00 26.00 33.75 - 34.75 LM24BFL/R 24.00 34.00 - 35.00 26.00 33.75 - 34.75 LM24DWR 24.25 34.00 - 35.00 26.00 33.75 - 34.75 LMWINE 15.00 34.00 - 35.00 26.00 33.75 - 34.75 LM15ICE 15.00 34.00 - 35.00 24.00 33.75 - 34.
SPECIFICATIONS & INSTALLATION MODEL-SPECIFIC BTU OUTPUTS & MAX.
DIMENSIONS L27R L27TR 30” 30" (76.2 cm) 1¾” (4.4 cm) 233/16” " 253/16cm) (64.0 1/ 2" 14½” 14 (36.8 cm) 13/4" 10½” " 10 1/2cm) (26.7 11” (27.911" cm) 11” 11"(27.9 cm) 9” (22.9 cm) 9" /2”"(2.9 cm) 211/8 1- 3" 19” (48.3 " 211/2cm) 227/8” (58.1 25 3/cm) 8" 253/8” 7 (64.5 27 /cm) 8" REAR 1/ 2"(6.4 cm) 22½” MANIFOLD Rear Manifold LOCATION Location 3” (7.6 cm) L27TRF 52¾”55 (134.0 3/ 4" cm) 1/ 2" cm) 33½”36(85.1 27” (68.6 30" cm) 1/ 2" 14½” 14 (36.8 cm) 1¾” (4.4 cm) 13/ 4" 5715/16” (147.
DIMENSIONS L30R L30TR 30” 30" (76.2 cm) 1¾” (4.4 cm) 253/16” 253/16cm) " (64.0 1/ 2" 14½” 14 (36.8 cm) 13/4" 10½” " 10 1/2cm) (26.7 11” (27.911" cm) 11” 11"(27.9 cm) 9” (22.9 cm) 9" 21/2"(6.4 cm) 2½” 3" 21½” (54.6 " 211/2cm) 253/8” (26.7 25 3/cm) 8" 277/8” 7 (70.8 27 /cm) 8" REAR 1/ 2"(6.4 cm) 22½” MANIFOLD Rear Manifold LOCATION Location 3” (7.6 cm) L30TRF 55¾”55 (141.6 3/ 4" cm) 1/ 2" cm) 36½”36(92.7 30” (76.2 30" cm) 1/ 2" 14½” 14 (36.8 cm) 1¾” (4.4 cm) 13/ 4" 6011/16” (154.
DIMENSIONS L36R L36TRF 36” (91.4 cm) 23½” (59.7 cm) 147/8” (37.8 cm) 1¾” (4.4 cm) 97/8” (25.1 cm) 11” (27.9 cm) 11” (27.9 cm) 9” (22.9 cm) 11/8” (2.9 cm) 19” (48.3 cm) 227/8” (58.1 cm) 253/8” (64.5 cm) 2½” (6.4 cm) Rear Manifold Location 3” (7.6 cm) L36TRF 61¾” (108.0 cm) 42½” (91.4 cm) 36” (91.4 cm) 147/8” (37.8 cm) 1¾” (4.4 cm) 11” (27.9 cm) 36” (91.4 cm) 32” (81.3 cm) REAR CORD LOCATION 31/8” (7.9 cm) 35½” (90.2 cm) 26¾” (67.9 cm) 87/16" 5811/16” (149.1 cm) 50” GAS EXIT (127.
DIMENSIONS L42TR 42” (106.7 cm) 253/16” (64.0 253/cm) 16" 1¾” (4.4 cm) 11” (27.9 cm) 9” (22.9 cm) 2½” (6.4 cm) 1/ 2" 14½” 14 (36.8 cm) 13/4" 10½” " 10 1/2cm) (26.7 11” (27.911" cm) 3" 2½” (6.4 cm) Rear Manifold Location 21½” (54.6 cm) 253/8” 8" (64.53/cm) 277/8” 7 (70.8 cm) L42TRF 3” (7.6 cm) 67¾”55(172.1 3/ 4" cm) 1/ 2" cm) 48½”36(123.2 42” (106.7 30" cm) 1/ 2" 14½” 14 (36.8 cm) 1¾” (4.4 cm) 13/ 4" 6011/16” (154.1 11/ 16"cm) 8¾” 60 3 4" 8 /cm) (22.2 50” 50" (127.0 cm) 11” (27.
DIMENSIONS L54TR 54” (137.2 cm) 25½” (64.8 253/cm) 16" 1¾” (4.4 cm) 11” (27.9 cm) 9” (22.9 cm) 2½” (6.4 cm) 2½” (6.4 cm) Rear Manifold Location 1413/16” 1/ 2" 14 (37.6 cm) 13/4" 103/16” " 10 1/2cm) (25.9 11” (27.911" cm) 3" 21½” (54.6 cm) 253/8” 8" (26.73/cm) 277/8” 7 (70.8 cm) 3” (7.6 cm) L54TRF 79¾” (202.6 cm) 60½” (153.7 cm) 54” (137.2 cm) 1413/16” 141/2" (37.6 cm) 1¾” (4.4 cm) 13/ 4" 6011/16” (154.1 11/ 16"cm) 85/8” 60 4" 83/cm) (21.9 50” 50" (127.0 cm) 11” (27.911" cm) 36” (91.
UNPACKING & ASSEMBLY The grill arrives nearly ready to use and requires only minor assembly. surface, or wood slatted decks be cautious and move slowly or use a carpet dolly. By carefully following the uncrating and unpacking steps, you will improve your first experience with the grill. Failure to do so may damage the structure of the cart wyhich will not be covered under warranty. Shipping weight on smaller units is app. 300 pounds and larger units may weigh over 500 pounds.
UNPACKING & ASSEMBLY ...
GAS CONNECTIONS WARNING NEVER CONNECT A GAS LINE DIRECTLY TO THE GRILL. A PRESSURE REGULATOR MUST BE INSTALLED ON ALL GAS EQUIPMENT. ALL LOCAL CODES REQUIRE THAT THE PRESSURE REGULATOR SUPPLIED WITH YOUR GRILL IS USED. REMOVING OR FAILING TO INSTALL THE PRESSURE REGULATOR CAN RESULT IN FIRE AND SERIOUS PERSONAL INJURY AND WILL VOID THE WARRANTY. The grill is factory set to use either propane (LP) or natural gas (NAT). It is critical that the gas you use matches that which the grill was set up for.
GAS CONNECTIONS ...continued For freestandingg units using natural gas, using a metal flex hose is recommended. This is available at your local hardware store or from your dealer. LP GAS Grills set up for LP gas come equipped with an LP hose/ regulator assembly for connection to a standard 20 lb. LP cylinder. (Type 1). All fittings necessary to attach the assembly to the grill are included. WARNING Do not change the regulator/hose assembly or use any other assembly than the one supplied with your grill.
GAS CONNECTIONS ...continued Insert the regulator inlet into the cylinder valve and turn the black coupler clockwise until the coupler is hand tight. Do not over-tighten this connection. To disconnect the coupler, first make sure the main cylinder valve is turned off. Grasp the coupler and turn counter clockwise. The inlet will then disengage. Always leak-test the connection after refilling or exchanging LP cylinders. (See INDEX: “Leak Test” for further details.
GAS CONNECTIONS ...continued NG AND BULK PROPANE CART INSTALLATION • Shut off the gas supply at the main valve. rill • Disconnect all plumbing (if already attached) from the g grill and the gas supply valve. • Remove all the fittings from the grill manifold. • Install the side burner into the counter top cutout. Grill Manifold with Brass Elbow Angle At Least 20˚ From Horizon e • Connect the gas supply to the grill as shown in the diagrams on this page for your gas type. ns.
ELECTRICAL CONNECTIONS WARNING: ELECTRICAL GROUNDING • Product installation must meet local electric codes or, in the absence of local codes, the latest edition of the National Electrical Code ANSI/NFPA No. 70 or the Canadian Electrical Code CGA 1.6b2005. • Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas appliance. • IMPORTANT: When connecting your rotisserie motor, first connect the motor to the grill and then plug the grill into the outlet.
FINAL CHECKS LEAK TESTING LOW HEAT BURNER ADJUSTMENT FOR MAIN CERAMIC BURNERS AND TRIDENT™ BURNERS ONLY! DANGER! To prevent fire or explosion hazard, DO NOT smoke or allow any potential source of ignition (sparks, electrical arcing, etc) in the area while performing a leak test. Leak tests should be conducted outdoors only. Never conduct a leak test using fire or flame. DO NOT ADJUST THE ROTISSERIE BURNER. The main ceramic burners and Trident™ burners on your grill feature an adjustable low setting.
FINAL CHECKS ...continued BURNER FLAME ADJUSTMENT Each grill burner is tested and adjusted at the factory prior to shipment. However, fluctuations in gas pressure, gas conversion and even in the quality of the gas itself may make it necessary to adjust the burner. Flames should be blue and stable with slight yellow tips. The bright-blue core should be about 3/8 inch high with a total flame height of about 1 1/2 inches.
A MESSAGE TO OUR CUSTOMERS You’ve just joined a discriminating collection of amateur and professional chefs that take outdoor cooking to a new level. Your grill has been designed and built with meticulous attention to detail and it offers some unique and powerful features. You can achieve maximum performance and enjoyment of these features only by carefully reading this manual ... before your first cook-out. This manual includes important safety tips and great hints for better grilling.
GRILLING IN WINDY CONDITIONS Outdoor grills create more heat than interior kitchen ranges. That’s how they sear and grill steaks and other foods. These high-performance burners require a constant, steady supply of fresh air to mix with the fuel. Your grill pulls air in through the front and vents hot gases out through the rear. Wind hitting the back of the grill can disrupt proper exhaust. become extremely hot.
PRE-GRILL CHECKLIST BEFORE YOUR FIRST USE There are a few must-check safety precautions to consider before you use your grill. Please be sure that: • All packing materials and tie-downs have been removed from the burners. (See INDEX: “Unpacking & Assembly” for further details.) • You have fuel connected. (See INDEX: “Gas Requirements” for further details.) • You have electric connected. (See INDEX: “Electric Requirements” for further details.
LIGHTING YOUR GRILL ELECTRIC IGNITION For the Rotisserie Burner: Before proceeding, make sure you have completed the “Before Each Use” checklist. The rotisserie burner features a thermocouple sensor with a safety valve that automatically shuts off the flow of gas if the burner goes out. (See INDEX: “Windy Conditions” for tips on how to prevent burner blow out) Follow these steps to light any of the burners on your grill: First, make sure all burner control knobs are set to OFF.
BASIC GRILLING USING THE TRIDENT™ BURNER PRE-HEATING Pre-heating your grill every time you use it is extremely important. Pre-heating allows the briquettes to properly heat up, providing more even and more consistent cooking results. Pre-heat your grill by igniting all main burners, including the ProSear™ burner, and setting them to “HI”. Then close the hood and allow the grill to heat for 10 to 15 minutes.
USING THE TRIDENT™ BURNER HOW TO SEAR The Motor Searing locks in flavor and juices while allowing the food’s outer surface to absorb smoke and food-born aromas produced when drippings are vaporized by the burner. Install the motor by sliding it into one of the slots shown here. Use the top slot for small foods or fast cooking and the lower slot for large foods and slower cooking. The result is a restaurant-style finish … crisp, flavorful outside with a tender, juicy inside.
USING THE ROTISSERIE BURNER ...continued Swing the warming rack up and out of the way. It will rest in place. The notched portion of the skewer must rest on the rollers for proper operation. Then mount the skewer on the grill before lighting the rotisserie infrared burner. Lighting the burner first could result in burning your hands while trying to mount the skewer on the grill.
CLEANING YOUR GRILL STAINLESS STEEL the product. Our products are known for their attractive appearance. We achieve this by selecting only the finest grades of stainless steel and applying exacting workmanship. Here are a few tips to avoid this: In order to maintain this attractive appearance over the life of the grill it is important to take the following steps: • Allow the surfaces to dry before installing the cover. Do not cover a damp grill.
CLEANING YOUR GRILL ...continued WARNING GRILLING RACKS The easiest way to clean the grill racks is to do so immediately after turning off the burners, while they are still hot. Wearing a long BBQ mitt to protect your hand from steam, dip a brass bristle brush in hot water and scrub the grill rack. Dip the brush frequently because the steam helps remove baked-on foods. PROPER PLACEMENT OF EACH BURNER IS CRITICAL. AFTER CLEANING THEY MUST BE CENTERED ON THE BRASS ORIFICE, RESTING LEVEL WITHOUT ANY ROCKING.
CLEANING YOUR GRILL ...continued Every 3 to 6 months, remove the burner and inspect the venturi (inlet) and orifice to ensure that they’re free of obstructions. Food debris on the inside of the burner can be gently shaken out. Do not touch the ceramic surface.
POTENTIAL PROBLEMS ...continued SMELL OF GAS WHILE COOKING IF YOU SMELL GAS WHILE THE GRILL IS OPERATING, IMMEDIATELY TURN OFF ALL BURNERS AND SHUT OFF THE MAIN FUEL SUPPLY. • Perform a leak test (See INDEX: “Leak Test Procedure” for further details.) • Check for blockages (See INDEX: “Clean the Brass Burner” for further details.) YELLOW FLAMES is set-up for an LP Gas Cylinder. Ensure the LP hose is not behind the grill.
POTENTIAL PROBLEMS ...continued WIND HITTING GRILL ROTISSERIE LIGHTS BUT GOES OUT AS SOON AS CONTROL IS RELEASED Wind hitting the grill while in use, especially winds blowing into or across the hood gap from behind, can cause poor performance and in some cases can cause the control panel to get dangerously hot. • Check Thermocouple The control knob must be held in for 30 to 60 seconds after ignition for the rotisserie burner to stay lit. (See INDEX: “Lighting Rotisserie Burner” for further details.
CONTACTING CUSTOMER SERVICE If service is required, call your authorized service agency. Have the following information readily available. • Model number • Serial number • Sotware Version • Date purchased • Name of dealer from whom purchased Clearly describe the problem that you are having.
LYNX LIMITED WARRANTY I. Limited Lifetime Warranty The stainless steel grill body, ceramic grill burners, cooking grates,Trident TM burner and rotisserie infrared burner are warranted to be free from defects in material and workmanship when subjected to normal domestic use and maintenance for the lifetime of the original purchaser. This warranty excludes surface corrosion, scratches, and discoloration which may occur during normal use.
LYNX COMMON AREA LIMITED WARRANTY The Lynx Limited Warranty covers residential installations only and is non-transferable to any other party. This warranty applies when the product is installed in common areas where more than a single party has rightful access to its use or in locations considered beyond normal residential use such as B&B's, and private clubs. THIS PROVISION EXCLUDES ALL COMMERCIAL APPLICATIONS, INCLUDING, BUT NOT LIMITED TO RESTAURANTS AND INSTITUTIONAL FOOD SERVICE LOCATIONS. I.
WIRING SCHEMATICS 27” / 30” ROTISSERIE GRILL 40 | INSTALLATION / USE & CARE
WIRING SCHEMATICS 36” & 42” ROTISSERIE GRILL INSTALLATION / USE & CARE | 41
WIRING SCHEMATICS 54” ROTISSERIE GRILL 42 | INSTALLATION / USE & CARE
INSTALLATION / USE & CARE | 43
Lynx Grills 62201 Hwy 82 West Greenwood, Mississippi 38930 USA 888-289-5969 www.lynxgrills.
