Sedona Cart Assembly

ManualsBrandsLynx ManualsLiquid Propane Gas GrillsLynx Professional 42" Sedona Liquid Propane Freestanding Grill

Assembly Instructions:

SEDONA L400CART

L500CART

& L600CART

Sedona Freestanding Cart

Model L400CART, L500CART &L600CART

Lynx Grills, Inc., 6023 E. Bandini Blvd. Commerce, CA 90040 Phone: (323)838‐1770 Fax: (323)838‐1778 | www.lynxgrills.com

Document 33807 Rev C 02/08/13

Step 1.

Step 2.

Step 3.

Step 1.

After opening and identifying the components, select the back

panel assembly and either the right or left side panel assembly.

Orient the parts as shown in the illustration for step 1.

Note that these parts are upside down with the shelves at the

floor. Hook the right or left side to the back into the four keyways

located on the edge. When attached all four keyways should be

engaged and the back and side flush to the top.

Repeat this step for the opposite side panel.

Step 2.

With the cart oriented upside down, locate the 4 - #8 screws and

nuts and mount the electrical transformer to the access plate

shown in the illustration for this step. It may be done at the end of

the assembly but is somewhat easier to access at this stage.

Step 3.

Refer to the figure for step 3 and insert the base assembly into the

cavity at the back corners of the cabinet. Check that the tank hole

is positioned as shown and the magnet is located on the open side.

Splay the two sides out slightly and enclose them over the front of

the base. The sides and back have pockets that fit over the casters

for clearance. Use 4 of the ¼-20 x ½ screw at each corner to lock

the assembly in place.

Access

Plate

magnet

tank

hole

Screw

4 places

Introduction:

Your Freestanding Cart comes with all of the components necessary

to assemble a cart for the SEDONA Series of Lynx Grills.

The SEDONA CART series is comprised of 8 sub assemblies:

1. Back Panel Assembly

2. Right Side Panel Assembly with Shelf

3. Left Side Panel Assembly with Shelf

4. Base Assembly with Wheels

5. Inner Shelf Assembly

6. Cross Brace Assembly

7. Right Door

8. Left Door

In addition there are 14 screws (1/4 -20 x ½) to assemble the

cart and grill and 4 screws with nuts (#8-32 x 3/8) to attach the

transformer assembly supplied with the Grill.

Summary of content (3 pages)

PAGE 1
TM Assembly Instructions: SEDONA L400CART L500CART & L600CART Sedona Freestanding Cart Model L400CART, L500CART &L600CART Introduction: Your Freestanding Cart comes with all of the components necessary to assemble a cart for the SEDONA Series of Lynx Grills. The SEDONA CART series is comprised of 8 sub assemblies: 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 2
Step 4. To begin step 4 turn the cabinet upright to secure the Inner Shelf Assembly. The L400 and L500 shelf will only assemble as shown at the right with the electrical hole to the rear and the screws mounting at the back and left side. The shelf is not only useful but necessary for the proper stability of the cart. DO NOT omit the inner shelf or any part in these instructions. The inner shelf is secured by 4 of the ¼-20 x ½ screws. Two through the back and two through the left side.
PAGE 3
Step 6. With assistance, remove all packing materials from the grill. Also remove the grates and warming racks to lighten the assembly. The grill will be placed onto the cart as illustrated in this step. The back edge will engage first and the front will slide down into position until horizontal. Using at least two people – with gloves - grasp the front and side of the Grill at points A and B. Place the unit on the cart and lower it slowly until horizontal.