Vent Hood Owner's Manual

ManualsBrandsLynx ManualsDomestic AppliancesLOH36

Page 1 of 8 P/N 11857.00 Rev A

INSTALLATION INSTRUCTIONS

HOOD MODELS – LOH36, LOH48 & LOH60

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING.

INSTALLATIONS MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector's use.

INSTALLER: Please leave these Installation Instructions with this unit for owner.

OWNER: Please retain these Instructions for future reference

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, HOODS

SHOULD BE INSTALLED WITH VENTILATORS APPROVED FOR USE WITH THE HOOD. SEE TABLE – 1 ON

THIS PAGE FOR APPROVED VENTILATORS.

WARNING - TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

A. Installation work and Electrical Wiring

Must Be Done By Qualified Person(s) In

Accordance With All Applicable Codes

& Standards. Including Fire-Rated

Construction. “WARNING” To Reduce

The Risk Of Fire, Use Only Metal Duct

Work.

B. Sufficient air is needed for proper

combustion and exhausting of gases

through the flue (chimney) of fuel

burning equipment to prevent

backdrafting. Follow the heating

equipment manufactures guideline and

safety standard such as those published

by the National Fire Protection

Association (NFPA) and the American

Society for Heating, Refrigeration and

Air Conditioning Engineers (ASHRAE),

and the local code authorities.

C. When cutting or drilling into wall or

ceiling, do not damage electrical wiring

and other hidden utilities.

D. Ducted fans must always be vented to the

outdoors.

E. Before Servicing or Cleaning Unit,

Switch Power off At Service Panel And

Lock Service Disconnecting Means to

Prevent Power From Being Switched On

Accidentally. When The Service

Disconnecting Means Cannot be Locked,

securely Fasten A Prominent Warning

Device, Such As A Tag, To The Service

Panel

CAUTION - TO REDUCE THE RISK OF FIRE AND TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR

OUTSIDE FOR DUCTED FANS – DO NOT VENT EXHAUST AIR INTO SPACE WITHIN WALLS OR CEILING

OR INTO ATTICS, CRAWL SPACES OR GARAGES.

Read this instruction completely before starting installation. Planning the complete installation before starting any work is

highly recommended. This includes all aspects of the installation including hood location, ducting, electrical requirements, and

adequacy of mounting surfaces.

TABLE - 1

Model LOHI = Internal ventilator

Model LOHE = Remote ventilator

This hood series has been designed to be used with the ventilators shown in Table – 1. Before

cutting into cabinets, it is necessary to confirm that the correct ventilator is being used. Your

dealer should have reviewed your needs prior to your purchase. Be sure you have the correct

ventilation system.

CAUTION: To Reduce The Risk Of Fire And Electrical Shock, Install This

Rangehood Only With Blowers Manufactured By Lynx Professional Grills.

DUCTING: Use a minimum 10" round duct for LOHI and LOHE installations. See Page – 3. A standard starting transition

(33895) is included with the Hood.

SAFTY WARNING:

Turn off power circuit at the service entrance and lockout panel before wiring the range hood.

NOTE: Unit must be vented

to the outside of the building.

Summary of content (15 pages)

PAGE 1
INSTALLATION INSTRUCTIONS HOOD MODELS – LOH36, LOH48 & LOH60 IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING. INSTALLATIONS MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspector's use. INSTALLER: Please leave these Installation Instructions with this unit for owner.
PAGE 2
BEFORE STARTING INSTALLATION, YOU MUST IDENTIFY THE VENTILATOR MODEL BEING USED AND IF A TOP OR REAR EXHAUST IS TO BE USED. Prepare cabinet and/or wall for mounting either top (Fig - 1) or rear (Fig 6 & 7) exhaust. Use furring strips to level cabinet mounting surface with any cabinet trims.
PAGE 3
Hood Width HOOD MODELS LOHI TOP EXHAUST FIG-1 36" 48" 60" Bottom View Of Cabinet Internal Or Remote Blowers 5" C L "A" 7-1/8" 4" 12" 10-1/4" 3/4" Back Wall Add Furring Strips To Provide An Even Bottom Surface For The Hood Mounting Vertical Discharge Secure Transition To Hood Using #6 X 3/8" Sheet Metal Screws.
PAGE 4
Outside Patio or Lanai Installation Construction methods and installation shall comply with all local building codes. Internal ducting shall be sealed using outdoor rated metal duct tape. The LYNX hood with stainless steel canopy is approved for installation in an outside patio or lanai area if the area is covered with a protective roof over the hood (wall style hoods are to be also mounted to a solid protective rear wall) and installed with a GFCI protected branch circuit.
PAGE 5
The installation instruction that accompanies the hood shall be followed to ensure all safety Instructions and guidelines are adhered to. NOTE: Hood is recommended for use over domestic gas or electric appliances. Not recommended for use over solid fuel fired appliances. See Fig-10 for soffit construction 12" Roof Cap Soffit A B Top Exhaust A A = 42" Minimum Front View Fig - 9 B = 30" Minimum Side View See Fig – 10 for structure with elevated roof/ceiling.
PAGE 6
NOTE: 4-1/4” Tall Starting Transition is Included with the Hood. Transition dimensions may very. Before assembling transitions to hood, fit them into the prepared cabinet opening to be sure the openings are large enough to accommodate the transition. Enlarge the hole if required 4-1/4" 14 - 1/ Attach the transition (See DUCTING, pg 1), supplied with hood as described previously in this instruction.
PAGE 7
Page 7 of 8 P/N 11857.
PAGE 8
Lynx Professional Grills 6023 E. Bandini Blvd. Commerce, CA 90040 Service: (888) Buy-Lynx (888-289-5969) Fax: (323) 838-1778 www.lynxgrills.com Page 8 of 8 P/N 11857.
PAGE 9
Installation Instructions Model: LOHE Ventilator for External Installation IMPORTANT SAFETY INSTRUCTIONS: READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. Installation must comply with all applicable codes. READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Save for local electrical inspector's use. INSTALLER: Please leave these instructions with this unit for the owner. OWNER: Please retain these instructions for future use.
PAGE 10
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Provide square hole through the roof or wall as shown by dash lines for conduit as shown in Fig-2. For reference, location of 10" duct connection and wiring connection is shown with solid lines. Remove shipping bracket per separate instruction. SEE PAGE - 2 Install ventilator on roof or wall, with discharge (screened end) pointing down, according to STANDARD ROOFING PROCEDURES.
PAGE 11
FIG - 1 TYPICAL INSTALLATION Outside Wall Mount Roof Mount Air Discharge Roof 10" Elbow 10" Duct 10" Transition 10" Elbow 10" Transition Air Discharge Hood Outside Wall Hood FIG - 2 FIG - 3 14" Top View Down Slope of Roof or Wall 1-1/2" 6" 2" 18" 10-1/2" 30" 24" 4-1/2" 7-3/4" 1-1/2" FIG - 5 FIG - 4 24" 3" 8" Air Discharge Conduit 10" Adjustible Elbow Screw and Tape Joint 10" Diameter Duct 5-5/8" 4" 10-1/4" 30" 10" Duct Connector 2" 8" 1-5/8" 7-1/8" 2-3/4" 7-1/2" Page 3 of 4 P
PAGE 12
FIG - 6 Hood Receptacle Box Power Supply N G L1 Receptacle Plug 1. Remove Shaded Twist Ons 18 B #12 18 G #11 2.
PAGE 13
LOHI INSTALLATION INSTRUCTION CAUTION: Before installing ventilator read the HOOD INSTALLATION INSTRUCTIONS. PARTS INCLUDED: 1 - Ventilator Assembly 4 - #8 x ½ Pan Head SMS 1 – Wire Harness (#33896) 1 – Wire Tie A 1) Install Hood & Transition per hood installation instruction. 2) Remove parts from carton. Remove all corrugated packaging shims between motor and housing. 3) Rotate ventilator wheels to confirm they rotate freely. 4) Connect Wire Harness #33896 to Hood Receptacle Box.
PAGE 14
INSTALLATION INSTRUCTIONS GRAVITY DAMPER AND COLLAR WITH BIRD SCREEN PART # LOHC INSTALLER: Please leave these Installation Instructions with unit for the owner. Do not force shutter into opening!, Do not open shutter by lifting individual blades!. Do not install shutter leaning forward or backward! 1. Shutter frame should be mounted level and squarely on outside wall. Care should be taken not to twist the shutter frame. Never cover shutter with siding or masonry work.
PAGE 15
HOOD EXTENSION KITS INSTALLATION INSTRUCTIONS LHE636, LHE1236 / LHE648, LHE1248 / LHE660, LHE1260 s CAUTION: Read this instruction and your hood installation instruction before starting installation. Plan the complete installation before starting any work. This includes all aspects of the installation including hood location, ducting, electrical requirements and adequacy of mounting surfaces.