LUNA 1000-1150-1300-1600 DH GOLD GAS LUNA 1000-1300-1600 CL / CR GOLD GAS (Corner Left /Corner Right) LUNA 1000-1300-1600 DC GOLD GAS ( Double Corner ) INSTRUCTION FOR INSTALLATION AND USE English 11-2012 1
V E RY I M P O R TA N T I N S T A L L A T I O N INSTRUCTIONS FOR THE M - D E S I G N GAS FIREPLACES T H E S U P P L I E R TA K E S N O RESPONSBILITY FOR ANY POSSIBLE DAMAGE, POOR WORKING APPLIANCES AND ACCIDENT AS A R E S U LT O F I N C O R R E C T I N S TA L L AT I O N MAINTENANCE GAS FIREPLACE M-DESIGN THE M-DESIGN GAS FIREPLACES MUST BE CHECKED every 2 years and GET a MAINTENANCE. THIS IS ALSO TO MAINTAIN YOUR WARRANTY. IF THIS WILL BE NOT OBSERVED, THE WARRANTY FELL.
SUMMARY 1. GENERAL REMARKS............................................................... 5 2. CONNECTION........................................................................... 5 3. INSTALLING THE FIREPLACE.............................................. 3.1.1 Positioning the fireplace................................................... 3.1.2 Gas connection................................................................... 3.1.3 Electrical connection . .........................
OPEN AND CLOSE THE DOOR CLOSING OPEN KEY IF SOME DUST OR WASTE IS SEEN ON THE WINDOW ( INSIDE AND OUTSIDE ), CLEAN THIS BEFORE THE FIRST USE OF THE FIREPLACE.
1. GENERAL REMARKS This is a moulding of the closed combustion system, designed for the atmosphere and comfort of your living-room. It constitutes an efficient source of heat and gives the impression of a real chimney fire. The gas with air-vent furnaces are based on the principle of natural extraction from the furnace, which eliminates flue gas outside and brings in air (oxygen) from outside the house which is necessary for combustion of the gas. It uses to this effect two concentric pipes.
3. INSTALLING THE FIREPLACE After having checked the appliance, you ready to install your appliance. This is done as follows 3.1.1 POSITIONING THE FIREPLACE Place the fireplace on a stable surface using the adjustable feet. Adjust the height of the fireplace by turning the bolt ( pic 1 ) The stove may not be placed direct ont the floor to allow natural convection. The appertures for the air supply ( IN ) is situated underneath the appliances.
3.1.2 GAS CONNECTION The appliances are standard delivered with a 1/2” gas solded connection ( fig. 1 ). It is always located at the left-hand side of the appliance. Make sure nothing remains in the gas lines, since this may easely lead to blockage. An approved gas valve should always be connected to the appliance, wich must be accesible at all time . For this you can use a acces door ( pic. 1 next page ).
PIC. 1 ROOF EXIT ( C31 ) TAB. 1 This is recommanded with a roof exit > 3m Ø 150/100 C (min) 3m C (max) 17m 1150 DH 3m 17m Restriction HR+ (as from 4m) Ø 60 as from 2 m : Ø 75 Ø 60 1300 DH / CL/CR / DC 3m 17m Ø 60 1600 DH / DC 3m 19m Ø 75 Appliance 1000 DH / CL /CR / DC DH = Double Face CL = Corner Left CR=Corner Right DC = Double Corner TAB.
PIC. 2 ROOF EXIT VIA EXISTING CHIMNEY (C91) TAB. 1 150 (min) / Ø 100 C (min) C (max) Restriction HR+ (as from 4m) 1000 DH / CL / CR / DC 1150 DH 3m 3m 17m 17m Ø 60 Ø 60 1300 DH / CL / CR / DC 3m 17m Ø 60 1600 DH / CL / CR / DC 3m 19m Ø 75 Appliance DH = Double Face CL = Corner Left CR=Corner Right DC = Double Corner TAB.
PIC. 3 WALL EXIT (C11) Ø 150/100 WITH REDUCTION USVK13 ON THE APPLIANCE (FIG. 3 ) Appliance A (min) B (min) B (max) Restriction HR+ 1000 DH/CL/CR/DC 1,25*m wall exit =A+0,5m Ø 75 1150 DH 1,25*m wall exit =A Ø 75 1,25*m wall exit =A 1300 DH/CL/CR/DC DH = Double Face CL = Corner Left CR=Corner Right DC = Double Corner Ø 75 PIC. 4 WALL EXIT (C11) (A) Ø 200/130 in combination with (B) Ø 150/100 WITH REDUCTION USVK13 AFTER 90° CURVE ON HORIZONTAL PART ( FIG.
Ø 200/130 Appliance A (min) B (min) Restriction HR+ B (max) 1000 DH/CL/CR/DC 1m wall exit Ø 70 A+7m 1150 H 1m wall exit Ø 75 A+6m 1300 DH/CL/CR/DC 1m wall exit Ø 75 A+5m 1600 DH/CL/CR/DC 1m wall exit Ø 90 A+3m DH = Double Face CL = Corner Left CR=Corner Right DC = Double Corner A B 3° Pic.5 Pic.6 IMPORTANT : BE CAREFULL EVERY HORIZONTAL PART DOES NOT HAVE AN NEGATIVE INCLINATION (pic.5) IN DIRECTION OF OUTLET.
Pic. 5 ROOF EXIT with 90° bends Ø 150/100 WITH REDUCTION USVK13 oN APPLIANCE Aplliance 1000 DH / CL / CR / DC 1150 DH A (min) 1,25 m 1,25 m B (max) A+C A+C C (min) B-A-1m B-A-1 (A+B+C )max 17m 16m 1300 DH / CL / CR / DC 1,25 m A+C B-A-0,5 15m 1600 DH / CL / CR / DC 1,25 m A+C-1m B-A 14m DH = Double Face CL = Corner Left CR=Corner Right DC = Double Corner Fig.
5. INSULATION AND FINISHING Please , follow this instruction. The appliance can overheat if you not apply those instructions. Errorcode F02 will appear ! Once installation is complete, the appliance can be fitted. Before doing so, check the tightness of the gas pipe one more time. Light the appliance and check that it is working: check the tightness of the gas pipe and the smoke pipe. Once you have checked everything, you can perform the final insulating and finishing operations.
6. CONVECTION CURRENT Please , follow this instruction. The appliance can overheat if you not apply those instructions. Errorcode F02 will appear ! The enclosure of the furnace must be provided with ventilation grills or openings allowing for the elimination of heat by convection. It is possible to have a convection kit fitted with the furnace. This system directs the heat inside the room by means of flexible tubes ( dia. 150 mm).
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 15 2 dm² Inlet Grid convection air Design Grid ( outlet ) with 2 connections INLET CONVECTION OUTLET CONVECTION OR Pic.
YOU HAVE TO CONNECT AT LEAST TWO APPERTURES SITUATED AT THE TOP OF THE APPLIANCE. FOR THE LUNA 1600, YOU MUST CONNECT 4 APPERTURES. THE STOVE MAY NOT BE PLACED DIRECT ON THE STOVE MAY NOT BE PLACED DIRECT ON THE FLOOR, WTHOUT THE FEETS. THIS TO ALLOW NATURAL CONVECTION. THE APPERTURES FOR THE AIR SUPPLY ARE SITUATED UNDERNEATH THE APLLIANCE. EVERY OPENING YOU MAKE MUST BE CONNECTED WITH A FLEXIBLE TUBE dia.150MM (see pic. below). THIS WILL AVOID THE HEATING OF THE ELECTRONIC PART OF THEAPPLIANCE.
7. MOUNTING A 3-SIDED FRAME 3-sided frame pic 1 upper frame sideframe 2,25cm 4 sided frame (lower piece) pic 2 Fireplace is delivered standard with 4sided frame 3,5cm, an upper and 2 sideframes ( see pic. 2 ) Before mounting the 3 sided frame, remove 4 sided frame ( lower piece ) by lift it carefully up. Pull out the upper frame and in second way the left and right sideframes. Take the left and right side of the 3 sided frame ( 3,5 - 7 or 10 cm ) and slide them in the notches ( see pic 4 ).
8. PUTTING IN PLACE THE LOGS, DIAMOND, SAPPHIRE AND WHITE STONES • Please check that the pilot light is switched off and that the furnace has cooled down. • Move the window to the front by pulling it. The window tips open at 45°. • Arrange the materials supplied. In accordance with your order you will have either a set of logs, diamond, sapphire or white pebbles. There is an adequate supply of materials . Our appliance is approved with these materials, so please do not use other products.
9 6 4 7 5 3 4 3 7 2 1 LUNA 1000 DH/CL/CL/DC GAS 9 8 1 8 2 5 6 LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 19
LUNA 1000 DH/CL/CR/DC GAS LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 20
9 7 6 4 3 5 8 5 2 3 4 7 2 1 9 8 6 1 LUNA 1150 DH GAS LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 21
LUNA 1150 DH GAS 7 6 LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 22
7 10 6 9 12 5 8 7 12 2 9 6 3 4 10 5 8 1 4 2 3 1 11 11 LUNA 1300 DH/CL/CR/DC GAS LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 23
LUNA 1300 DH/CL/CR/DC GAS LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 24
13 7 6 3 9 8 10 9 11 12 5 12 13 2 11 8 4 10 7 3 2 1 4 LUNA 1600 DH/CL/CR/DC GAS 5 1 6 LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 25
LUNA 1600 DH/CL/CR/DC GAS LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 26
9. FIRST-TIME USE The masonry and plaster surrounding a recently installed furnace hold a great deal of moisture, which must first evaporate before commissioning the appliance. If not, the plaster may crack or split. Ask your installer about the timescale to follow. The first time you use it, only make a moderate-sized fire. The first few times the furnace is used, an unpleasant odour may be apparent. It comes from the protective paintwork. These emissions are totally harmless.
11. STARTPILOT The M-Design Gas appliance are provided with “Constant startpilot”. After the first use or when the winterperiod is coming and you use the fireplace daily, you must let the startpilot switch ON. Don’t switch it off after each use. This startpilot avoids condensation in the fireplace and protects the whole appliance and even the electronic parts against humidity. This startpilot has a very low gasconsumption. 12.
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 29 G20 86,4 7 6,1 5 1 Nominal Charge (KW) Charge (KW) NOX-emmission classe Cat. Rendement CE / 1 7,5 6,4 5 86,8 6 x 0,95 38/33A 6 x 0,95 38/33A Rendement (%) 0,789 0,870 C91 I2E Consumption (m3/h) Injector burner Injector startpilot C11 , C31 , I2E+ 20 19,3 C91 I2L 25 24,2 C11 , C31 , G25 I2H NATURAL GAZ 2 6,5 4,7 5 73 6 x 0,6 0.
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 30 G20 83 7 6,1 5 1 Nominal Charge (KW) Charge (KW) NOX-emmission classe Cat. Rendement CE / 1 7,5 6,4 5 86,2 6x1 38/33A 6x1 38/33A Rendement (%) 0,789 0,870 C91 I2E Consumption (m3/h) Injector burner Injector startpilot C11 , C31 , I2E+ 20 19,3 C91 I2L 25 24,2 C11 , C31 , G25 I2H NATURAL GAZ 0,264 30 29,4 2 6,5 4,7 5 73 6 x 0,6 0.
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 31 G20 9,2 8,0 5 1 Nominal Charge (KW) Charge (KW) NOX-emmission classe Cat. Rendement CE / 1 9,7 8,4 5 87 6 x 1,10 38/33A 6 x 1,10 38/33A 85 1,026 C91 I2E 1,132 C11 , C31 , I2E+ 20 19,2 C91 I2L 25 24 C11 , C31 , G25 I2H NATURAL GAZ 2 8,4 5,9 5 70 6 x 0,65 0.
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 32 G20 11,2 9,5 5 1 Nominal Charge (KW) Charge (KW) NOX-emmission classe Cat. Rendement CE / 1 11,9 10,1 5 85,2 6 x 1,25 38/33A 6 x 1,25 38/33A 85 1,262 C91 I2E 1,393 C11 , C31 , I2E+ 20 18,8 C91 I2L 25 23 C11 , C31 , G25 I2H NATURAL GAZ 2 10,3 7 5 68 6 x 0,75 0.
LUNA 1000 DH GOLD gas/gaz * Connection Gas * LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 33
LUNA 1000 CL/CR GOLD gas CL : Corner Left CR : Corner Right * Connection gas on the left for the CR Connection gas on the right for the CL LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 34
LUNA 1000 DC GOLD gas Connection Gas LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 35
LUNA 1150 H GOLD gas * Connection Gas * LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 36
LUNA 1300 DH GOLD gas * Connection Gas * LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 37
LUNA 1300 CL/CR GOLD gas CL : Corner Left CR : Corner Right * Connection gas on the left for the CR Connection gas on the right for the CL * * CR LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 38
LUNA 1300 DC GOLD gas Connection gas LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 39
LUNA 1600 DH GOLD gas * Connection gas * LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 40
LUNA 1600 CL/CR GOLD gas CL : Corner Left CR : Corner Right * Connection gas on the left for the CR Connection gas on the right for the CL * CR LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 41
LUNA 1600 DC GOLD gas Gas Connection LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 42
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 43
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 44 B(mm) 955 1255 1555 B(mm) 367 367 367 C(mm) 371 371 371 D(mm) 55 55 55 E(mm) 35 35 35 B(mm) 402 402 402 C(mm) 406 406 406 D(mm) 90 90 90 E(mm) 70 70 70 1000 DC 1300 DC 1600 DC A(mm) 1148 1448 1748 B(mm) 437 437 437 C(mm) 441 441 441 D(mm) 125 125 125 E(mm) 105 105 105 4-zijdige kader 10,5cm/ Cadre 4-coté 10,5cm/4-sided frame 10,5cm/4-seite Rahme 10,5cm 1000 DC 1300 DC 1600 DC A(mm) 1078 1378 1678 4-zijdige kad
14. GUARANTEE This page is your warranty card. The guarantee is only valid for faults caused by construction defects or defects in the parts used to build the furnace. M-Design offers a 12 month guarantee on all electronic parts and a 8 year guarantee on the furnace construction. Caution: The following items are always excluded from the guarantee: The glass, door, joints and internal decor.
15.
LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 47
16.
SPARE PARTS CORNER GAS LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 49
SPARE PARTS DOUBLE CORNER LUNA 1000DH/CL/CR/DC - 1150DH - 1300DH/CL/CR/DC - 1600DH/CL/CR/DC GOLD - GAS 50
