User manual

GB
ENGLISH | easy2wire ADB
1111
Connecting the radio extension module VTX-BELL
The VTX-BELL can be used to transfer the bell signal by radio to the
recipient of the BELL series (currently BELL 200 RX, BELL 210 USB and
BELL 220 RX). The radio module is attached to the 3-pole plug (B.15)
inside the indoor station. You need the short 3-pole extension that is
included in the VTX-BELL.
IMPORTANT: Please only connect the mains power supply to the
power once the system has been fully mounted. Otherwise short-
circuiting can occur during installation, which can destroy the apparatus
in the worst case.
NOTE: The outdoor station is splash proof in accordance with IP 44. In
heavy rain, particularly in conjunction with high winds, it is still possible
for water to penetrate the casing. We therefore recommend only
mounting the station in a protected outdoor area. If it is not possible to
mount the station in a protected indoor area then weather protection
should be fitted over the outdoor station.
Assembly
The outdoor station should be mounted on a level wall and it must not
distort when screws are inserted. This is equally valid for the indoor
station(s).
1. Remove both the screws (A.8) that attach the front cover out of the
outdoor station.
2. Lift off the stainless steel front cover. In order to do this, hold the
sides with your fingers and push the nameplate out backwards
using both thumbs. The large illuminated field may stick and may
need to be pushed backwards a little.
3. Now the casing screws (A.5) and the screws (A.7) for the terminal
cover (A.6) have been revealed. First remove the screws from the
terminal cover and lay the terminal cover to one side.
4. Remove the six screws from the casing (A.5) and lay them to one
side.
5. Now carefully separate the back half of the casing from the front
half. The two 6-pole plugs that connect the main board with the
terminal can now be removed.
6. Lay the front half of the casing to one side and take the back half
of the casing to draw the mounting holes at the location for the
outdoor station.
7. Drill the mounting holes with a suitable 6 mm drill and insert one
of the included dowels into each hole.
8. Feed the connection wire through the feed-through and screw the
back half of the casing onto the wall.
9. Connect the wire that you have laid onto the terminal.
10. Adjust the nameplate as desired (see ‘adjusting the name plate
and illuminated field’).
11. Then carry out steps 1 to 5 in reverse order in order to re-assemble
the outdoor station.
Note: If the illuminated field and the name plates do not stay in
position of their own accord when the stainless steel front cover
needs to be replaced then you can secure the illuminated field and
the name plates with a strip of sticky tape.
Adjusting the name plate and illuminated field
The nameplate consists of two transparent plastic sections that are
joined with 2 screws.
12. Remove both screws and take the nameplate apart. The foil for the
lettering is between the two plastic parts.
13. Write on the foil with a smudge-proof felt pen or print a nameplate
with the dimensions 71 x 15 mm using a PC and printer (you can
use normal paper but printable foil from stationery shop is better
suited).
14. Lay the printed nameplate (foil) between the two plastic parts and
screw them back together.
15. Make sure that the back half of the plastic case is assembled
correctly with the front half of the plastic case.
The illuminated field is also made up of two plastic parts, one
of which is firmly attached to the outdoor station and the other
is attached loosely and held in position by the front cover. The
dimensions for the name field are 72 x 62 mm.
ASSEMBLY OF THE INDOOR STATION
The assembly height of the indoor station can be freely selected in
accordance with your situation.
1. The casing on the indoor station is only clipped together and is held
together with projections and notches. The back part can be pulled
away easily to separate the back casing from the front section.
2. Use the back half of the casing to help mark the drill holes. Ensure
that the back half is in a straight line.
NOTE: The back half of the casing can also be attached to a hollow-
wall box. There are corresponding mounting holes for this purpose
around the installation hole for the wire. If this does not provide
enough hold then drill more mounting holes and screw the indoor
station on using these additional holes.
easy2wire AD_AP_I-Manual_210x240_Fin1.indd 11 28.10.14 17:02