IMPORTANT SAFETY INSTRUCTIONS ! WARNING For your own safety and that of your equipment, make sure to take the following precautions. Failure to follow warning notices and instruction may result in property damage, serious injury or death.
WARNING: Use only approved spa tub accessories. Use of improper or non-approved accessory will void the manufacturer’s warranty. WARNING: RISK OF ELECTRIC SHOCK - Install at least 1.5m (5 feet) from all metal surfaces. WARNING: RISK OF ELECTRIC SHOCK - Never operate any electrical appliances when the spa tub is in use or when your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within 1.5m(5 feet) of spa tub.
INSTRUCTIONS NOTE: Ensure to check all parts are present. A: Aluminium foil top lid and zipper 1pc B: Control panel 1set C: Spa pool 1pc D: Temp barrier mat (optional) 1pc E: Digital lock 1pc F: Inflation Hose 1pc G: Filter cartridge 2pcs H: Drainage hose 1pc I: Repair kit 1set J: Manometer 1pc K: Inflatable bladder (optional) 1pc A. Site Requirements WARNING: The floor has to be capable of supporting the expected load of the spa tub.
B. RCD Test WARNING: RISK OF ELECTRIC SHOCK. The RCD plug must be tested before each use. WARNING: Insert the RCD plug into a residual current device (RCD) protected power receptacle only. WARNING: Before inserting the plug into a power receptacle, make sure the current rate of the power receptacle and the fixed wiring are suitable for the Spa. Contact a qualified electrician if you cannot verify. 1. Insert the plug into the power receptacle. (1) 2. Press the “RESET” button.
c) Connect the pin plugs. Make sure that plugs are properly matched together, screw a cap, and then you’ ll see yellow light on control panel, no bent or wet for the pin inside male connector which will cause failure connection. d) Open the air valve under the control panel. Screw one end of inflation hose onto it. e) Unscrew the top part of air valve on the Spa. Screw the other end of inflation hose onto Manometer, and then put into the air valve. f) As previously outlined, test spa’s RCD plug.
j) Fill the Spa Using a garden hose to fill the Spa until it reaches the area between two water lines printed inside the Spa wall. WARNING: 1. Fill in water carefully especially for the first time of use. Water level must reach the minimum water line but not exceed the maximum water line, otherwise it may cause pump failure. 2. Please avoid water spillage which will cause damage to the electric parts. 3. After filling in water, please check air pressure again and make sure the pin reads in green sector.
POWER PACK OPERATION Warning: to avoid function failure and damage, please do not operate until spa is filled with water to the minimum water mark. It is the owner’s responsibility to make sure the installation conditions are met and the following safety and warning rules are exercised. Any failure and damage which result from dry-run, water spillage, excessive humidity, or structural loading will void the warranty.
Function Failure Alarm on the Control Panel When power pack doesn’t work properly, there will be corresponding error code displayed on the control panel in time: Please check details from troubleshooting page. Maintaining Spa Water Poor water quality can be extremely hazardous to your health. We recommend you do following things: A: Please use filter cartridge. Screw the filter onto the water inlet on the spa wall by turning it clockwise.
Special Notice on Water Treatment Please read about water quality and filter in user manual. Always shower before you enter your MSpa! Please use test strip to test your water chemistry before each use of the spa, no less than once per week. The pH level must be between 7.2 and 7.8, total alkalinity between 80 and 120ppm and free chlorine between 3 to 5ppm. Too low of a pH level will result in excessive wrinkles and damage to the spa pool as well as corrosion in the motor unit.
2. Consumers should keep the screws and other small parts during dismantling the filter pump. Any damage or missing parts caused by improper operation will void your warranty. Make sure all water is drained from the spa tub and the control box. This is essential to extend the life of the spa. You could also use a vacuum or hair blower to suck up or blow out the water from the pipe and pump lines. Filter cartridge also needs to be removed. It is recommended to store the spa tub in the original packaging box.
MSpa® products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. Oriental Recreational Products (Shanghai) Co., Ltd. (ORPC) is pleased to extend this limited warranty coverage to the original purchaser of an MSpa® Product. This warranty is not transferable. The warranty period commences on the original purchase date through 6-12 months accordingly.
Damages caused by or attributable to the following incidents are specially excluded: a. Any damage caused by the operation of the spa with water temperatures outside the range of 0°C-42° C/32°F-107.6°F (Europe/Australia) or 0°C-40°C/32°F-104°F (USA) b. Any damage caused by clogged, dirty or calcified filters c. Any damage that are purely aesthetic and do not hinder the function of the MSpa d.
