User manual

26
Filling with salt
Only use salt specifically designed for use in
dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.
Only fill with salt just before starting one of the complete
washing programmes.
This will prevent any grains of salt or salty water, which
may have been spilt, remaining on the bottom of the
machine for any period of time, which may cause
corrosion.
To fill:
1. Open the door, remove the lower basket and unscrew the
cap of the salt container by turning it anticlockwise.
2. Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3. Using the funnel provided,
pour in the salt until the
container is full.
4. Replace the cap making
sure that there is no trace
of salt on the screw thread
or on the gasket.
5. Screw on the cap tightly
turning it clockwise until it
stops with a click.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel
which comes on when the salt has finished.
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been
replenished, assuming the dishwasher remains switched
on. If you are using salts that take longer to dissolve then
this can take longer. The function of the machine is not
affected.
Do not worry if water over flows from the unit when filling with
salt, this is quite normal.
Rinse aid
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying. The
dispenser, which is positioned inside the door, holds about 110
ml of rinse aid, which is sufficient for 16 - 40 dishwashing
programmes, depending upon the dosage setting.
Filling with rinse aid
1. Open the container by pressing the release button (A).
2. Add the rinse aid until the container is completely full. The
maximum level for filling is indicated by "max".
Ensure that the lid is closed after every refill.
Adjusting the dose
According to the finish and drying results obtained, adjust the
dose of rinse aid by means of the 6 position selector (position
1 minimum dosage, position 6 maximum dosage).
Increase the dose if there are
drops of water or lime spots
on the dishes after washing.
The dose is factory set in
position 4.
Reduce it if there are sticky
whitish streaks on the dishes.
Clean up any rinse aid spilt during filling with an
absorbent cloth to avoid excess foaming during the next
wash.
Only use branded rinse aid for dishwashers. Never fill the
rinse aid dispenser with any other substances (e.g.
dishwasher cleaning agent, liquid detergent). This would
damage the appliance.
Top up with rinse aid when the rinse aid indicator light on the
control panel illuminates.
Deactivation/activation of the inflow of
rinse aid
(The dishwasher must be switched off)
When the inflow of rinse aid has been deactivated, also
the rinse aid indicator light on the control panel is
automatically deactivated.
1. Press the On/Off push button. The indicator lights of the
programme selection push buttons will illuminate and in the
digital display are visible 2 horizontal lines (--) (setting
mode).
2. Press simultaneously function push buttons 2 and 3, the
indicator lights of the function push buttons 1, 2 and 3 start
flashing.
3. Press the function push button 2, the indicator lights of
function push buttons 1 and 3 turn off while the indicator
light of the push button 2 goes on flashing, the digital
display indicates the current setting.
4. To change the setting, press again the function push button
2, the digital display indicates the new setting.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off push button or wait about 60 seconds
after which the dishwasher will automatically return to
setting mode.
SALE
ZOUT
SALT
SALZ
SEL
SR14
BR07
BR14
BR09
Inflow of rinse aid deactivated
Inflow of rinse aid activated (factory setting)