M2TECH PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER USER MANUAL REV.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz Warning! Changes or modifications not authorized by the manufacturer can invalidate the compliance to CE regulations and cause the unit to be no more suitable to use.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz Dear customer, thank you for purchasing PALMER POWER STATION. What you have is not just a simple power supply, but a first-rate dedicated power supply with many unique features conceived to obtain the best audio performance out of the YOUNG 384/32 DAC and other 15V-operated M2Tech products.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz INDEX 1. Unpacking........................................................................................................................5 2. Front Panel ......................................................................................................................6 3. Back Panel...............................................................................................................
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz 1. Unpacking The PALMER POWER STATION box contains the following items: • • • Palmer Power Station 1 supply cable terminated with 5.5/2.1mm plug on one end and with Bulgin heavy duty plug on the other end 1 power cord Should any item be missing, please contact your dealer for a warranty claim. Please note the supply cable may be obtained as a separate item if needed.
M2Tech PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER www.m2tech.biz REVISION PrB – DECEMBER 2011 2. Front Panel 1 3 4 2 1) Mains switch. Push to apply mains power to the PALMER POWER STATION. Depending on the status of the output switch (item 2) and the battery charge level, switching power on may start battery charge. Also, charge may be terminated at any time by switching power off. Please see Section 5 for the effect of this switch status over battery charge start policy.
M2Tech PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER www.m2tech.biz REVISION PrB – DECEMBER 2011 3. Back Panel OUT 1 M2TECH OUT 2 PALMER POWER STATION BATTERY LOW-NOISE POWER SUPPLY RATING: 100-240VAC - 50/60HZ POWER CONSUMPTION: 60VA FUSE: 2 x 2.5A Slow BLOW MADE IN ITALY WA RNING! NO USER SERVICEABLE PARTS INSIDE REFER ALL SERVICING TO QUALIFIED PERSONNEL 5 ! S/N: 5 6 7 5) Outputs. Connect the supply cable provided in the package.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz 4. Connections Connect the female plug of power cord to the mains socket (Page 7, no.7) of PALMER POWER STATION. Connect the Bulgin plug of the supply cable to one of the PALMER POWER STATION output connectors (Page 7, no.5). Connect the 5.5/2.1mm plug of the supply cable to the supply input of a 15V-operated M2Tech device.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz 5. Operation 5.1. Charge policy Charge is activated whenever one of the following events occur: a) the unit is powered, the battery is in use and the battery voltage falls below the low battery limit; b) the unit is off (mains switch released, Page 6 no.1), the output switch is on and the unit is powered by pushing the mains switch.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz Battery life can be increased by avoiding complete discharges: user should force a charge cycle after a listening session even if the battery is not completely depleted. This is obtained by powering the unit while the output switch is engaged.
PALMER POWER STATION LOW NOISE BATTERY POWER SUPPLY/CHARGER REVISION PrB – DECEMBER 2011 M2Tech www.m2tech.biz 6. Technical Specifications Supply voltage: ................................. 100-240VAC, 50-60Hz Power consumption: ......................... 2.5A peak, 60VA rated Fuse:................................................. 2 x T2.5A Output voltage: ................................. 15VDC (battery) Output current: 1A (peak, both outputs) Output noise: ....................................