Specifications

MIG Welders and MIG Welding Accessories
14
From the Inside... to the Outside...
HTP Welders are built tough to last long!
Thermoswitch
Protection
–
In the unlikely event
that you exceed the
duty cycle of your HTP
welder, don’t worry,
the thermoswitch will
shut the machine
down, protecting the
internal components
from overheating.
Circuit Breaker
Protection
–
HTP uses circuit
breakers on the
primary input side of
the welder, which
helps to protect the
internal components
from damage.
As we all know, copper
conducts electricity
better than aluminum
and lasts a lot longer.
Copper, most
importantly however,
provides a smooth
stable welding arc.
Just what you’re
looking for, right?
Printed Circuit Board
–
Our solid state printed circuit
board can be removed and
installed in seconds, without
any tools for easy, do-it-
yourself service.
Main Relay Mechanism
–
One of the main reasons you
will fall in love with your MIG
welder. Imagine touching the
welding wire exactly where you
want to start welding, pulling
the trigger, and starting the
weld right there in that exact
spot. With a main relay, the
wire is not “electrically hot”
until you pull the trigger.
HTP’s Gear Drive Feed System
–
Used on all of our welders,
except the MIG 130. We don’t
use any plastic like many of our
competitors. Why? Because a
smooth consistent wire feed
results in a smooth stable arc.
Control Transformer
– Provides low voltage to run the printed circuit board,
wire drive motor, and main relay. While many companies take this voltage
from the main welding transformer, shortening the life of the transformer
and not providing as stable a voltage supply, our machines come standard
with this separate transformer.
Copper Windings in the
Main Transformer
–
800-USA-WELD | www.USAWeld.com
15
MIG Welders and MIG Welding Accessories
Reverse Polarity – Right on the front of the
welder, and without any tools – just in case
you want to use “gasless” flux-cored wires.
Full Undercarriage –
HTP includes wheels
and a gas bottle tray
as standard equip-
ment. If we didn’t,
how else would you
move your welder
around the shop to
your project?
Recessed Controls –
All of our potentiometers are
recessed, which helps prevent
accidental damage.
Stitch and Spot Welding –
Many other companies charge extra for these features, but at HTP they are standard
equipment. Why? Because it makes welding on light gauge sheet metal easier and
faster with less warpage and less chance of burn through.
10 ft. Coaxial Welding Gun –
The coaxial design of our welding
gun provides a smooth, consistent
wire feed – essential when it comes
to a nice, smooth, stable arc. Also,
you can remove and install the
welding gun without any tools,
which makes changing over to a
teflon liner for aluminum welding
easy.
16 Gauge Steel Cabinet –
We build our cabinets out of
16 gauge steel, not plastic
like a lot of our
competition, and, rather than
using sheet metal screws, we
MIG weld our cabinets –
resulting in a rugged
cabinet, designed for
years of use.
10´ Ground Cable – Easily removed
without any tools – an important feature
if you happen to drop something on it,
sever the cable, and need to replace it.
Powder Coated Cabinets –
We powder coat our
cabinets to keep your
welder looking good years
down the road.
The capability to braze steel, weld aluminum, steel, stainless steel and cast iron – without expensive add-on options.
The ability to handle 10 lb., 30 lb. or 40 lb. spools of wire.
A free welding DVD that actually gives you a “through the helmet” look at proper welding techniques and lets you
hear what to listen for – instructions that benefit both the beginner and pro. Also describes the operation, mainte-
nance of, and troubleshooting tips for your welder.
Our special toll-free service and assistance hotline: 1-800-USA-WELD. Expert advice, parts, and accessories are
only a phone call away!
Three-Year Warranty – HTP MIG welders have a three-year warranty, so you know they will keep working for you
down the road.
A coaxial welding gun available in 10’, 12’ or 15’ lengths.
90-Day Money-Back Guarantee: If for any reason you are not satisfied, we’ll take the machine back.
All welders have free shipping anywhere in the Continental United States.
All HTP MIG Welders Offer
Free Shipping* - All Orders Over $35*