403002-04-05-07-08-09-10_en_ma_2011 GRAVITY SLICERS 403.002 403.004 403.005 403.007 403.008 403.009 403.
CONTENTS FOREWORD ................................................................................................................3 SCOPE OF THIS MANUAL .......................................................................................3 GENERAL INFORMATION ..........................................................................................3 LIMITS OF USE-SAFETYNORMS .............................................................................3 GENERAL SAFETY REGULATIONS ..........................
FOREWORD SCOPE OF THIS MANUAL This manual contains all the necessary information to install, use and service the gravity slicers for food (please see models in paragraph "Technical Description"). The scope of this document, hereinafter the "manual", is to permit users, and especially end users, to take all the cautions and provisions possible for using this machine safely and for a long time.
MANUFACTURER'S WARRANTY AND LIABILITY The manufacturer's warranty covering the good functioning of the machines and their compliance to the service for which they have been designed depends on the correct application of the instructions contained in this manual.
PACKING OPENING THE BOX On reception check packaging integrity, otherwise inform the forwarding agent or the area agent immediately. To unpack the machine, proceed as follows: Open the box and remove your copy of the manual of use and maintenance, then proceed according to the instructions found on that manual; Lift the machine still wrapped in a transparent polyethylene sheet and extract it from the box; Now check the box content and make sure it corresponds to what shown on the external label.
TECHNICAL DESCRIPTION AND PROPOSED CONDITIONS OF USE GENERAL DESCRIPTION The machine is essentially made of a base supporting a circular blade mounted in tilted position. This blade is driven by an electrical motor to slice foodstuffs. The machine is equipped with a carriage holding a product tray and sliding on tracks mounted under the base top, parallel to the blade. Slice thickness is adjusted by means of a gauge plate mounted in front of the blade.
DIMENSIONS 403.002 403.004 403.005 403.007 403.008 403.009 403.010 MAIN TECHNICAL DATA 403002-04-05-07-08-09-10_en_ma_2011 GRAVITY SLICERS Version 403008 403007 403009 403002 403010 403004 403005 Motor HP Blade Ø mm Rpm Min.
SUPPLIED LITERATURE AND ACCESSORIES If not otherwise defined at the moment of order, the machines are supplied together with the following: EU conformity declaration Instructions manual for installation, use and maintenance. PRODUCTS THAT CAN BE SLICED All types of cold cuts (raw, cooked, smoked); Meat without bone (raw or cooked, at a temperature not less than + 3 °C; Cheese cuts (obviously types that can be sliced such as gruyere, fontina, etc.).
MAIN COMPONENTS I 403002-04-05-07-08-09-10_en_ma_2011 403.008 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. STARTUP BUTTON (GREEN) STOP BUTTON (RED) N.A. SLICE THICKNESS CONTROL KNOB ADJUSTABLE FOOT CARRIAGE TRAY SUPPORT BASE PRODUCT TRAY BLADE PLATE PRODUCT GRIP 11. BLADE 12. PRODUCT GRIP HANDLE 13. MANUFACTURER IDENTIFICATION PLATE, MACHINE DATA AND UE MARKS 14. PRODUCT GRIP HAND PROTECTION 15. PRODUCT TRAY HAND PROTECTION 16. PRODUCT TRAY HANDLE 17. BLADE PLATE TIE-ROD 18. SUPPLY CORD 19. GAUGE PLATE 20.
MAIN COMPONENTS 403002-04-05-07-08-09-10_en_ma_2011 403.002 403.004 403.005 403.007 403.009 403.010 1. 2. 3. 4. 5. STARTUP BUTTON (WHITE OR GREEN) STOP BUTTON (RED OR BLACK) N.A. SLICE THICKNESS CONTROL KNOB ADJUSTABLE FOOT 6. CARRIAGE TRAY SUPPORT 7. BASE 8. PRODUCT TRAY 9. BLADE PLATE 10. PRODUCT GRIP 11. BLADE 12. PRODUCT GRIP HANDLE IDENTIFICATION 13. MANUFACTURER PLATE, MACHINE DATA AND EU MARKS 14. PRODUCT GRIP HAND PROTECTION 15. PRODUCT TRAY HAND PROTECTION 16. PRODUCT TRAY HANDLE 17.
MACHINE COMMISSIONING AND FUNCTION TESTS INSTALLING THE MACHINE Position the machine on a well leveled, smooth and dry top suitably dimensioned to withstand the machine weight. ELECTRICAL CONNECTION Install the machine near a EU compliant outlet derived from a system meeting the current norms. The user is responsible for ascertaining that the electrical system is suitably dimensioned and functions correctly (supply line, outlet, distribution panel, differential protecting breaker, grounding).
COMMANDS START AND STOP BUTTONS Press the white or green button (1) to start running the blade. The light turns on to indicate that the machine works correctly. Press the red or black button to stop the blade. Slice thickness can be adjusted by turning the graduated knob (4) counterclockwise. Thickness adjustment range: see paragraph "Technical description and conditions of use”.
USING THE MACHINE LOADING THE PRODUCT ON THE TRAY AND SLICING 403002-04-05-07-08-09-10_en_ma_2011 Ascertain that the thickness control knob is correctly positioned to '0'. Draw back the carriage completely (towards the operator) to loading position. Lift the product grip by pulling it away by 10 cm from the blade and put it in rest position. Lay the product to be sliced against the wall on the operator side. Secure by means of the product grip by exerting a slight pressure.
CLEANING THE SLICER GENERAL The machine must always be accurately cleaned at least once a day, and more often if necessary. Always use protective gloves.
REASSEMBLING THE MACHINE Proceed as indicated for the previous operations but in reverse order. MAINTENANCE GENERAL The operator is allowed to perform the following maintenance operations: Blade sharpening: regularly (intervals and duration obviously depend on the use of the machine, time of use and type of product sliced); Lubrication of carriage sliding guides: once a week. Lubrication of product grip sliding bar: once a week. Adjustment of motor belt tension: as required.
SHARPENING Models with separate sharpener 1. Clean the blade accurately using denaturized alcohol to degrease it. 2. Turn the graduated knob (1) towards the left to open completely. 3. Remove the sharpener from its box, unscrew the knurled knob and insert the threaded metallic pin inside the hole (2) provided for on the product tray so that the two emery wheels are turned towards the blade. Snap into place by pressing on the lower wheel button (3).
SHARPENING Versions with built-in sharpener To sharpen the blade periodically as soon as the cutting capacity decreases. Please proceed as per the following instructions: 403002-04-05-07-08-09-10_en_ma_2011 1. After disconnecting form the mains, clean the blade accurately using denaturized alcohol to degrease it. 2. Loosen the knob (1) and turn the sharpener (2) by 180° and insert the whells on the slicer blade. Relock the knob. 3. Operate the switch (3) and press the button (4); 4.
LUBRICATION Carriage sliding guides product grip (once a week) Use only the oil provided, otherwise use white Vaseline oil. DO NOT USE VEGETAL OILS. 403002-04-05-07-08-09-10_en_ma_2011 Spread a small quantity of oil on the bar and move the assembly 3 or 4 times. Clean as required to remove excess of oil.
ADJUSTING THE MOTOR BELT TENSION 403002-04-05-07-08-09-10_en_ma_2011 After a given period of service an unusual noise may occur because of the belt bedding. In this case, tighten the belt-stretcher on the side of the motor under the machine base.
TROUBLESHOOTING AND REMEDIES 403002-04-05-07-08-09-10_en_ma_2011 The table below indicates the most common problems that may arise during slicing and the necessary remedies. PROBLEM POSSIBLE CAUSE REMEDY The machine does not start when the green button is pressed No power supply The blade guard is not correctly positioned. Defective electrical control circuit. Ascertain that the plug is is correctly inserted.
DISMANTLING THE SLICER These machines are made of the following elements: Aluminium frame; Stainless steel fittings and others; Electrical parts and cords; Electrical motor; Plastic materials, etc. Whether dismantling is entrusted to third parties or done in-house (in that last case you will have to separate the various materials) please note that disposal of the materials can only be carried out by duly authorized businesses. In any case, please comply to the current norms of your country.
ELECTRICAL DIAGRAM SIG. 97 (versions 403.002-7-8-9) 403002-04-05-07-08-09-10_en_ma_2011 Mod. 403.008 Mod. 403.007 Mod. 403.
