Speaker System User Manual

11
FUSSION 3000 SPECIFICATIONS
Line Input Power
US: 115V, 60Hz
Recommended Amperage Service:
20A recommended
AC Connector: 3-pin Twistlock
250VAC, 20A male
Europe: 230V, 50Hz
Recommended Amperage Service:
16A recommended
AC Connector: 3-pin IEC
250VAC, 16A male
In-rush Current Protection: Transistor-based
Safety Features
RMS Limiting: Monitoring and limiting
of continuous RMS
output of amplifiers
Thermal Protection: Input stage shutdown,
auto-reset
Physical Properties
Enclosure: Trapezoidal, 15º side
angles, 18mm multi-
layered birch
Hanging Inserts: 4 points on top
Rigging Inserts: 2 points, 1 each side
ATM MEGS
1 pull-back clip, bottom
Handles: 4 ea. aluminum/rubber
grips
Height: 41.9˝ (1064mm)
Front Width: 24.7˝ (628mm)
Rear Width: 13.9˝ (352mm)
Depth: 22.6˝ (575mm)
Weight: 246 lbs. (112kg)
Options
Active Subwoofer System:
FUSSION 1800SA/1800S
Flyware: ATM MEGS compatible
Disclaimer
Since we are always striving to make our
products better by incorporating new and improved
materials, components, and manufacturing methods,
we reserve the right to change these specifications at
any time without notice.
“Mackie,” the “Running Man” figure, and
“FUSSION” are trademarks or registered trade-
marks of Mackie Designs Inc.
All other brand names mentioned are trade-
marks or registered trademarks of their respective
holders, and are hereby acknowledged.
©2000 Mackie Designs Inc.
All Rights Reserved.
Printed in Italy.
System Acoustic
Frequency Range (–10 dB): 45Hz-20kHz
Frequency Response
(–3 dB): 55Hz-18kHz
Horizontal Coverage
(–6 dB): 80º averaged 2kHz-10kHz
Vertical Coverage (–6 dB): 70º averaged 2kHz-10kHz
Directivity Factor; DI (Q): 10.19 (10.46) averaged
2kHz to 10kHz
Maximum SPL (long term): 130 dB @ 1m
Maximum SPL (peak): 133 dB @ 1m
Maximum SPL (long term—High Pass ON): 132 dB
Maximum SPL (peak—High Pass ON): 135 dB
Crossover Points: 500Hz, 2500Hz
Dynamic Range: > 110 dB
Phase Response:
± 35º from 500Hz-10kHz
Transducers
Low-Frequency Transducers—Four Each
Cone Diameter: 12˝ (300mm)
Voice Coil Diameter: 3˝ (75mm)
Nominal Impedance: 8 ohms each
Power Handling: 350 watts rms (long term)
1
Mid-Frequency Transducer
Cone Diameter: 8˝ (200mm)
Voice Coil Diameter: 2˝ (50mm)
Nominal Impedance: 8 ohms
Power Handling: 150 watts rms (long term)
1
High-Frequency Transducer
Diaphragm Diameter: 3˝ (75mm)
Throat Exit Diameter: 1.4˝ (35.6mm)
Nominal Impedance: 8 ohms
Power Handling: 75 watts rms (long term)
1
Diaphragm Material: Titanium
Power Amplifiers
Low-Frequency Power Amplifier
Rated Power: 1000W continuous @ 8Ω
1500W peak @ 8Ω
Rated THD: < 0.03%
Mid-Frequency Power Amplifier
Rated Power: 200W continuous @ 8Ω
300W peak @ 8Ω
Rated THD: < 0.03%
High-Frequency Power Amplifier
Rated Power: 100W continuous @ 8Ω
150W peak @ 8Ω
Rated THD: < 0.03%
Audio Input/Output/Controls
Input Type: Balanced differential
Input Impedance: 50k ohms
Sub-Out: 85Hz low-pass output
with protection and active monitoring
for FUSSION 1800S/1800SA active
subwoofer system
Fill-Out: 85Hz high-pass output
Fill-Out Level: 0 dB to –30 dB
Fill-Out Phase Control: 0º/180º
High-Pass Switch: 85Hz high-pass to LF
driver
1
Power handling for transducers is based on an AES long term power
testing standard conducted for 100 hours full power, free air.