SWA1801 ACTIVE SUBWOOFER SYSTEM USER’S MANUAL ACTIVE LIMIT SIGNAL THERMAL PARALLEL THRU (FULL RANGE OUTPUT) SUBWOOFER CONTROL FULL RANGE INPUT POWER HIGH PASS (MID/HIGH FREQ) OUTPUT NORMAL 120Hz L L SUBWOOFER LEVEL IN OUT R NORMAL R REV 180 PHASE POWER ON SWA1801 ACTIVE SUBWOOFER 115V-AC FUSE AC125V-T6.3A DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA AND MACKIE EUROPE COPYRIGHT ©2000 • THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
CAUTION AVIS RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ATTENTION: POUR EVITER LES RISQUES DE CHOC ELECTRIQUE, NE PAS ENLEVER LE COUVERCLE. AUCUN ENTRETIEN DE PIECES INTERIEURES PAR L'USAGER. CONFIER L'ENTRETIEN AU PERSONNEL QUALIFIE.
Lend Me Your Ears Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a period of time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the permissible noise level exposures shown in this chart.
REAR PANEL DESCRIPTION POWER Switch Use this switch to turn the SWA1801 on and off. Make sure the signal source’s level control is turned down before you turn it on. AC power supply, this indicator lights green to let you know that you’re ready to rock and roll. The cool blue LED on the front of the cabinet works in the same way. FULL RANGE INPUT AC Receptacle This is where you connect the AC linecord to provide AC power to the SWA1801’s built-in power amplifiers.
HOOKUP DIAGRAMS SA1521 Plays the Mid and High Frequencies SA1521 Plays the Mid and High Frequencies Pole Mount Line-Level Mid/High Out Left Power Cord Pole Mount Line-Level Mid/High Out Right ACTIVE C300 Plays the Mid and High Frequencies Power Cord ACTIVE C300 Plays the Mid and High Frequencies Stereo Power Amplifier Pole Mount Pole Mount ACTIVE ACTIVE Line-Level Hi-Pass Out Full Range Right Full Range Left Full Range 1202-VLZPRO 1202-VLZPRO SWA1801 Plays the Low Frequencies SWA1801 P
CONNECTIONS The SWA1801 has two female XLR inputs that accept a balanced line-level signal. When connecting a balanced signal, be sure it’s wired per AES (Audio Engineering Society) standards: XLR Hot (+) Pin 2 Cold (–) Pin 3 Shield (Ground) Pin 1 The THRU output connectors allow you to connect more than one SWA1801 to your system. Simply plug the signal source (i.e.
AC POWER Be sure the SWA1801 is plugged into an outlet that is able to supply the correct voltage specified for your model. If the voltage should drop below 97% of the specified line voltage, the built-in amplifiers will no longer be able to supply rated power. (They will continue to operate down to 80% of the rated line voltage, but won’t reach full power, resulting in lower headroom.) Be sure the electrical service can supply enough amperage for all the components connected to it.
No sound Noise • Is the input LEVEL control for the input source or the subwoofer turned all the way down? Verify that all the volume controls in the system are properly adjusted. • Is the signal source working (and making union scale)? Make sure the connecting cables are in good repair and securely connected at both ends. Make sure the output volume (gain) control on the mixing console is turned up sufficiently to drive the inputs of the speaker.
Repair Service for Mackie products is available at a factory-authorized service center. Service for Mackie products living outside the United States can be obtained through local dealers or distributors. If your SWA1801 needs service, please follow these instructions: 1. Review the preceding troubleshooting suggestions. Please. 2. Call Tech Support at 1-800-898-3211, 7am to 5pm PST, to explain the problem in detail. They will ask you all sorts of impertinent questions in the hope of sorting out the problem.
SWA1801 SPECIFICATIONS Enclosure Geometry Rectangular Mounting Methods Floor mount only System Specifications Frequency Range (–10 dB) 35 Hz–120 Hz Frequency Response (–3 dB) 45 Hz–120 Hz Maximum SPL @ 1m 129 dB Peak Output @ 1m 135 dB Crossover Frequency 120 Hz (12 dB/octave) Input Type Balanced differential Input Impedance 50 kΩ Input Protection Level protected Thermal Protection Input stage muting, auto-reset Transducer Specifications Low-Frequency Transducer Diameter Voice Coil Diameter 18˝ (457 mm)
SWA1801 LIMITED WARRANTY Please keep your sales receipt in a safe place. A. LOUD Technologies Inc. warrants all materials, workmanship and proper operation of this Mackie SWA1801 for a period of five years from the original date of purchase, with the following exception: warranty on all its loudspeaker components including woofers and compression drivers are only warranted for two years.
16220 Wood-Red Road NE • Woodinville, WA 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 • www.mackie.com E-mail: sales@mackie.