Thump12BST • Thump15BST 1300W Advanced Powered Loudspeakers OWNER’S MANUAL
Thump12BST • Thump15BST Powered Loudspeakers Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Features Important Safety Instructions .................................. 2 Contents / Features ................................................ 3 Introduction / Getting Started ................................. 4 Hookup Diagrams .................................................... 5 Thump12BST / Thump15BST: Rear Panel Features .. 10 Thump Connect App ......................................... 10 1. Power Connection ....................................... 10 2. Power Switch .................................
Thump12BST • Thump15BST Powered Loudspeakers Introduction Getting Started Delivering proven, chest-thumping low-end with Dynamic Bass Response™ technology in all-new, professional enclosures, the 1300W Thump™ loudspeakers take the series to a whole new level. The following steps will help you set up the loudspeakers quickly. Get maximum versatility with built-in mixers and application-specific speaker modes.
Owner’s Manual Hookup Diagrams SPEAKER VOICING MUSIC W/ SUBWOOFER MUSIC LIVE SPEECH + SUB + SUB MON SPEAKER VOICING MUSIC W/ SUBWOOFER MUSIC LIVE SPEECH + SUB + SUB MON Thump loudspeakers are the perfect tool for singer-songwriters touring the local coffee shops. Bring your favorite axe and mic, Thump loudspeakers and cables and power cords. In this example, a dynamic microphone is connected to the channel 1 input of a Thump12BST loudspeaker, used for monitoring purposes.
Thump12BST • Thump15BST Powered Loudspeakers Hookup Diagrams continued... SPEAKER VOICING MUSIC W/ SUBWOOFER MUSIC LIVE SPEECH + SUB + SUB MON LINE HI-Z In this example, a ProFX8v2 mixer is connected directly to two Thump12BST loudspeakers. It is the perfect setup for a small club or... a fun karaoke house party! Simply connect the L/R outputs of the ProFX8v2 mixer to the CH1 input of each Thump12BST loudspeaker.
Owner’s Manual Hookup Diagrams continued... SPEAKER VOICING MUSIC W/ SUBWOOFER MUSIC LIVE SPEECH + SUB + SUB MON Perhaps you’re a DJ playing bumpin’ tunes in the middle of the night to a crowd that’s groovin’ and dancin’ to your fine selection. In this example, a laptop is connected to the bluetooth channel of a Thump15BST loudspeaker which, in turn, is linked to another Thump15BST loudspeaker.
Thump12BST • Thump15BST Powered Loudspeakers Hookup Diagrams continued... To next Thump loudspeaker input To next Thump loudspeaker input Main Outs 1402VLZ4 Mixer To next Thump loudspeaker input Thump loudspeakers may be daisy-chained via the male XLR connector labeled “MIX OUT”. Simply plug the signal source (i.e., mixer output or microphone) into the input jack(s), and patch that loudspeaker’s mix out jack to the next loudspeaker’s input jack, and so on, daisy-chaining multiple Thump loudspeakers.
Owner’s Manual Hookup Diagrams continued... SPEAKER VOICING MUSIC W/ SUBWOOFER SPEAKER VOICING MUSIC W/ SUBWOOFER MUSIC LIVE SPEECH MUSIC LIVE SPEECH + SUB + SUB MON + SUB + SUB MON Here’s how to set up a large club system. In this example, the L/R outputs of a DL1608 mixer are connected directly to the CH1 inputs of a pair of Thump15BST loudspeakers. The Speaker Modes of these PA loudspeakers may be set to Music + Sub.
Thump12BST • Thump15BST Powered Loudspeakers Thump12BST / Thump15BST Loudspeakers: Rear Panel Features 2. Power Switch 5 6 3 4 Press the top of this rocker switch inwards to turn on the loudspeaker. Press the bottom of this rocker switch inwards to turn off the loudspeaker. As a general guide, the mixer (or other signal source) should be turned on first, subwoofers next, and loudspeakers last. As such, the loudspeakers should also be turned off first, followed by the subwoofers, then the mixer.
To connect unbalanced lines to these inputs, use a 1/4" mono (TS) phone plug, wired as follows: 1/4" TS Unbalanced Mono Wiring: Sleeve = Shield Tip = Hot (+) SLEEVE SLEEVE TIP TIP TIP SLEEVE NEVER connect the output of an amplifier directly to a Thump’s input jack. This could damage the input circuitry! 5. LCD Display This modern, high-resolution, all-color TFT LCD Display is one of the most vital features of the ThumpBST loudspeaker.
Thump12BST • Thump15BST Powered Loudspeakers Speaker Control Functions Mixer Screen The following list provides the high level navigation items, in order, on the user interface and their subsequent user controlled parameters. As seen in the first screen shot to the left, the mixer screen is a representation of a mixer...
Now, the bottom row also houses input channels 1, 2 and BT. But instead of raising or lowering levels, this is where to adjust each channels’ EQ. Additonally, this is where to access the Menu screen. 1 2 BT Main 1 2 BT Main As seen below, we changed the channel 1 high, mid and low EQ to +5 and the HPF setting to 110 Hz. Press the speaker control knob to return to the previous screen once the EQ settings you desire have been dialed in.
Thump12BST • Thump15BST Powered Loudspeakers Speaker Mode Menu Screen The menu screen displays six icons. Like the mixer screen, just rotate the speaker control knob until the icon of the parameter you want to change is illuminated. Then push the knob to enter that icon’s screen. Speaker mode allows you to change the loudspeaker’s speaker mode to tailor it to best suit your particular application.
This is where to set up and view wireless connectivity options for the devices and speakers. MIXER MODE CONFIG LOCK Notice how the icon of the device also illuminates when paired. BT LCD Below is a list of the parameters that may be edited: Device – The device may either be paired or not paired. To pair: (1) Make sure “connect” is illuminated and push the speaker control knob. NOT PAIRED CONNECT NOT LINKED CONNECT BT MODE: ZONE (2) The text “not paired” will change to “discoverable...
Thump12BST • Thump15BST Powered Loudspeakers (3) The text “searching...” will change to “primary” on one loudspeaker and “secondary” on the other. Also, “cancel” will change to “disconnect”. From here, you can either (A) select a Bluetooth mode (see below), or (B) push the speaker control knob to disconnect. NOT PAIRED CONNECT NOT PAIRED CONNECT PRIMARY DISCONNECT BT MODE: ZONE SECONDARY DISCONNECT BT MODE: ZONE Notice how the icon of the loudspeaker also illuminates when linked.
This is where to configure each speaker’s LED status, auto connect / link bluetooth and more. MIXER MODE CONFIG LOCK BT LCD Auto Link BT – Allows two previously paired speakers to automatically re-link if both are powered on and in range. When illuminated, push the speaker control knob to select between on or off.
Thump12BST • Thump15BST Powered Loudspeakers Lock LCD This is where to lock and unlock the interface with a secret 4-digit numeric password. On the bottom-right is the LCD screen, where you may change the settings for the screen saver and (mixer and menu) home screen. MIXER CONFIG MODE LOCK BT MIXER MODE BT CONFIG LOCK LCD LCD Locking – Push the speaker control knob to enter lock mode.
LCD SETTINGS Brightness: LOW Home Screen: 1 2 BT After pushing the speaker control knob on the BBQ screen, you will see something that looks like this: Main Food: MIXER Owner’s Manual Both screens were shown and described several pages ago, but they’re shown again below. BBQ SETTINGS STEAK Beverage: Game: BEER CROQUET Mixer The editable parameter on top is food. Push the speaker control knob again to edit the food.
Thump12BST • Thump15BST Powered Loudspeakers Protection Circuitry AC Power Thump loudspeakers employ a built-in limiter for less distortion at peak levels. A dynamic bass response circuit provides optimal low frequency response regardless of overall output level. Additional protection includes automatic thermal shutdown should the amp overheat. However, with Class-D amp technology, which is highly-efficient, this should never be a problem.
WARNING: Installation should only be done by an experienced technician. Improper installation may result in damage to the equipment, injury or death. Make sure that the loudspeaker is installed in a stable and secure way in order to avoid any conditions that may be dangerous for persons or structures. Thump loudspeakers are designed to sit on the floor or stage as the main PA or as monitors. They may also be pole-mounted via the built-in socket on the bottom of the cabinet.
Thump12BST • Thump15BST Powered Loudspeakers 22 Room Acoustics Thump loudspeakers are designed to sound fantastic in nearly every application. • But, room acoustics play a crucial role in the overall performance of a sound system. However, the wide highfrequency dispersion of the Thump loudspeakers helps to minimize the problems that typically arise.
Rigging Hardware and Accessories WARNING: Installation should only be done by an experienced technician. Improper installation may result in damage to the equipment, injury or death. Make sure that the loudspeaker is installed in a stable and secure way in order to avoid any conditions that may be dangerous for persons or structures. Rigging our loudspeakers will invariably require hardware not supplied by us. Various types of load-rated hardware are available from a variety of third-party sources.
Thump12BST • Thump15BST Powered Loudspeakers Appendix A: Service Information If you think your Thump loudspeaker has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website (www.mackie.com/support) where you will find lots of useful information such as FAQs and other documentation. You may find the answer to the problem without having to part with your loudspeaker.
Thump12BST / Thump15BST Loudspeakers Specifications Acoustic Performance Input/Output Frequency Range (–10 dB): 50 Hz – 23 kHz [Thump12BST] 32 Hz – 23 kHz [Thump15BST] Input Type: Frequency Range (–3 dB): 57 Hz – 20 kHz [Thump12BST] 39 Hz – 20 kHz [Thump15BST] Mic-Line Impedance: Horizontal Coverage Angle: Vertical Coverage Angle: Maximum SPL Peak: 8 k balanced Impedance: 90º Mix Out: 60º Mix Out Impedance: 126 dB [Thump12BST] 127 dB [Thump15BST] Monitor Angle 1/4" TS, Wide-Z™ 2x Female XL
Thump12BST • Thump15BST Powered Loudspeakers Thump Loudspeaker Specifications continued... Physical Properties Options Thump12BST: Thump12BST Speaker Bag P/N 2047360-09 Height: 24.2 in / 615 mm Thump12BST Rolling Speaker Bag P/N 2047360-10 Width: 14.1 in / 358 mm Thump15BST Speaker Bag P/N 2047360-11 Depth: 14.0 in / 356 mm Thump15BST Rolling Speaker Bag P/N 2047360-12 Weight: 29.3 lb / 13.3 kg SPM200 Loudspeaker Pole Mount P/N 2035170-01 Height: 27.
Music Speaker Mode – This mode is full range, but focuses on increased bass and brilliant high frequencies. This is the place to start for most DJ / music playback applications. Live Speaker Mode – This mode features a low frequency roll-off to get rid of unwanted thumps and adds boost and sparkle to mid-range and high frequencies. This mode is perfect for plug-and-play singer-songwriters.
Thump12BST • Thump15BST Powered Loudspeakers User EQ Digitallycontrolled Preamp User EQ User EQ Digitallycontrolled Preamp 3x1 mixer with user controlled input gains 6 user selectable voicings Crossover LF Equalization HF Equalization Master Gain Limiter Limiter Mute Mute Thermal Monitoring Amp Amp Thump12BST • Thump15BST Powered Loudspeakers LF HF Thump12BST / Thump15BST Loudspeakers Block Diagram
Please keep your sales receipt in a safe place. This Limited Product Warranty (“Product Warranty”) is provided by LOUD Technologies Inc. (“LOUD”) and is applicable to products purchased in the United States or Canada through a LOUD-authorized reseller or dealer. The Product Warranty will not extend to anyone other than the original purchaser of the product (hereinafter, “Customer,” “you” or “your”). For products purchased outside the U.S. or Canada, please visit www.mackie.
16220 Wood-Red Road NE Woodinville, WA 98072 • USA Phone: 425.487.4333 Toll-free: 800.898.3211 Fax: 425.487.4337 www.mackie.
FAQ Thump Series http://www.mackie.com/products/thump What models are featured in the Thump Series? The Thump Series will consist of four powered loudspeakers and one powered subwoofer: • • • • • Thump12A 1300W 12" Powered Loudspeaker Thump15A 1300W 15" Powered Loudspeaker Thump12BST 1300W 12" Advanced Powered Loudspeaker Thump15BST 1300W 15" Advanced Powered Loudspeaker Thump18S 1200W 18" Powered Subwoofer www.mackie.com PHONE: 425.487.4333 • TOLL-FREE: 800.898.
FAQ Thump Series http://www.mackie.com/products/thump What different configurations are there for the Thump loudspeakers? All models come with flexible mounting options including tripod and pole-mounting and work with the standard 35mm tripod and pole-mount size. What pole should I use with my Thump loudspeakers? Thump loudspeakers are compatible with the SPM200 pole mount.
FAQ Thump Series http://www.mackie.com/products/thump What is the screen used for on the Boosted models? The speaker’s user interface consists of a push-button rotary encoder combined with a backlit screen allowing the user to access functions such as channel and master level control, metering, 3-channel digital mixer & EQ, wireless configuration, setup functions and product info.
Thump Series FAQ http://www.mackie.com/products/thump What are application specific speaker modes? The different modes, basically, are applying a specific EQ curve to the sound of the speaker that will help it to be better suited for your application. There are six application-specific speaker modes that voice the Thump Boosted speakers and four that voice the Thump12A/15A models, allowing your Thump loudspeakers to sound and perform at their best for your application.
Thump Series FAQ http://www.mackie.com/products/thump What is the EQ on the Thump Boosted models used for? Thump Boosted gives you the ability to adjust each input with a 3-band channel EQ plus variable high-pass filters on Ch. 1/2. The on-board 3-band EQ is great for making minor adjustments to input channels to accommodate for a particular environment that the speakers are being used in.
FAQ Thump Series http://www.mackie.com/products/thump Is it normal for the speaker to “pop” when it is switched on or off? It is normal for the Thump speakers to emit a slight “pop” when it is powered up or down. The pop is caused by electricity left inside the amplifier circuitry discharging to the speaker. We do suggest if you are using the Thump18S subwoofer with a Thump12A or Thump15A, to make all connections before powering anything on.
Thump Series FAQ http://www.mackie.com/products/thump What Bluetooth protocol is used in the Thump Boosted (not available on the Thump12A/15A)? The new Mackie Thump Boosted use the latest in Bluetooth chipsets to deliver an impressive feature set. Class-1 speaker linking – an important performance specification for Bluetooth chips sets is the transmission power output, which is it’s “class” rating.
