Specification Sheet

ManualsBrandsMacroreer ManualsComputers & AccessoriesMacroreer for Arista CAB-SFP-SFP-1M 10GBASE-CR Direct Attach Copper Cable Passive SFP+ DAC Cable 1-meter

www.macroreer.com

info@macroreer.com

MX-SFP-PXM

SFP+ Direct Attach Passive Copper Cables,0.5m,1m,3m,5m,7m,10m Reach

Overview

The DAC SFP+ cable assemblies are high-performance, cost effective I/O solutions for 10Gb Ethernet and 10G Fibre Channel

applications. SFP+ passive copper modules allow hardware manufacturers to achieve high port density, configurability and

utilization at a very low cost and to reduce power budget. The high-speed cable assemblies meet and exceed the performance and

reliability requirements stipulated by Gigabit Ethernet and Fibre Channel industry standard.

Features

·SFF-8431 Compliant

·Broadband serial data rate operation:10 Mbps to 12 Gbps

·Data rates backward compatible to 1Gbps

·Hot-pluggable SFP 20PIN footprint

·Power Level I: 15 mW per cable end

·100 Ohm differential impedance

·Retractable pin latch

·EEPROM signature

·Pull to Release latch design

·360°cable braid crimp

·Enhanced EMI skirt design

·Color options for strain relief and pull tab

·Linear design for use with EDCs· AC-coupled inputs and outputs

·30AWG to 24AWG cable available

·Temperature Range: 0~ 70 °C

Summary of content (4 pages)

PAGE 1
MX-SFP-PXM SFP+ Direct Attach Passive Copper Cables,0.5m,1m,3m,5m,7m,10m Reach Overview The DAC SFP+ cable assemblies are high-performance, cost effective I/O solutions for 10Gb Ethernet and 10G Fibre Channel applications. SFP+ passive copper modules allow hardware manufacturers to achieve high port density, configurability and utilization at a very low cost and to reduce power budget.
PAGE 2
Applications ·10 Gigabit Ethernet and Gigabit ·Ethernet (IEEE 802.3ae) ·Fiber Channel: 1, 2, 4, 8, and 10GFC ·Infiniband SDR, DDR, and QDR ·Fiber Channel over Ethernet (FCoE) ·Serial data transmission Recommended Operating Conditions Systems Performance Media 10.5 Gpbs line speed, full duplex Hot-pluggable, industry-standard Small Form-Factor Bit error rate: better than 10E-12 Pluggable(SFP+) copper cable, available as 1m,3m or 5m.
PAGE 3
18 19 CML-I CML_I TD+ TD- Transmitter Data Non-Inverted Transmitter Data Inverted VeeT Transmitter Ground 20 1. Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor 2. Passive cable assemblies do not support LOS and TX_DIS Pin Description Tx_Fault: Tx_Fault is an output pin to indicate a fault condition of a laser.This pin is connected to ground in the module. Tx_Disable: x_Disable is an input pin to disable the transmitter output.
PAGE 4
Mechanical Dimensions Ordering information Part Number Product Description MX-SFP-P1M SFP+ Direct Attach Passive Cable (10GSFP+Cu), 1m, AWG:30 , 0ºC ~ +70ºC MX-SFP-P2M SFP+ Direct Attach Passive Cable (10GSFP+Cu), 2m, AWG:30 , 0ºC ~ +70ºC MX-SFP-P3M SFP+ Direct Attach Passive Cable (10GSFP+Cu), ,3m, AWG:30 , 0ºC ~ +70ºC MX-SFP-P3M SFP+ Direct Attach Passive Cable (10GSFP+Cu)，3m, AWG:24, 0ºC ~ +70ºC MX-SFP-P5M SFP+ Direct Attach Passive Cable (10GSFP+Cu), 5m, AWG:24 , 0ºC ~ +70ºC MX-SFP-P7M