MAD Gaze Watch Gesture Controlled Smart Watch USE GUIDELINES WATCH USE GUIDELINES (v2020.
Table of Contents Package Overview 3 Hardware Specification 4 Product Registration 6 Product Description 7 Product Guidelines 7 Dial Setting 9 Menu 10 MAD Fitness Application 12 Hand Gesture Control 13 Mobile Connection and Training 14 Navigate The Connected Device On Watch 19 Reconnect And Disconnect 23 Retrain Certain Gesture 24 Retrain All Hand Gestures 26 Shortcut Mode Setting 27 Gesture Media Control On Watch 29 Walkie-Talkie Application - Zello 31 Tutorial Video Sourc
Package Overview The package includes the following items: 1. 2. 3. 4. MAD Gaze Watch smart watch Charging cable Data Transmission Cable Watch Band (Regular) x1 x1 x1 x1 * Please use only MAD Gaze authorized accessories. * The use of unauthorized accessories may cause performance problems and failures, which are not covered by the warranty. * Avoid using fast chargers, only charge the watch with 5V1A output chargers.
Hardware Specification Product Model: W100 CPU: Quad Core 1.25GHz Operating System: Android 7.1 RAM: 1GB Storage: 16GB Screen: 1.39 inch Capacitive Touch Screen 260,000 Colors 400x400 pixels Resolution Sensors: Accelerometer and Gyroscope, Heart Rate Monitor Battery: Capacity: 620mAh Autonomy: 90 hours Standby Time; 48 hours Working time Wireless Connection: Bluetooth 4.0 Wi-Fi 2.
Product Appearance WATCH USE GUIDELINES (v2020.
Product Registration Please register your device to activate warranty within 7 days upon purchase date, otherwise, your device might not be covered under MAD Gaze Warranty. One device can only be registered under one MAD ID account. For details of Warranty Terms, please read Warranty on page 31. You will be required to enter the serial number of Watch when registering for the product warranty service. Follow the steps below to find the watch serial number: 1. Enter Settings on Watch 2.
Product Description Product Guidelines 1. Press and hold the upper button for 3 seconds to activate the watch. During the first time of the setup process, the Watch system might take a longer time to configure parameters. Please wait patiently. 1.1. 1.2. 1.3. 1.4. 2.
3. Product Guidelines To maneuver on Watch, swipe from the edge of the display screen and slide over half of the screen. Sliding only the middle of the display screen may not trigger certain tasks. 3.1. 3.2. 3.3. 3.4. Swipe right to enter the main menu; Swipe right twice to enter sports mode; Swipe right to access the synchronised content from phone and display it on Watch notification; Swipe down to view the Watch shortcut menu; Swipe left to view different shortcuts in the menu. 3.4.1. 3.4.2. 3.4.3.
4. Swipe up to access fitness data; then swipe left to view the step count, daily mileage and calories burnt. 5. Swipe right to quit the shortcut menu. Dial Setting Press and hold the dial screen to enter the dial setting. Users can manage the appearance and setting of the dial according to their preferences. Download new Watch face from the server (this requires network data): Press and hold the dial screen to enter the dial setting. Swipe left till the end to see a blue “+” sign.
Menu Contacts: 1. Create contacts to save names, phone numbers and more 2. Manage and edit contacts information 3. Sync your mobile contacts to the watch (only applicable on Android phones.) Phone: Dial phone calls (only applicable when a SIM card is inserted.) Messages: Send messages to your contacts (only applicable when a SIM card is inserted.) Settings： 1. Sound: Adjust the volume; 2. Display: Adjust the display brightness; 3. App List Style: Change the display interface; 4.
Downloads: Download documents and files from the internet; Calendar: Sync the events from your mobile calendar, swipe up or down to switch the month; Clock: View the current time, swipe right to the alarm and left to the stopwatch and timer; Gallery: View your mobile photos; Music: Listen to your mobile music; Sound Recorder: Built-in recorder to record sound; File Manager: View the storage status and manage files and folders on Watch; Heart Rate Monitor: Heart rate detection and sync the data to the connec
MAD Fitness Application 1. Download the app for synchronising your mobile data on Watch Pair Watch and your mobile by scanning the QR code to download MAD Fitness on your mobile. ● MAD Fitness App is only used for data synchronization between Watch and the mobile phone during use, which will not consume mobile network data. ● Downloading mobile apps requires cellular data usage. It is recommended to download when connecting to a Wi-Fi network.
c. Precautions i. Before the connection process, please disconnect all connected devices on Watch and the mobile. ii. Open the QR code interface on Watch and MAD Fitness app on mobile for connection. iii. Press the “Repair” button on MAD Fitness app if you want to change the connected device of Watch. After repairing the new device, other applications will sync the connection automatically. iv. Do not connect Watch with iPhone if it is under low power mode. v.
Mobile Connection and Training In order to enhance the accuracy of detecting your hand gestures, users are required to complete a 5 minutes hand gesture calibration training before use. 1. Install MG Watch app to your mobile from App Store or Google Play. Android iOS 2. Turn on the Bluetooth and open MAD Gaze Controller app on Watch. You will see a pair QR code when you first activate the Watch. WATCH USE GUIDELINES (v2020.
3. When there is a new released update of the MAD Gaze Controller, please connect MAD Gaze Watch to Wi-Fi or network data. Open the MAD Gaze Controller, an update message will pop up (as shown on the left), click "UPDATE NOW", then click "INSTALL" (as shown on the right) to complete the installation. 4. Turn on the Bluetooth and open MG Watch on mobile. 5. Open MG Watch on your mobile. Press “Start” to enter the pair interface.
6. After pairing, the watch icon will change to a phone icon on Watch. 7. Open MG Watch on mobile. Follow the instructions to start the calibration training. 8. Watch interface will display the following screen when the training is in progress. WATCH USE GUIDELINES (v2020.
9. Please follow the instructions shown in the tutorial videos to train different gestures on Watch. During the gesture training, please keep each gesture at the same position and strength, and keep about 1 second of interval between each gesture or movement. After receiving each training signal, the app will show the number of completing signals and the complete percentage of the entire training process.
11. After completing the training, read the instructions carefully and follow the procedures. 12. The below interface indicates that the entire training is completed. WATCH USE GUIDELINES (v2020.
Navigate The Connected Device On Watch 1. Open “Accessibility Setting” on your mobile. Turn on MG Watch to enable the access on Watch. 2. Turn on the Detect Mode on Watch to manipulate your connected device with hand gestures. WATCH USE GUIDELINES (v2020.
3. When the training gestures are well detected, different signals will be displayed on screen. For instance, *If the gesture signal was shown but it failed to manipulate on phone, please restart the “Accessibility Service” on mobile and try again. 4. If the watch cannot detect any gesture for 10 seconds under the detect mode, it will automatically enter sleep mode and turn off the detection. 5.
MAD Gaze Watch Interfaces Indication The watch has not connected to any device yet. (Green in background) The watch has already connected with your mobile and the detect mode is on. The watch has already connected with your mobile but entered sleep mode. WATCH USE GUIDELINES (v2020.
Hand Gestures Instruction Guidelines WATCH USE GUIDELINES (v2020.
Reconnect And Disconnect If the Bluetooth signal is interrupted, such as shutting down the watch or mobile, MAD Gaze Watch status will be shown as Disconnected in the homepage. The phone icon on your Watch will also change to Watch icon. If you’d like to reconnect the device, tap the watch icon and “Reconnect” button to repair your mobile. If you’d like to disconnect your mobile, tap the “Disconnect” button on image 3. WATCH USE GUIDELINES (v2020.
Retrain Certain Gesture If you found a certain gesture was not detected accurately, you may need to retrain the gesture again. 1. Open “Gesture Control Setting” 2. Enter “System Control” 3. Turn on the Detect Mode on Watch WATCH USE GUIDELINES (v2020.
4. Select the gesture you would like to retrain. 5. Press the “Retrain” button and enter the calibration interface. 6. After completion, you can test the gesture on the Gesture Test. WATCH USE GUIDELINES (v2020.
Retrain All Hand Gestures Press the “Phone/Watch” on your Watch, enter the connection interface and press the “Forget” button (image 2) to forget the device. Then both your Watch and mobile phone will be reset to the first time setup procedures. WATCH USE GUIDELINES (v2020.
Shortcut Mode Setting 1. Press “Gesture Control Setting” to enter the Shortcut mode menu. 2. Select a gesture shortcut. WATCH USE GUIDELINES (v2020.
3. Press ”Select an app” to select your customised app from the list. 4. Repeat the above steps to customise your app shortcuts. 5. Tap the right side of your forearm twice to enter Shortcut Mode, then act the preset gesture shortcuts to trigger certain tasks. After the shortcut was triggered, the watch will switch back to Normal mode. If you’d like to access the shortcuts again, please tap twice on the right side of your forearm again.
Gesture Media Control On Watch If MAD Gaze watch is not connected with any device, users are able to control the media playback on Watch with hand gestures, such as volume adjustment, track control and more. 1. Press “Accessibility Service” 2. Press “MAD Gaze Controller” 3. Switch on the “Accessibility Service” 4. Turn on the Detect Mode. Press the home button and return to the menu. 5. You may now access media control by hand gestures on Watch. WATCH USE GUIDELINES (v2020.
As you need to open MAD Gaze connector app to access gesture control, you may want to run the app in background so as to trigger gesture shortcuts even when you quit the app. Follow the steps below to do so: 1. Go to "System Optimization" on Watch 2. Enter "CleanTask" 3. Turn off "Battery Saver" After that, the app will keep running in watch background for gesture controls. WATCH USE GUIDELINES (v2020.
Walkie-Talkie Application - Zello In spite of connecting with your smartphone, MAD Gaze Watch can also operate independently. Disconnect Bluetooth from all the devices, then you can manage the watch applications by gesture control. For instance, Walkie-talkie application Zello, media control and more. 1. Open MAD Gaze Controller in your Watch, click the red button “Accessibility Service” and choose MAD Gaze Controller as below. 2.
3. Switch on the Detect Mode on Watch. 4. Press the upper Home button on Watch and return to the main menu. 5. Open the application Zello. 6. Then long press the upper Home button for two seconds to enter the control center. Press the circle button on top to switch your watch interface to square. Press the Home button to return to Zello. WATCH USE GUIDELINES (v2020.
7. Press “Options” in Zello. Enter “Push-to-talk buttons” and select “Toggle” from the “Screen button” list. Then return to Zello. 8. Set up for Zello app is completed. Please visit the link below for Zello user guide. https://support.zello.com/hc/en-us/articles/230749047-Zello-Android-User-s-Guide- 9. To quit Zello application, long press the upper Home button for two seconds to enter the control center. Press the square button on top to switch your watch interface to circle and enter full screen mode.
Tutorial Video Source Gesture Calibration and Enable Accessibility Service: https://youtu.be/i8N5TVDdygE Camera Control: https://youtu.be/KvE7hX6d-Aw Zello Walkie-Talkie Settings: https://youtu.be/irtoNwKOGTY Answer/reject phone calls: https://youtu.be/jDQ-FMmd0OI Media Control: https://youtu.be/dmGzKAZ5nD8 Shortcuts for applications: https://youtu.be/QqWQi9QW5RE WATCH USE GUIDELINES (v2020.
Troubleshooting The following frequently asked questions are designed to assist users for better understanding regard to the Watch setup and manipulation. If the problem cannot be solved after referring to the questions, please contact us at cs@madgaze.com. Q：What to do when MAD Gaze Watch does not turn on? A：Verify your Watch has a sufficient charge. Charge MAD Gaze Watch with the authorized charging cable, press the power button for more than 3 seconds to turn on Watch after a few minutes.
Q：What to do if MAD Gaze Watch cannot remote control my smartphone? A：Please confirm the connection status of MAD Gaze Watch and your smartphone. A mobile graphic will be shown on the watch interface if the connection succeeded. Or else, it will be shown as a watch graphic instead. Open the Detect Mode on Watch, switch off and on again the Accessibility Service on your smartphone. Q：Do I need to train my MAD Gaze Watch everytime before use? A：No.
Q：What is the difference between MG Watch and MAD Fitness? A：MG Watch is designed for gesture training and device connection while MAD Fitness is designed for calculating your health information like steps count, heartbeat and more. WATCH USE GUIDELINES (v2020.
Warranty ➢ We will provide an all-round Three Guarantees Service for your MAD Gaze Watch according to "The Warranty Regulations of Three Guarantees" enacted by relevant authorities in the People's Republic of China. ➢ Warranty Period will be counted from the day the product is activated*, for one year. The valid warranty period can be checked up on MAD Gaze Connector or "My Device" on MAD Store.
Limited Warranty ➢ Your warranty services are valid under normal usage/application only, the following conditions are excluded from the Three Guarantees and there will be reasonable charge for the warranty service: ○ The free maintenance period of the product has expired. ○ Mechanical failure due to application of fittings not recognised by our company. ○ Damage caused by disassembling the product by repairer who is unauthorized by our company.
➢ MAD Gaze Watch supports Nano SIM card, China Mobile 4G network, China Unicom 4G network, China Telecom 4G network, WCDMA 3G network and GSM 2G network. ➢ Watch battery capacity is limited due to the product size. It is recommended to turn off the energy-consuming function when unnecessary. Only apply GPS, Bluetooth, Wi-Fi functions according to personal habits. Please note that it may have a higher energy consumption and product temperature when Watch is downloading from a Wi-Fi or 4G network.
FCC Compliance Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
