Owner's Guide Mustang & Kenwood radio RETAINS STEERING WHEEL CONTROLS, SYNC MEDIA PLAYER, SYNC BLUETOOTH AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE •iDatalink Maestro RR Radio Replacement Interface •MUS1 Dash Kit •None ADS-RR(SR)-FOR01-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used herein are the properties of their respective owners.
TABLE OF CONTENTS WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. This guide is a great addition to both the vehicle owner’s guide and the aftermarket radio owner’s guide. We recommend having both these documents handy as they cover all the functionality that the Maestro RR retains.
USIING YOUR STEERING WHEEL CONTROLS USING YOUR STEERING WHEEL CONTROLS (If equipped) Your steering wheel buttons can be used to control your aftermarket Kenwood radio. You can assign steering wheel buttons to Kenwood radio functions. Simply program your Maestro RR module online using the Weblink updater and customize your buttons. Each steering wheel button can control up to two radio features.
MUS1 KIT FEATURES MUS1 KIT FEATURES BUTTON BAR Button functions There are 5 programmable buttons on the MUS1 dash kit. The button on the left and on the right of the button bar are hard coded for climate and rear defrost. All 5 buttons can be programmed for 2 functions, a push and release and a push and hold for 2 seconds. Climate button Pressing the climate button located on the left of the button bar will switch the radio to the climate screen.
USING YOUR FACTORY SYSTEMS USING YOUR FACTORY SYSTEMS HOW TO GET THERE: The following section explains how to access and operate the factory systems that have been retained. Your vehicle must already be equipped with these systems. FACTORY SYSTEMS The Maestro Rr module retains your factory system functionalities with your new Kenwood radio. In order for them to be functional, these features must be retained during the Maestro Rr online programming with the Weblink Updater.
USING YOUR FACTORY SYSTEMS USING YOUR FACTORY SYSTEMS (Continued) HOW TO GET THERE: Automotive Data Solutions Inc. © 2014 SYNC BLUETOOTH To stream audio via Bluetooth, enter the Sync Bluetooth source. From here, you can either stream music that is stored on the paired device or audio from another application, such as Pandora. SYNC MEDIA The Sync Media source will allow you to use the line in and USB.
USING MAESTRO FEATURES USING MAESTRO FEATURES Maestro features can be accessed in the My Car submenu. If an icon is not active (grayed out) then it is not available in your vehicle or it was disabled when the Maestro module was programmed using Weblink. The options described here may not be available in your vehicle. GAUGES HOW TO GET THERE: Press on Gauges to view the gauges that are selected. During the installation, the default gauge choices will be displayed.
USING MAESTRO FEATURES USING MAESTRO FEATURES (Continued) HOW TO GET THERE: VEHICLE INFO The Vehicle Info screen displays information about the vehicle such as battery voltage and open entry points. If the Check Engine light is ON in the vehicle, the CHECK ENGINE button will become active. Press this button to see the active trouble codes and attempt to reset them. Press Settings to configure the alerts that can be generated.
CHANGING THE SETTINGS CHANGING THE SETTINGS HOW TO GET THERE: VEHICLE INFO SETTINGS These settings can be accessed as shown here or by pressing the Settings button on the Vehicle Info screen. Tire Alert Enables the vehicle info screen to be displayed automatically when a TPMS fault is detected (only if TPMS is available in the vehicle). Check Engine Alert Enables the Vehicle Info screen to be displayed automatically when the check engine light turns ON in the vehicle.
CHANGING THE SETTINGS CHANGING THE SETTINGS (Continued) HOW TO GET THERE: GAUGES SETTINGS These settings can be accessed as shown here or by pressing the Settings button on the Gauges screen. Select Gauges Used to assign gauges to the gauges screen. See the Gauges section of this guide for more details. Gauges Global Units Changes the units of all gauges to Metric or English system. However, the units of each gauge can be set individually in the settings option for that gauge.
CHANGING THE SETTINGS CHANGING THE SETTINGS (Continued) HOW TO GET THERE: Climate Settings Climate settings can be accessed as shown here or by pressing Settings button on the Climate screen. Climate Type Gives the choice of Manual, Auto, or Dual Zone Auto. the controls should be set to manual, not auto, as auto climate controls are not present in the Mustang. Heated Seats Turns ON or OFF the option to show and control heated seats from the climate screen.
