Owner manual

ManualsBrandsMag Layers USA ManualsHardwareMCI-2012

SCOPE

：

This specification applies to the Pb Free Common mode filters

for MCI-2012-SERIES-□□

PRODUCT INDENTIFICATION

MCI- 2012 - 900 -□□

① ② ③ ④

① Product Code

② Dimensions Code

③ Impedance Code

(1) SHAPES AND DIMENSIONS

A: 2.0±0.20 mm

B: 1.2±0.20 mm

C: 0.17 Typ. mm

D: 1.2±0.20 mm

E: 0.45 Typ. mm

F: 0.40 Typ. mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

TEST INSTRUMENTS

Z : HP 4291B IMPEDANCE ANALYZER (or equivalent)

RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

I.R : CHROMA MODEL 19073 AC/DC/IR HIPOT TESTER (or equivalent)

(3) CHARACTERISTICS

(3)-1 Temperature rise ...................... ＋20℃ Max.

(3)-2 Ambient temperature ................ ＋60℃ Max.

(3)-3 Operate temperature range …... －25℃～＋85℃

(Including self temp. rise)

(3)-4 Storage temperature range ...... －40℃～＋85℃

MCI-2012-SERIES Page 1/7

④ Inner Control Code

MAG.LAYERS

Summary of content (9 pages)

PAGE 1
SCOPE： This specification applies to the Pb Free Common mode filters for MCI-2012-SERIES-□□ PRODUCT INDENTIFICATION MCI- 2012 - 900 -□□ ① ② ③ ④ ① Product Code ② Dimensions Code ③ Impedance Code ④ Inner Control Code (1) SHAPES AND DIMENSIONS A: 2.0±0.20 mm B: 1.2±0.20 mm C: 0.17 Typ. mm D: 1.2±0.20 mm E: 0.45 Typ. mm F: 0.40 Typ.
PAGE 2
TABLE 1 PT/NO. Impedance Z(Ω) @ 100MHz/0.5V RDC (Ω) Max. Rated Voltage Vdc(V) Idc Max.(mA) Withstanding Voltage Vdc(V) Insulation Resistance (MΩ)Min. MCI-2012-670 67 ±25% 0.25 50 400 125 10 MCI-2012-900 90 ±25% 0.35 50 330 125 10 MCI-2012-121 120±25% 0.30 50 370 125 10 MCI-2012-181 180±25% 0.35 50 330 125 10 MCI-2012-201 200±25% 0.35 50 330 125 10 MCI-2012-261 260±25% 0.40 50 300 125 10 MCI-2012-371 370±25% 0.
PAGE 3
(4) RELIABILITY TEST METHOD Specifications Item Solder ability Test conditions It can be connected on the Apply cream solder to the test circuit board . Recommendation soldering condition. It is mounted on the recommendation soldering condition. Dip pads in flux and dip in solder pot ( 96.5 Sn/3.5 Ag solder) at 260°C ±5°C. Terminal The terminal electrode and the ferrite Solder a chip to test substrate , and then laterally strength must not be damaged. apply a load 0.5Kg in the arrow direction.
PAGE 4
Item Specifications Test conditions Temperature : +85±2℃ Applied voltage : Rated voltage High temperature Applied current : Rated current Testing time : 500±12 hours Measurement :After placing for 24 hours min. Temperature : +85±2℃ Humidity : 90 to 95%RH Applied current : Rated current Humidity resistance Applied voltage : Rated voltage Testing time : 500±12 hours Measurement :After placing for 24 hours min. Appearance : Ferrite shall not be damaged. Impedance:Within±20% of the initial value.
PAGE 5
(5) RECOMMENDED SOLDERING CONDITIONS (Please use this product by reflow soldering) (5)-1 RECOMMENDED FOOTPRINT Unit: mm (5)-2 RECOMMENED REFLOW PATTERN T e m p e r a tu r e ( ℃ ) S o ld in g 260℃ 300 260 200 P r e h e a ti n g N a tu r a l C o o lin g 150 100 50 T im e 1 t o 4 m in . 10 sec m o r e th a n 2 m in . (5)-3 IRON SOLDERING Use a solder iron of less than 30W when soldering ,do not allow the soldering iron tip directly touch the Ceramic body outside of terminal electrode. 3 seconds max.
PAGE 6
(6) PACKAGING (6)-1 CARRIER TAPE DIMENSIONS (mm) P P1 P0 W W : 8.0 mm P : 4.0 mm P0 : 4.0 mm P1 : 2.0 mm (6)-2 TAPING DIMENSIONS (mm) There shall not continuation more than two vacancies of the product. (360 mm) Leader. Blank (50 pitches) Chip Blank (70 pitches) (6)-3 REEL DIMENSIONS D C B A A : 180 mm B : 60 mm C : 13 mm D : 12 mm E : 8.4 mm E MAG.
PAGE 7
(6)-4 COVER TAPE PEEL STRENGTH The force for tearing off cover tape is 0.1~0.6(N) in the arrow direction at the following conditions: Temperature : 5 ~ 35℃ Humidity : 45 ~ 85% Atmospheric pressure : 860 ~ 1060 hpa 160 ~ 180。 Top cover tape Base tape (6)-5 QUANTITY 2000 pcs/Reel (6)-6 The products are packaged so that no damage will be sustained.
PAGE 8
TYPICAL ELECTRICAL CHARACTERISTICS MCI-2012-900 MCI-2012-670 1000 10000 Common Mode Common mode Differential Mode Differential mode 1000 Impedance(Ω) Impedance(Ω) 100 10 100 10 1 1 0.1 0.1 1 10 100 1 1000 10 Frequency(MHz) 100 1000 Frequency(MHz) MCI-2012-181 MCI-2012-121 10000 1000 Common Mode Common Mode Differential Mode Differential Mode 1000 Impedance(Ω) Impedance(Ω) 100 10 1 100 10 1 0.1 0.
PAGE 9
TYPICAL ELECTRICAL CHARACTERISTICS MCI-2012-201 1000 MCI-2012-261 10000 Common Mode Common Mode Differential Mode Differential 1000 Impedance(Ω) Impedance(Ω) 100 100 10 10 1 0.1 1 1 10 100 Frequency(MHz) 1000 1 10 100 1000 Frequency(MHz) MIC-2012-371 10000 Common Mode Differential Mode Impedance(Ω) 1000 100 10 1 0.1 1 10 100 1000 Frequency(MHz) MAG.