Manual

ManualsBrandsMag Layers USA ManualsHardwareMCM-7060M

Ⅰ

. SCOPE

：

This specification applies to the Pb Free high current type SMD Common mode filter

for MCM-7060M-SERIES

PRODUCT INDENTIFICATION

MCM-7060M- 301

① ② ③

① Product Code

② Dimensions Code

③ Impedance Code

(1) SHAPES AND DIMENSIONS

A: 7.0±0.5 mm

B: 6.0±0.5 mm

C: 3.8Max. mm

D: 3.5Typ. mm

E: 1.5±0.2 mm

F: 1.5±0.2 mm

G: 1.75±0.2 mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

TEST INSTRUMENTS

Z : HP 4291B IMPEDANCE ANALYZER (or equivalent)

RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3) CHARACTERISTICS

(3)-1 Temperature rise …................... ＋40℃ Max.

(3)-2 Operate temperature range ...... －40℃～＋125℃

(Including self temp. rise)

(3)-3 Storage temperature range ...... －40℃～＋125℃

MCM-7060M-SERIES

Page 1/8

MAG.LAYERS

Summary of content (8 pages)

PAGE 1
Ⅰ. SCOPE： This specification applies to the Pb Free high current type SMD Common mode filter for MCM-7060M-SERIES PRODUCT INDENTIFICATION MCM-7060M- 301 ① ② ③ ① Product Code ② Dimensions Code ③ Impedance Code (1) SHAPES AND DIMENSIONS A: 7.0±0.5 mm B: 6.0±0.5 mm C: 3.8Max. mm D: 3.5Typ. mm E: 1.5±0.2 mm F: 1.5±0.2 mm G: 1.75±0.
PAGE 2
TABLE 1 Impedance(Ω) MAGLAYERS PT/NO. Resistance RDC(Ω) Max.(1 line) at 100MHz Rated Insulation Current Resistance (A) Max. (MΩ) Min. Rated Voltage (V)Max. Min. Typ. MCM-7060M-101 100 140 10m 9 10 80 MCM-7060M-301 225 300 10m 5 10 80 MCM-7060M-501 275 350 10m 5 10 80 MCM-7060M-601 500 700 15m 4 10 80 MCM-7060M-701 500 700 15m 4 10 80 MCM-7060M-102 800 1020 17m 3 10 80 MCM-7060M-132 910 1300 21m 2.
PAGE 3
(4) RELIABILITY TEST METHOD MECHANICAL TEST ITEM Resistance to TEST DETAILS The product shall be connected to the test Apply cream solder to the printed circuit board . circuit board by the fillet (the height is 0.2mm). Refer to clause 8 for Reflow profile. There shall be no damage or problems.
PAGE 4
(4) RELIABILITY TEST METHOD MECHANICAL TEST ITEM SPECIFICATION TEST DETAILS Humidity Impedance:Within±20% of the initial value. After the samples shall be soldered onto the test circuit resistance Insulation resistance and DC resistance on the board,the test shall be done. specification(refer to clause 2-1) shall be met. Measurement : After placing for 24 hours min. The terminal electrode and the ferrite must not Temperature : +60±2℃ , Humidity : 90 to 95 %RH damaged.
PAGE 5
(5) LAND DIMENSION (Ref.) PCB: GLASS EPOXY t＝1.6mm (5)-1 LAND PATTERN DIMENSIONS (STANDARD PATTERN) Unit:mm (6) TEST EQUIPMENT (6)-1 Impedance Measured by using HP4291B RF Impedance Analyzer. Measurement terminal ① ④ ② ③ (6)-2 DC Resistance Measured by using Chroma 16502 milliohm meter. Measurement terminal ① ④ ② ③ (6)-3 Insulation Resistance Measured by using Chroma 19073 Measurement voltage : 50v ,Measurement time : 60 sec. Measurement terminal ① ④ ② ③ MAG.
PAGE 6
(6) PACKAGING (6)-1 CARRIER TAPE DIMENSIONS (mm) (6)-2 TAPING DIMENSIONS (mm) Unreeling Direction MAG.
PAGE 7
(6)-3 REEL DIMENSIONS (mm) (6)-4 QUANTITY 1500 pcs/Reel The products are packaged so that no damage will be sustained. MAG.
PAGE 8
TYPICAL ELECTRICAL CHARACTERISTICS CHARACTERISTICS(REFERENCE) MCM-7060M-132 10000 Common mode Impedance(Ω) 1000 Differential mode 100 10 1 1 10 100 1000 Frequency(MHz) M A G .