Owner's manual

ManualsBrandsMag Layers USA ManualsHardwareMSCD-43

SCOPE

：

This specification applies to the Pb Free high current type SMD inductors for

MSCD-43-SERIES

PRODUCT INDENTIFICATION

MSCD- 43 - 100 K

① ② ③ ④

① Product Code

② Dimensions Code

③ Inductance Code

④ Tolerance Code

(1) SHAPES AND DIMENSIONS

A: 4.5 ± 0.3 mm

B: 4.0 ± 0.3 mm

C: 3.2 ± 0.3 mm

D: 1.5 Typ. mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

TEST INSTRUMENTS

L : HP 4284A PRECISION LCR METER (or equivalent)

RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3) CHARACTERISTICS

(3)-1 Ambient temperature ……......... ＋60℃ Max.

(3)-2 Operate temperature range ...... －40℃～＋125℃

(Including self temp. rise)

(3)-3 Storage temperature range ...... －40℃～＋125℃

Page 1/8

MSCD-43-SERIES

MAG.LAYERS

Summary of content (8 pages)

PAGE 1
SCOPE： This specification applies to the Pb Free high current type SMD inductors for MSCD-43-SERIES PRODUCT INDENTIFICATION MSCD- 43 - 100 K ① ② ③④ ① Product Code ② Dimensions Code ③ Inductance Code ④ Tolerance Code (1) SHAPES AND DIMENSIONS A: 4.5 ± 0.3 mm B: 4.0 ± 0.3 mm C: 3.2 ± 0.3 mm D: 1.5 Typ.
PAGE 2
TABLE 1 MAGLAYERS Inductance Resistance Rated DC Current Frequency RDC(Ω)Max. IDC(A) M 100kHz/0.25V 48.7m M 100kHz/0.25V Percent PT/NO. L(μH) Tolerance MSCD-43-1R0□ 1.0 MSCD-43-1R2□ 1.2 Test Marking Wire Tuns(Ref.) 2.70 1R0 _ 52.4m 2.60 1R2 _ MSCD-43-1R4□ 1.4 M 100kHz/0.25V 56.2m 2.50 1R4 _ MSCD-43-1R5□ 1.5 M 100kHz/0.25V 56.2m 2.50 1R5 _ MSCD-43-1R8□ 1.8 M 100kHz/0.25V 63.7m 2.33 1R8 _ MSCD-43-2R2□ 2.2 K,M 100kHz/0.25V 71.2m 2.
PAGE 3
(4) RELIABILITY TEST METHOD MECHANICAL TEST ITEM Substrate bending SPECIFICATION △L/Lo≦±5% TEST DETAILS The sample shall be soldered onto the printed circuit board in figure 1 and a load applied unitil the figure in the arrow There shall be direction is made approximately 3mm.(keep time 30 seconds) no mechanical PCB dimension shall the page 7/9 damage or elec- F(Pressurization) trical damege.
PAGE 4
MECHANICAL TEST ITEM SPECIFICATION There shall be Soldering heat no damage or (reflow soldering) problems. Temperature profile of reflow soldering Sodering temperature (℃) Resistance to soldering (Peak temperature 260±3℃ 10 sec 300 250 200 30 sec Min 150 Pre-heating 100 150 ~ 180℃ (230+0 ℃) Slow cooling (Stored at room temperature) 50 2 min 10 sec. 2 min. or more The specimen shall be passed through the reflow oven with the condition shown in the above profile for 1 time.
PAGE 5
ENVIROMENT CHARACTERISTICS TEST ITEM High temperature SPECIFICATION △L/Lo≦±5% storage The sample shall be left for 96±4 hours in an atmospere with a temperature of 85±2℃ and a normal humidity. Low temperature There shall be Upon completion of the measurement shall be made after the no mechanical sample has been left in a normal temperature and normal damage. humidity for 1 hour. △L/Lo≦±5% The sample shall be left for 96±4 hours in an atmosphere with storage a temperature of -25±3℃.
PAGE 6
(5) LAND DIMENSION (Ref.) PCB: GLASS EPOXY t＝1.6mm (5)-1 LAND PATTERN DIMENSIONS (STANDARD PATTERN) Unit:mm 4.50 Land 1.75 5.0 1.50 R1.0 Part of silk screen (5)-2 SUBSTRATE BENDING TEST BENDING TEST BOARD MAG.
PAGE 7
(6) PACKAGING 12 (6)-1 CARRIER TAPE DIMENSIONS (mm) (6)-2 TAPING DIMENSIONS (mm) Unreeling Direction MAG.
PAGE 8
(6)-3 REEL DIMENSIONS (mm) Tape width:12 (6)-4 QUANTITY 1500 pcs/Reel The products are packaged so that no damage will be sustained. MAG.