User guide

ManualsBrandsMag Layers USA ManualsHardwareMSCDRI-105B

SCOPE

：

This specification applies to the Pb Free high current type SMD inductors for

MSCDRI-105B-SERIES

PRODUCT INDENTIFICATION

MSCDRI-105B-100 M

① ② ③ ④

① Product Code

② Dimensions Code

③ Inductance Code

④ Tolerance Code

(1) SHAPES AND DIMENSIONS

A: 10.0± 0.4 mm

B: 9.00± 0.4 mm

C: 5.20± 0.5 mm

D: 3.50 Typ. mm

E: 3.00 Typ. mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

TEST INSTRUMENTS

L : HP 4284A PRECISION LCR METER (or equivalent)

RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3) CHARACTERISTICS

(3)-1 Ambient temperature ……......... ＋60℃ Max.

(3)-2 Operate temperature range ...... －40℃～＋125℃

(Including self temp. rise)

(3)-3 Storage temperature range ...... －40℃～＋125℃

Page 1/8

MSCDRI-105B-SERIES

MAG.LAYERS

Summary of content (8 pages)

PAGE 1
SCOPE： This specification applies to the Pb Free high current type SMD inductors for MSCDRI-105B-SERIES PRODUCT INDENTIFICATION MSCDRI-105B-100 M ① ② ③ ④ ① Product Code ② Dimensions Code ③ Inductance Code ④ Tolerance Code (1) SHAPES AND DIMENSIONS A C B A: 10.0± 0.4 mm B: 9.00± 0.4 mm C: 5.20± 0.5 mm D: 3.50 Typ. mm E: 3.00 Typ.
PAGE 2
TABLE 1 MAGLAYERS Inductance Percent Test Resistance Rated DC Current PT/NO. L(μH) Tolerance Frequency RDC(Ω) Max. IDC(A) MSCDRI-105B-100□ 10 M,N 100kHz/0.25V 60m 2.06 100 MSCDRI-105B-120□ 12 M,N 100kHz/0.25V 70m 1.94 120 MSCDRI-105B-150□ 15 M,N 100kHz/0.25V 70m 1.72 150 MSCDRI-105B-180□ 18 M,N 100kHz/0.25V 80m 1.58 180 MSCDRI-105B-220□ 22 M,N 100kHz/0.25V 80m 1.42 220 MSCDRI-105B-270□ 27 M,N 100kHz/0.25V 0.10 1.
PAGE 3
(4) RELIABILITY TEST METHOD MECHANICAL TEST ITEM Substrate bending SPECIFICATION △L/Lo≦±5% TEST DETAILS The sample shall be soldered onto the printed circuit board in figure 1 and a load applied unitil the figure in the arrow There shall be direction is made approximately 3mm.(keep time 30 seconds) no mechanical PCB dimension shall the page 7/9 damage or elec- F(Pressurization) trical damege.
PAGE 4
MECHANICAL TEST ITEM SPECIFICATION There shall be Soldering heat no damage or (reflow soldering) problems. Temperature profile of reflow soldering Sodering temperature (℃) Resistance to soldering (Peak temperature 260±3℃ 10 sec 300 250 200 150 100 30 sec Min Pre-heating (230+0 ℃) Slow cooling (Stored at room temperature) 150 ~ 180℃ 50 2 min 10 sec. 2 min. or more The specimen shall be passed through the reflow oven with the condition shown in the above profile for 1 time.
PAGE 5
ENVIROMENT CHARACTERISTICS TEST ITEM High temperature SPECIFICATION △L/Lo≦±5% storage The sample shall be left for 96±4 hours in an atmospere with a temperature of 85±2℃ and a normal humidity. Low temperature There shall be Upon completion of the measurement shall be made after the no mechanical sample has been left in a normal temperature and normal damage. humidity for 1 hour. △L/Lo≦±5% The sample shall be left for 96±4 hours in an atmosphere with storage a temperature of -25±3℃.
PAGE 6
(5) LAND DIMENSION (Ref.) PCB: GLASS EPOXY t＝1.6mm (5)-1 LAND PATTERN DIMENSIONS (STANDARD PATTERN) 9.50 2.5 10.0 3.75 Land R1.0 Part of silk screen (5)-2 SUBSTRATE BENDING TEST BENDING TEST BOARD MAG.
PAGE 7
(6) PACKAGING (6)-1 CARRIER TAPE DIMENSIONS (mm) (6)-2 TAPING DIMENSIONS (mm) Unreeling Direction MAG.
PAGE 8
(6)-3 REEL DIMENSIONS (mm) (6)-4 QUANTITY 500pcs/Reel The products are packaged so that no damage will be sustained. MAG.