Owner manual

ManualsBrandsMag Layers USA ManualsHardwareMSCH-3225C

SCOPE

：

This specification applies to the Pb Free high current type SMD inductors for

MSCH-3225C-SERIES

PRODUCT INDENTIFICATION

MSCH - 3225C - 100 K

① ② ③ ④

① Product Code

② Dimensions Code

③ Inductance Code

④ Tolerance Code

(1) SHAPES AND DIMENSIONS

A: 3.2±0.3 mm

B: 2.5±0.2 mm

C: 2.0±0.3 mm

D: 1.0Typ. mm

E: 1.2Typ. mm

(2) ELECTRICAL SPECIFICATIONS

SEE TABLE 1

TEST INSTRUMENTS

L : HP 4284A PRECISION LCR METER (or equivalent)

HP 4285A PRECISION LCR METER (or equivalent)

SRF : HP 4291B IMPEDANCE ANALYZER (or equivalent)

RDC : CHROMA MODEL 16502 MILLIOHMMETER (or equivalent)

(3) CHARACTERISTICS

(3)-1 Ambient temperature ……......... ＋60℃ Max.

(3)-2 Operate temperature range ...... －40℃～＋125℃

(Including self temp. rise)

(3)-3 Storage temperature range ...... －40℃～＋125℃

MSCH-3225C-SERIES Page 1/8

MAG.LAYERS

Summary of content (8 pages)

PAGE 1
SCOPE： This specification applies to the Pb Free high current type SMD inductors for MSCH-3225C-SERIES PRODUCT INDENTIFICATION MSCH - 3225C - 100 K ① ② ③ ④ ① Product Code ② Dimensions Code ③ Inductance Code ④ Tolerance Code (1) SHAPES AND DIMENSIONS A: 3.2±0.3 mm B: 2.5±0.2 mm C: 2.0±0.3 mm D: 1.0Typ. mm E: 1.2Typ.
PAGE 2
TABLE 1 MAGLAYERS Inductance Percent Test Resistance IDC PT/NO. L(μH) Tolerance Frequency RDC(Ω)Max. (mA) Max. MSCH-3225C-R50□ 0.5 M,N 1MHz/0.25V 60m 1000 150 MSCH-3225C-1R0□ 1.0 M,N 1MHz/0.25V 78m 800 96 MSCH-3225C-2R2□ 2.2 M,N 1MHz/0.25V 0.1261 600 64 MSCH-3225C-2R7□ 2.7 M,N 1MHz/0.25V 0.150 550 60 MSCH-3225C-3R3□ 3.3 K,M,N 1MHz/0.25V 0.160 500 54 MSCH-3225C-4R7□ 4.7 M,N 1MHz/0.25V 0.195 450 43 MSCH-3225C-6R8□ 6.8 M,N 1MHz/0.25V 0.
PAGE 3
(4) RELIABILITY TEST METHOD MECHANICAL TEST ITEM Substrate bending SPECIFICATION △L/Lo≦±5% TEST DETAILS The sample shall be soldered onto the printed circuit board in figure 1 and a load applied unitil the figure in the arrow There shall be direction is made approximately 3mm.(keep time 30 seconds) no mechanical PCB dimension shall the page 7/9 damage or elec- F(Pressurization) trical damege.
PAGE 4
MECHANICAL TEST ITEM SPECIFICATION There shall be Soldering heat no damage or (reflow soldering) problems. Temperature profile of reflow soldering Sodering temperature (℃) Resistance to soldering (Peak temperature 260±3℃ 10 sec 300 250 200 150 30 sec Min Pre-heating 100 (230+0 ℃) Slow cooling (Stored at room temperature) 150 ~ 180℃ 50 2 min 10 sec. 2 min. or more The specimen shall be passed through the reflow oven with the condition shown in the above profile for 1 time.
PAGE 5
ENVIROMENT CHARACTERISTICS TEST ITEM High temperature SPECIFICATION △L/Lo≦±5% storage The sample shall be left for 96±4 hours in an atmospere with a temperature of 85±2℃ and a normal humidity. Low temperature There shall be Upon completion of the measurement shall be made after the no mechanical sample has been left in a normal temperature and normal damage. humidity for 1 hour. △L/Lo≦±5% The sample shall be left for 96±4 hours in an atmosphere with storage a temperature of -25±3℃.
PAGE 6
(5) LAND DIMENSION (Ref.) PCB: GLASS EPOXY t＝1.6mm (5)-1 LAND PATTERN DIMENSIONS (STANDARD PATTERN) Unit:mm (5)-2 SUBSTRATE BENDING TEST BENDING TEST BOARD MAG.
PAGE 7
(6) PACKAGING 8 (6)-1 CARRIER TAPE DIMENSIONS (mm) (6)-2 TAPING DIMENSIONS (mm) Unreeling Direction MAG.
PAGE 8
(6)-3 REEL DIMENSIONS (mm) (6)-4 QUANTITY 2000pcs/Reel The products are packaged so that no damage will be sustained. MAG.