All-In-One Wireless Security System V1.
Table of Contents Introduction................................................... 3 About Magellan and this Manual............................. 3 Conventions ............................................................ 3 Specifications.......................................................... 3 Quick Setup................................................... 4 Installation..................................................... 6 AC Power................................................................
WinLoad Software Settings ....................... 34 Panel Answer Options ........................................... 34 Panel Identifier....................................................... 34 PC Password ......................................................... 34 PC Telephone Number .......................................... 34 Call Back Feature .................................................. 34 Appendix 1: Automatic Report Code List.. 35 Appendix 2: Ademco Contact ID Report Code List .............
Introduction About Magellan and this Manual Specifications Magellan is designed for fast and easy installation. Simply remove it from the box, mount the console and wireless transmitters, apply power, perform some basic programming and Magellan is ready to protect your home. Power input: Some of Magellan’s features can be programmed through a quick Installer menu (menu programming) or through section programming.
Quick Setup Follow these steps to quickly set up Magellan with the required settings for a basic security installation. to immediately access the “Zone Profile” menu. For more in-depth programming of the console’s communication features, see Reporting and Dialer Settings on page 25. 1.Getting Started 1. After powering up for the first time, press [START] to access the Installer menu. 2. The first menu option will appear. Press [NEXT] to go to the “User Profile” menu. 2.User Programming 1.
When you are done the next menu option will appear. Press [NEXT] until you see the “Passwords” menu or press the [8] key to immediately access the “Passwords” menu. Deleting Zones 1. From the “Zone Profile” menu, press [OK]. 6.Passwords 1. From the “Passwords” menu, press [OK]. 2. Select which password(s) or code(s) you wish to program by pressing [NEXT] and press [OK] when the desired password appears.
Installation Figure 2: Connecting the Backup Battery (cont’d) AC Power Magellan requires a 9Vac (1A) or 16.5Vac (1A) transformer (not included) to supply power to the console. Connect the transformer to the AC terminals as shown in Figure 1 on page 6. 2. Slide in the battery pack horizontally, tilt the battery pack downward and then tuck it in Magellan’s battery compartment. Magellan can also be powered through a DC power supply.
For UL compliant installations, the Magellan console must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephones, answering machines, computer modems, etc.) already has the line in use. To do so, the Magellan console must be connected to a properly installed RJ31X jack that is in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the diagram below.
Figure 7: On-site Connection Hardwire Zone Connections Back view of the Magellan console. Magellan comes with two on-board hardwire zones. You can connect hardwire detection devices such as door contacts to Magellan’s zone terminals. Connect the detection devices as shown in Figure 6 on page 8. Please note the following: • Section [095] options [1] and [2] must be enabled in order to use the two on-board hardwire zones. See Zones 15 and 16 Become Hardwire Zones on page 16 for more information.
X10 Transmitter Connection Location and Mounting Magellan supports the X10 communication protocol. X10 is a communication protocol for remote control of electrical devices such as lamps and appliances. Communication is accomplished through standard household electrical wiring using X10 transmitters and receivers. Configure Magellan, with the use of an X10 transmitter, to automate a home. Connect the X10 transmitter as shown in Figure 9 on page 9. Refer to the Magellan X10 Instructions on our website, www.
Figure 12: Mounting Magellan onto the Wall Plate rubber stops prevent the console from sliding when Magellan is being used. To do so: 1. Place the console back plate flush against the wall plate. 2. Slide the Magellan’s open slots labeled D (see Figure 13 on page 10) onto the wall plate’s tabs labeled B (see Figure 12 on page 10). 3. Gently apply downward pressure to insert the wall plate’s tabs into Magellan’s open slots. 4.
Programming Methods WinLoad Installer Upload/Download Software Program the Magellan console remotely or on-site using the WinLoad Installer Upload/Download Software for Windows®. For more information, contact your local Paradox Distributor or visit our Web site at www.paradox.ca. If you are using the WinLoad software, you must program the features explained on page 34. Please refer to WinLoad’s Online Help for more information on using WinLoad.
User Codes A person must be assigned to a User code in order to have access to Magellan. A User code defines the extent of a user’s access to the system and consists of a code # (PIN) and user options. Magellan supports one Installer code, one Maintenance code and up to 16 User codes (one System Master code and 15 User codes). Installer Code Used to program all console settings except User codes and remote controls.
Zone Programming Magellan supports up to 16 wireless zones whereby each zone can be configured with a different zone definition and option. Each zone can also have a voice label recorded for it. Magellan’s zones can be programmed using section programming or through the Installer menu. See Quick Setup on page 4 for more information on zone programming using the Installer menu.
Follow/Stay Zones Figure 18: Delayed Fire Zone Sections [001] to [016]: Zones 1 to 16, 3-digit # = 004 Follow/Stay zones function as follows: • • All zones defined as Follow/Stay zones become Follow zones (refer to Follow Zones on page 13) when the Magellan system is Regular armed. All zones defined as Follow/Stay zones become Stay zones when the Magellan system is Stay or Instant armed.
24Hr. Gas Zones Bypass Option Sections [001] to [016]: Zones 1 to 16, 3-digit # = 012 Section [001] to [016]: Zones 1 to 16; Option [2] When a 24Hr. Gas zone opens, whether it is armed or disarmed, the console will immediately generate an alarm. The SIA FSK reporting format includes specific report codes to identify the alarm as a Gas alarm (see Appendix 1: Automatic Report Code List on page 35). Option [2] OFF = Bypass option disabled Option [2] ON = Selected zone is Bypass enabled (default) 24Hr.
• • • During the Intellizone Delay, a second zone has caused an alarm. During the Intellizone Delay, the zone in alarm has restored (closed) and re-occurred (opened). The zone in alarm is still open after the Intellizone Delay has elapsed. Intellizone Delay Timer Section [065]: 010 to 255 seconds; Default = 48 seconds Enter the desired 3-digit value into section [065] to program the Intellizone Delay Timer.
Wireless Programming The Magellan system supports up to 16 wireless zones and two wireless doorbells. These wireless zones are monitored using transmitters such as wireless detectors and door contacts. The Magellan console only supports the Paradox Magellan series of wireless transmitters. The programming of the transmitters is accomplished in two steps: 1. Assign the wireless transmitter to Magellan. 2. Program the wireless zone. Assigning Wireless Zone Transmitters 3.
• “Weak”: This is the weakest reading. The transmitter should be moved to another location. Sometimes moving the transmitter by a small amount will greatly increase the signal reception. Programming the Remote Control’s Buttons Sections [161] to [176]: Users 1 to 16; Remote Controls 1 to 16 Sections [161] to [176] represent the remote controls assigned to User codes 1 to 16 (see Table 4 on page 18). To view the signal strength of a wireless transmitter: 1.
Section RC# [172] 12 Data (Default: 4DE0) ______ MG-REM1 Remote Control Buttons User # ______ ______ ______ 012 + [173] 13 ______ ______ ______ ______ 013 + [174] 14 ______ ______ ______ ______ 014 + [175] 15 ______ ______ ______ ______ 015 + [176] 16 ______ ______ ______ ______ 016 + MG-REM1 Table 5: MG-REM2 Remote Control Button Programming Section RC# [161] 1 Data (Default: 4DE0) ______ User # ______ ______ ______ MG-REM2 Remote Control Buttons 001
Figure 19: Remote Control Button Options Hex Value Description Hex Value Description 0 Button disabled 8 Panic 1† 1 Regular arming 9 Panic 2† 2 Stay arming A* Panic 3† 3 Instant arming B* PGM Activation (Event Group #07 - Refer to the Magellan Programming Guide) 4 Force arming C* PGM Activation (Event Group #08 - Refer to the Magellan Programming Guide) 5 Future use D* Turn FM radio ON/OFF 6 Future use E* FM radio memory scan 7 Future use F* Paramedic alarm * = Hex values
Arming and Disarming Regular Arming Switches to Stay Arming Section [092]: Option [4] Option [4] OFF = Regular arming switches to Stay arming disabled (default) Option [4] ON = Regular arming switches to Stay arming enabled If a user Regular arms the system, but does not exit through (open and close) an Entry Delay zone during the Exit Delay, the console can be programmed to switch from Regular arming to Stay arming.
One-Touch Arming Follow Zone Switches to Entry Delay 2 Section [092]: Options [7] and [8] Option [7] OFF = One-touch Regular/Force arming disabled Option [7] ON = One-touch Regular/Force arming enabled (default) Section [093]: Option [7] Option [7] OFF = Follow zone triggers an alarm (default) Option [7] ON = Follow zone follows Entry Delay 2 when opened Option [8] OFF = One-touch Stay arming disabled Option [8] ON = One-touch Stay arming enabled (default) When option [7] is enabled (ON) and an Entry D
Alarm Options Bell Cut-off Timer Check-in Supervision Options Section [063]: 001 to 255 minutes; 000 = Disabled; Default = 4 minutes Section [103]: Options [1] to [8]; Zones 1 to 8; Default: All ON Section [104]: Options [1] to [8]; Zones 9 to 16; Default: All ON After an audible alarm, the siren will stop upon the disarming of the system or when the Bell Cut-Off timer has elapsed, whichever comes first.
Table 8: Panic Alarm Keys Table 7: Tamper Recognition Options Options [3] [4] OFF OFF OFF ON ON OFF Description ON Panic Alarm Type [1] and [3] Panic 1 (Emergency Panic) Tamper Recognition disabled (default) [4] and [6] Panic 2 (Auxiliary Panic) Trouble only System armed or disarmed: If a tamper wiring failure occurs on a zone, the console will generate a trouble and send a report to the monitoring station (if programmed).
Reporting and Dialer Settings Report Codes A report code is a 1- or 2-digit hexadecimal value consisting of digits from 1 to F. Each section from [120] to [156] represents a set of up to four specific events and each of these events can be programmed with a separate 1- or 2-digit report code. Only the Ademco Slow, Silent Knight, and Sescoa formats support 1-digit report codes. To program a 1-digit report code, press the [0] key followed by the desired hexadecimal digit or vice versa.
• • Fire Panic: Panic keys [7] and [9] (see page 24) or the appropriate button(s) on a remote control (see page 18) have been pressed. Recent Closing: Reports when an alarm is generated after arming the system within the period defined by the Recent Close Delay (see page 30). • Tx Supervision Loss: Check-in Supervision (see page 23) has been enabled and a transmitter is no longer communicating with the system.
Monitoring Station Telephone Numbers (MSTNs) • Section [111] = Monitoring Station Telephone Number 1 Section [112] = Monitoring Station Telephone Number 2 The Magellan console uses the MSTNs (Monitoring Station Telephone Numbers) programmed in sections [111] and/or [112] to connect and communicate with the monitoring station.
4. Press [NEXT] until the desired telephone number appears, then press [OK]. 5. Enter the desired telephone number and then press [OK] twice. 6. Press [NEXT] until the desired report type appears, then press [OK] (see Report Types on page 28). 7. Press [NEXT] until the Record Alrm Mes? screen appears, then press [OK]. 8. Record the alarm message. Report Types There are four report types that can be used with Utility Reporting.
Section [102]: Options [1] to [3]; Special Option [1] ON = Call MSTN 1 Option [2] ON = Call MSTN 2 Option [3] ON = Call Pager telephone number The events are divided into five groups (see above) where each event group can be programmed to dial up to three telephone numbers (MSTN 1 & 2 and the Pager telephone number) with one as a possible backup (see MSTN 2 as Backup Number on page 27).
Table 11: Telephone Line Monitoring Options Options Description [1] [2] OFF OFF TLM disabled (default) OFF ON Trouble only: Upon a line test failure, a TLM trouble will appear in the console’s Trouble Display. ON OFF Alarm if System Armed: Upon a line test failure, a TLM trouble will appear in the console’s Trouble Display and if the system is armed, the console will generate an alarm.
Programmable Outputs A PGM is a programmable output that toggles to its opposite state (i.e. a normally open PGM will close) when a specific event has occurred in the system. For example, a PGM can be used to activate bells or strobe lights, open/close garage doors and much more. When a PGM activates, the control panel triggers any device or relay connected to it. here has elapsed. Enter 000 to have the PGMs deactivate with a PGM Deactivation Event (see page 31).
System Settings Software Reset Daylight Savings Time Section [201] Section [096]: Option [5] Option [5] OFF = Daylight Savings Time disabled (default) Option [5] ON = Daylight Savings Time enabled Performing a software reset will reset all programmed sections back to the factory defaults. To perform a software reset: 1. 2. Access the installer programming mode (see page 11). Enter section [201].
Trouble Description Supervision Trouble Zone(s) displayed has/have not sent a checkin signal within the programmed interval (see page 23). Console Tamper The Magellan console was tampered with. Zone Tamper Zone(s) displayed was/were tampered with. Fail to Communicate with Central* The Magellan console has failed to contact the monitoring station. Fail to Communicate with Voice Reporting* The Magellan console has failed to contact telephone number programmed for Voice reporting.
WinLoad Software Settings Panel Answer Options The following two options define how Magellan answers an incoming call from a computer using the WinLoad Installer Upload/Download Software. Answering Machine Override Section [074]: 010 to 255 seconds; 000 = disabled; Default = disabled When using WinLoad to communicate remotely with an installation site that uses an answering machine or service, the answering machine override must be programmed. Using WinLoad, you will call Magellan, hang up, then call back.
Appendix 1: Automatic Report Code List System Event Default Contact ID Report Code when using sections [790] to [795] Default SIA Report Code when using sections [790] to [795] Arming with Master Code (##) 3 4A1 - Close by user CL - Closing Report Arming with User Code (##) 3 4A1 - Close by user CL - Closing Report Arming with Keyswitch (##) 3 4A9 - Keyswitch Close CS - Closing Keyswitch Auto Arming 3 4A3 - Automatic Close CA - Automatic Closing Arm with PC software 3 4A7 - Remote arm/disarm
System Event Default Contact ID Report Code when using sections [790] to [795] Default SIA Report Code when using sections [790] to [795] AC Failure 1 3A1 - AC loss AT - AC Trouble Battery Failure 1 3A9 - Battery test failure YT - System Battery Trouble Auxiliary supply trouble 1 3AA - System trouble YP - Power Supply Trouble Bell output current limit 1 321 - Bell 1 YA - Bell Fault Bell absent 1 321 - Bell 1 YA - Bell Fault Clock lost 1 626 - Time/Date inaccurate JT - Time Changed Fire
Appendix 2: Ademco Contact ID Report Code List CID# Reporting Code Programming Value Medical Alarms - 100 100 Medical alarm 01 101 Pendant transmitter 02 102 Fail to report in 03 Fire Alarms - 110 CID# Reporting Code Programming Value 154 Water leakage 29 155 Foil break 2A 156 Day trouble 2B 157 Low bottled gas level 2C 158 High temperature 2D 159 Low temperature 2E 110 Fire alarm 04 161 Loss of air flow 2F 111 Smoke 05 162 Carbon monoxide detected 30 112 Combu
CID# Reporting Code Programming Value 335 Local printer paper out 54 336 Local printer failure 55 337 Expansion module DC loss 56 338 Expansion module low battery 57 339 Expansion module reset 58 341 Expansion module tamper 59 342 Expansion module AC loss 5A 343 Expansion module self-test fail 5B 344 RF receiver jam detect 5C Communication Troubles - 350 and 360 350 Communication 5D 351 Telco 1 fault 5E 352 Telco 2 fault 5F 353 Long range radio 60 354 Fail to commu
CID# Reporting Code Programming Value 525 Reversing relay disabled AE 526 Notification appliance chk. #3 disabled AF 527 Notification appliance chk. #4 disabled B0 Modules - 530 531 Module added B1 532 Module removed B2 Communication Disables - 550 and 560 551 Dialer disabled B3 552 Radio transmitter disabled B4 Bypasses - 570 570 Zone bypass B5 571 Fire bypass B6 572 24Hr.
Index Numerics 001 to 016 ...............................................................13–16 021 to 036 .....................................................................17 058 ................................................................................17 059 ................................................................................17 060 ................................................................................13 061 .....................................................................
Arming options Auto-arm options .......................................................21 Bell Squawk on Arm/Disarm with Remote Control .........22 Closing Delinquency Timer .........................................22 Exit delay ..................................................................22 Exit Delay Termination ...............................................22 Follow Zone switches to Entry Delay 2 .........................22 No Exit Delay when Arming with Remote Control ..........
E O Entry Delay 1 ................................................................13 Entry Delay 2 ................................................................13 EOL zones ....................................................................16 Event PGM activation ..........................................................31 PGM deactivation ......................................................31 Event call direction ........................................................28 Exit Delay Termination ....
Special disarming ......................................................25 System trouble ..........................................................26 System trouble restore ...............................................26 Test ..........................................................................30 Zone alarm ................................................................25 Zone alarm restore .....................................................25 Zone tamper .........................................
System master code ..................................................12 User code length .......................................................12 V Viewing .........................................................................17 Viewing transmitter signal strength ...............................17 Voice message repetitions ............................................27 Voice message telephone numbers ..............................27 Zone programming ....................................................
Paradox Magellan Systems 45
WARRANTY Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded.
For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday from 8:00AM to 8:00PM EST. For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00AM to 8:00PM EST. Please feel free to visit our website at www.paradox.ca. 780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA Tel.: (450) 491-7444 Fax: (450) 491-7313 www.paradox.