Installation manual

Paradox Magellan Systems 25
Reporting and Dialer Settings
Report Codes
A report code is a 1- or 2-digit hexadecimal value consisting of
digits from 1 to F. Each section from [120] to [156] represents a
set of up to four specific events and each of these events can be
programmed with a separate 1- or 2-digit report code.
Only the Ademco Slow, Silent Knight, and Sescoa formats
support 1-digit report codes. To program a 1-digit report
code, press the [0] key followed by the desired hexadecimal
digit or vice versa.
When a specific event occurs, the console will attempt to
transmit the programmed report code to the monitoring station.
The method of report code transmission is defined by the
Reporting Formats (see page 28) and the Event Call Direction
(see page 28). These two items define how and where the report
codes are transmitted. If you are using the Ademco Contact ID
format, sections [120] to [156] do not have to be programmed
(see Appendix 2: Ademco Contact ID Report Code List on page
37). For more information, refer to Reporting Formats (see
page 28). The following sub-sections provide a brief description
of the events that the Magellan console can report.
Arming Report Codes
Sections [120] to [123]
A report code can be programmed for each of the 16 User
codes. When using an Access code to arm the system, the
Magellan console can send the appropriate report code to the
monitoring station, identifying which user armed the system.
Special Arming Report Codes
Sections [124] and [125]
Whenever the system is armed using one of the special arming
features listed below, the console can send the appropriate
report code to the monitoring station identifying how the system
was armed.
Section [124]
• Timed Auto-arming: The system has armed itself at the
programmed time (see page 21).
• Late to Close: Reports every day at the time specified by the
Auto-arm Timer (see page 21).
• No Movement: The system has armed itself after the
programmed period without movement (see No Movement
Auto-Arming on page 21).
• Partial Arming: The system was Stay, Instant or Force
Armed or armed with bypassed zones.
Section [125]
• One-touch Arming: The system was armed using a One-
touch Arming feature (see page 22).
• Remote Arming: The system was armed using the WinLoad
software.
Disarming Report Codes
Sections [126] to [129]
A report code can be programmed for each of the 16 User
codes. Whenever an Access code is used to disarm the system
or an alarm, the Magellan console can send the appropriate
report code to the monitoring station, identifying which user
disarmed the system.
The Disarming and the Special Disarming report codes can be
transmitted every time the system is disarmed or only when the
system is disarmed after an alarm (see Disarming Reporting
Options on page 30).
Special Disarming Report Codes
Section [130]
Whenever using one of the special disarming features, the
Magellan console can send the report code to the monitoring
station, identifying how the system was disarmed.
• Cancel Auto-arm: The system is disarmed during the Timed
Auto-arm's 60-second Exit Delay (see page 21). Only reports if
Disarming Reporting Options (see page 30) are set to always
report disarming.
• Remote Disarm: System is disarmed using the WinLoad
software.
Zone Alarm Report Codes
Sections [131] to [134]
A report code can be programmed for each of the 16 available
zones. Whenever a zone generates an alarm, the console can
send the appropriate report code to the monitoring station,
identifying which zone generated an alarm.
Zone Alarm Restore Report Codes
Sections [135] to [138]
A report code can be programmed for each of the 16 available
zones. The Magellan console can transmit these report codes to
the monitoring station identifying which zone was restored.
A zone is restored when it closes after generating an alarm or
once the bell has cut off after alarm generation. Please refer to
Zone Alarm Restore Report Codes on page 25.
Special Alarm Report Codes
Sections [139] and [140]
Whenever the system generates an alarm due to one of the
conditions listed below, the control panel can send the
appropriate report code to the monitoring station identifying the
type of alarm.
Section [139]
• Emergency Panic: Panic keys [1] and [3] (see page 24) or
the appropriate button(s) on a remote control (see page 18)
have been pressed.
• Auxiliary Panic: Panic keys [4] and [6] (see page 24) or the
appropriate button(s) on a remote control (see page 18)
have been pressed.