All-In-One Wireless Security System V1.
Table of Contents Things You Should Know ..................................... 4 About This Programming Guide........................................... Conventions ......................................................................... Installer Code (Default: 0000 / 000000) ............................... Maintenance Code (Default: 1111 / 111111) ....................... Master Code (Default: 1234 / 123456)................................. Decimal and Hexadecimal Values ..................................
Things You Should Know About This Programming Guide This programming guide should be used in conjunction with the Magellan Reference & Installation Manual which can be downloaded from our Web site at www.paradox.ca. Use this guide to record the settings programmed for this console. Conventions This symbol designates a warning or important information. This symbol designates a suggestion or reminder. This symbol designates a reference to another section, manual or guide.
Maintenance Code (Default: 1111 / 111111) The Maintenance code is similar to the Installer code. It can be used to enter programming mode (see Entering Programming Mode on page 7), which allows you to program all the features, options and commands except for the Magellan console’s communication settings (sections [100] to [154]) as well as any user codes. The Maintenance code can be 4 or 6 digits in length (see section [090] option [1] on page 12) where each digit can be any value from 0 to 9.
Decimal and Hexadecimal Values Figure 1: Decimal and Hexadecimal Values Hexadecimal only values: [1] = A [2] = B [3] = C [4] = D [5] = E [6] = F Decimal and Hexadecimal Values: Keys [0] to [9] = 0 to 9 6 Programming Guide
Entering Programming Mode Use the built-in keypad to access Magellan’s installer programming mode. To access programming mode: 1. 2. 3. 4. 5. Press and hold the [0] key. Enter your [INSTALLER CODE] or [MAINTENANCE CODE]. Enter the 3-digit [SECTION] you wish to program. Enter the required [DATA]. Press the [*] key to clear data or to go back one step. Press the [#] key to save changes.
Zone Programming Zone Definitions ( J[4] J[6] ) 000 = Zone Disabled (default) 008 = Delayed Fire Zone 001 = Entry Delay 1 009 = 24Hr. Burglary Zone 002 = Entry Delay 2 010 = 24Hr. Hold-up Zone 003 = Follow Zone 011 = 24Hr. Buzzer Zone 004 = Follow / Stay Zone 012 = 24Hr. Gas Zone 005 = Instant Zone 013 = 24Hr. Heat Zone 006 = Instant / Stay Zone 014 = 24Hr. Water Zone 007 = Instant Fire Zone 015 = 24Hr.
Wireless Transmitter Programming In the section corresponding to the desired zone, assign the transmitter’s serial number. In sections [058] and [059], assign the 6-digit serial number of the MG-DCT1 that you are using as wireless doorbells. You can also use these sections to view the assigned transmitter’s signal strength.
System Timers Section Data (value from 000 to 255) [060] ____/____/____ seconds [061] Description Defaults Entry delay 1 ( J[4] J[4] ) 045 secs. ____/____/____ seconds Entry delay 2 ( J[4] J[4] ) 045 secs. [062] ____/____/____ seconds Exit delay ( [063] ____/____/____ minutes Bell cut-off time ( [064] ____/____/____ x 15 minutes No movement time Disabled [065] ____/____/____ seconds (minimum 10 seconds) Intellizone delay 045 secs.
Section Data (value from 000 to 255) Description Defaults [080] ____/____/____ days Closing delinquency delay Disabled [081] ____/____/____ (000 to 007*) Entry delay audio selection ( [082] ____/____/____ (000 to 007*) Exit delay audio selection ( [083] Future use Future use Future use [084] ____/____:____/____ Hours Auto-test report time Disabled [085] ____/____:____/____ Hours Auto-arm time ( Disabled 003 J[4] J[4] ) 002 J[4] J[4] ) J[8] J[3] ) * 000 = No tone; 001 = Beeping;
System Options [090] General Options Option [091] ON [1] Access code length 6 digits 4 digits [2] Audible trouble warning (except AC power failures) Disabled Enabled [3] Lock master code Disabled Enabled [4] Use user code 16 as duress code Disabled Enabled [5] Console tamper supervision Disabled Enabled [6] Need code to bypass zones Disabled Enabled [7] PGM1 normal state N.O. N.C. [8] PGM2 normal state N.O. N.C.
[092] Arming/Disarming Options Bold = Default setting Option [093] ON [1] Auto-arm on time ( Disabled Enabled [2] Auto-arm on no movement Disabled Enabled [3] Auto-arm in what arming mode Regular Stay [4] Switch to Stay arming if no entry delay is opened Disabled Enabled [5] Regular arming switches to Force arming Disabled Enabled [6] Stay arming switches to Force arming Disabled Enabled [7] One-touch Regular/Force arming Disabled Enabled [8] On
[094] Zone Options Bold = Default setting Option Stay delay zones Disabled Enabled [2] Report zone restore On Bell cut-off On zone closure [3] & [4] Tamper recognition options See table See table See table See table [3] OFF OFF ON [4] OFF ON OFF ON ON - Disabled - Trouble only - Disarmed: Trouble only - Armed: Follow zone’s alarm type (page 8) - Disarmed: Audible alarm - Armed: Follow zone’s alarm type (page 8) [5] Generate tamper trouble if detected on bypassed zone N
[096] General Options Bold = Default setting Option [1] & [2] [3] & [4] [097] Magellan Doorbell 1 tone options [1] [2] OFF OFF - Tone 1 OFF ON - Tone 2 ON OFF - Tone 3 ON ON - Tone 4 Doorbell 2 tone options [3] [4] OFF OFF - Tone 1 OFF ON - Tone 2 ON OFF - Tone 3 ON ON - Tone 4 OFF ON See table See table See table See table See table See table See table See table [5] Daylight savings time Disabled Enabled [6] AC power failure warning Disab
[098] Dialer Options Bold = Default setting Option [1] & [2] [099] Telephone line monitoring options [1] [2] OFF OFF - TLM disabled OFF ON - Generate a trouble ON OFF - Generate audible alarm if armed ON ON - Silent alarms become audible ON See table See table See table See table [3] Switch to pulse on 5th attempt Disabled Enabled [4] Call back Disabled Enabled [5] Alternate dialing Disabled Enabled [6] Force dial Disabled Enabled [7] DTMF diali
[100] Event Call Direction Options for Bold = Default setting Arming / Disarming Report Codes Option OFF ON [1] Call central station telephone number 1 Disabled Enabled [2] Call central station telephone number 2 Disabled Enabled [3] Call Pager telephone number Disabled Enabled [4] Future use Future use Future use Alarm / Alarm Restore Report Codes [101] [5] Call central station telephone number 1 Disabled Enabled [6] Call central station telephone number 2
[102] Event Call Direction Options for Bold = Default setting Special Report Codes Option [103] OFF ON [1] Call central station telephone number 1 Disabled Enabled [2] Call central station telephone number 2 Disabled Enabled [3] Call Pager telephone number Disabled Enabled [4] to [8] Future use Future use Future use OFF ON Wireless Transmitter Supervision Zone Options Option [104] [1] Zone 1 supervision Disabled Enabled [2] Zone 2 supervision Disabled
[104] Wireless Transmitter Supervision Zone Options Bold = Default setting Option OFF ON [6] Zone 14 supervision Disabled Enabled [7] Zone 15 supervision Disabled Enabled [8] Zone 16 supervision Disabled Enabled Communicator Settings Section Data Description [105] ____/____/____ Report format for central station telephone number 1 ( J[4] J[3] ) [106] ____/____/____ Report format for central station telephone number 2 ( J[4] J[3] ) 001 = Ademco slow (1400Hz 10BPS); 002
Section Data [112] Description Central station telephone number 2 (32 digits maximum; if less than 32, press [#] to accept) ( J[4] J[3] ) ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___ [113] Pager Telephone # (32 digits maximum; if less than 32, press [#] to accept) ( J[4] J[3] ) ___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___/___ [114] Numeric m
Report Codes Arming Report Codes Special Arming Report Codes Disarming Report Codes Default = FF Special Disarming Report Codes Section Data Section Data Section Data Section Data [120] [121] [122] [123] Magellan ____/____ User Code 1 [124] ____/____ Auto-arming [126] ____/____ User Code 1 [130] ____/____ End auto-arm ____/____ User Code 2 ____/____ Late to close ____/____ User Code 2 ____/____ Disarm via PC ____/____ User Code 3 ____/____ No movement ____/____ User Code 3 ____/__
Alarm Report Codes Alarm Restore Report Codes Special Alarm Report Codes Default = FF Tamper Report Codes Section Data Section Data Section Data Section Data [131] [132] [133] [134] 22 ____/____ Zone 1 [135] ____/____ Zone 1 [139] ____/____ Emer. panic [141] ____/____ Zone 1 ____/____ Zone 2 ____/____ Zone 2 ____/____ Aux.
Tamper Restore Report Codes System Troubles Report Codes System Troubles Restore Report Codes Section Data Section Data Section Data [145] [146] [147] [148] ____/____ Zone 1 [149] ____/____ Future use [152] ____/____ TLM Default = FF Special Report Codes Section Data [155] ____/____ Cold start ____/____ Zone 2 ____/____ AC failure ____/____ AC failure ____/____ Test report ____/____ Zone 3 ____/____ Battery failure ____/____ Battery failure ____/____ Future use ____/____ Zone 4 ___
Remote Control Button Programming Table 1: Remote Control Button Options Hexa Description Hexa Description 0 Button disabled 8 Panic 1† 1 Regular arming 9 Panic 2† 2 Stay arming A* Panic 3† 3 Instant arming B* PGM Activation (Event Group #07. See Table on page 11) 4 Force arming C* PGM Activation (Event Group #08.
Section Data (Default: 4DE0) [166] Remote Control Buttons _______/_______/_______/_______ Remote Control 6 The button of the MG-REM1 remote control has been permanently programmed to disarm the system. The button’s functionality cannot be altered.
System Settings Section Data Description Defaults [180] ____/____/____ Installer code lock (Enter 147 to lock code, 000 to unlock code) 000 [181] ____/____/____/____/____/____ Installer code ( 000000 [182] ____/____/____/____/____/____ Maintenance code ( [200] Reset Master code to default (123456) [201] Reset all programmable sections to factory default values J[4] J[8] ) J[4] J[8] ) 111111 Installer Quick Keys To access the Installer Quick keys, press and hold the [0] key from the Main
Appendix 1: PGM Event Table Event Group # 00 = Zone closed 01 = Zone opened 02 = System status 03 = Future use 04 = Future use 05 = Non-reportable event Magellan Sub-group # 01 to 16 = Zone number 99 = Any zone number 00 = N/A 01 = N/A 02 = Silent alarm 03 = Buzzer alarm 04 = Steady alarm 05 = Pulsed alarm 06 = Strobe 07 = Alarm stopped 08 = Squawk ON 09 = Squawk OFF 10 = Ground start 11 = System disarmed 12 = System armed 13 = Entry delay engaged 99 = Any system status event Future use 00 = Telephone li
Event Group # 05 = Non-reportable event (cont’d) 06 = Remote access 07 = PGM activation (Remote control button option “B”; see page 24) 08 = PGM activation (Remote control button option “C”; see page 24) Sub-group # 06 = PC fail to communicate 07 and 08 = Future use 09 = Doorbell 1 battery trouble 10 = Doorbell 1 battery trouble restore 11 = Doorbell 2 battery trouble 12 = Doorbell 2 battery trouble restore 13 = Utility Key 1 pressed (keys [1] and [9] from the center keypad) 14 = Utility Key 2 pressed (ke
Event Group # Sub-group # 12 = Delay zone alarm transmission 01 to 16 = Zone number 99 = Any zone number 13 = Arming with user 01 to 16 = User number 99 = Any user number 14 = Special arming 00 = Auto-arming 01 = Late to close 02 = No movement arming 03 = Partial arming 04 = Quick arming 05 = Arming through WinLoad 99 = Any special arming event 15 = Disarming with user 16 = Disarm after alarm with user 17 = Alarm cancelled with user 18 = Special disarming 01 to 16 = User number 99 = Any user number
Event Group # Sub-group # 24 = Special alarm 00 = Panic emergency 01 = Panic medical 02 = Panic fire 03 = Recent closing 04 = Global shutdown 24 = Special alarm (cont’d) 05 = Duress alarm (User 16) 99 = Any special alarm event 25 = Zone shutdown 26 = Zone tampered 27 = Zone tamper restore 01 to 16 = Zone number 99 = Any zone number 28 = New trouble 00 = N/A 01 = AC failure 02 = Battery failure 03 = Clock loss 04 = Console tamper 05 = Fail to communicate to central 06 = Fail to communicate to voice
Event Group # 29 = Trouble restored (cont’d) Sub-group # 07 = N/A 08 = RF interference restore 99 = Any trouble restore event 30 = Low battery on zone 31 = Low battery on zone restore 32 = Zone supervision trouble 01 to 16 = Zone number 99 = Any zone number 33 = Zone supervision restored 34 = Special 00 = System power up 01 = Reporting test 02 = WinLoad logon 03 = WinLoad logoff 04 = Installer in programming mode 05 = Installer exited programming mode 06 = Closing delinquency delay elapsed 99 = Any spe
Event Group # Sub-group # 43 = Future use Future use 44 = Future use Future use 45 = Future use Future use 46 = Future use Future use 47 = Future use Future use 48 = Fire delay started 01 to 16 = Zone number 99 = Any zone number 49 = Fire delay cancelled 32 Programming Guide
Appendix 2: Connection Diagrams Power Connections Figure 2: Connecting the Transformer Back view of the Magellan console. Do not use any switch-controlled outlets. 16Vac 20VA transformer Insert the transformer’s wires into the AC terminals.
Figure 3: Connecting the Battery 1. Insert the backup battery’s plug into the connector labelled BATT. Partial view of the backside of the Magellan console. Battery compartment 2. Slide in the battery pack horizontally, tilt the battery pack downward and then tuck it in Magellan’s battery compartment. 3. After inserting the battery pack’s plug, tuck the cables in the specially designed slot. To order a battery pack, the battery pack’s part number is: Paradox #0780100178. 34 4.
Telephone Line Connections Figure 4: Telephone Line Direct Connect Telephone Line Connection Note The Magellan console must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephones, answering machines, computer modems, etc.) already has the line in use.
Figure 5: Line Plug Connection Do not connect the RJ-11 cable into this plug. Back view of the Magellan console. To connect the telephone line directly to the console: 1. Insert one end of the 4-pin RJ-11 cable into the line plug of the Magellan console. 2. Insert the other end of the RJ-11 cable into a standard telephone wall plug.
PGM Connections Figure 6: PGM Connections Method 1 (< 100mA) Back view of the Magellan console. External Power Supply Devices such as a light, etc. Method 2 (> 100mA) If the PGM current consumption is less than 100mA, use method 1. If the PGM current consumption is to exceed 100mA, use method 2. Do not exceed 24Vdc when connecting the PGM outputs. External relay Devices such as a light, etc.
Hardwire Zone Connections Figure 7: Hardwire Zone Connections Back view of the Magellan console.
X10 Transmitter Connections Figure 8: Connecting the X10 Transmitter Back view of the Magellan console. 1. Connect one end of the inverted 4-pin RJ-11 cable into the X10 plug of the console. 2. Connect the other end of the inverted 4-pin RJ-11 cable into the X10 transmitter. 3. Plug the X10 transmitter into a standard wall outlet. For information on programming the X10 features of Magellan, refer to the X10 Operation User Guide which can be found and downloaded for free from our Web site at www.paradox.ca.
Connecting Magellan to WinLoad Figure 9: Connecting Magellan to WinLoad Back view of the Magellan console.
Connecting to a UIP-256 Figure 10: Connecting to a UIP-256 Universal In-Field Programmer Back view of the Magellan console. Connect the 10pin cable of the UIP-256 to the 10pin connector of the Magellan console UIP-256 Universal In-Field Programmer Standard DB-9 cable (9-pin serial cable) Download latest firmware version of Magellan from the Paradox Web site at www.paradox.
Connecting a Paradox Memory Key (PMC-3) Figure 11: Connecting a Paradox Memory Key (PMC-3) PMC-3 Jumper ON: Read from and/or write to memory key Jumper OFF: Write protected (Read from the memory key only) Back view of the Magellan console.
Connecting the Radio Antenna Figure 12: Connecting the Radio Antenna Back view of the Magellan console. If the radio reception is not very good, connect the supplied radio antenna to the ANT terminal of the Magellan console. Move the antenna around until the spot with the best reception is found.
Mounting Magellan on the Wall Figure 13: Mounting Magellan onto the Wall Plate To mount the wall plate: 1. Place the wall plate on the desired spot of the wall. 2. Drill and insert the screws into the holes labeled A at left. To mount the Magellan console: 1. 2. 3. 4. Place the console back plate flush against the mounted wall plate. Slide the Magellan’s open slots labeled D (see Inset 1 below) onto the wall plate’s tabs labeled B.
Tabletop Mounting Figure 14: Tabletop Mounting Plastic feet (x2) To mount the Magellan console on a tabletop the wall plate has to be inserted beforehand: 1. Slide the wall plate’s tabs labeled B into the Magellan console’s open slots labeled D (see Figure 13 on page 44). 2. Insert two screws (included) through the wall plate’s screw holes labeled C into holes labeled E in the Magellan console (see Figure 13 on page 44). 3.
Appendix 3: Ademco Contact ID Report Code List CID# Reporting Code Programming Value Medical Alarms - 100 100 CID# 125 Reporting Code Duress - Egress granted Programming Value 12 147 Reporting Code Sensor supervision failure Programming Value 24 Medical alarm 01 101 Pendant transmitter 02 130 Burglary 13 150 24-hour non-burglary 25 102 Fail to report in 03 131 Perimeter 14 151 Gas detected 26 27 Fire Alarms - 110 Burglar Alarms - 130 CID# 24-hour Non-burglary - 150 and 160
CID# Reporting Code Programming Value CID# Reporting Code Programming Value CID# Reporting Code Programming Value 204 Low water level 36 322 Bell 2 49 205 Pump activated 37 323 Alarm relay 4A 350 Communication 5D 206 Pump failure 38 324 Trouble relay 4B 351 Telco 1 fault 5E System Troubles - 300 and 310 Communication Troubles - 350 and 360 325 Reversing relay 4C 352 Telco 2 fault 5F 300 System trouble 39 326 Notification appliance chk.
CID# Reporting Code Programming Value CID# Reporting Code Programming Value CID# Reporting Code Programming Value 381 Loss of supervision - RF 6F 407 Remote arm/disarm 80 430 Access program mode exit 92 382 Loss of supervision - RPM 70 408 Quick arm 81 431 Access threat level change 93 383 Sensor tamper 71 409 Keyswitch open/close 82 432 Access relay/trigger fail 94 384 RF transmitter low battery 72 433 Access RTE shunt 95 385 Smoke detector Hi sensitivity 73 411
CID# Reporting Code Programming Value CID# Reporting Code Programming Value Reporting Code Programming Value 462 Legal code entry A4 612 Point not tested C7 463 Re-arm after alarm A5 570 Zone bypass B5 613 Intrusion zone walk tested C8 464 Auto-arm time extended A6 571 Fire bypass B6 614 Fire zone walk tested C9 465 Panic alarm reset A7 572 24Hr.
Warranty Paradox Security Systems Ltd. ("Seller") warrants its products to be free from manufacturing defects in materials and workmanship for one-year following the date of manufacture. Seller will, within this period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
Installer Menu Overview ready to arm menu 1-bypass zones 2-alarm clock 3-time and date 4-system setup Must enter the installer, maintenance or user code to access 1-language 2-user profile† 3-communicator central report? voice report? utility report? add tel. # 1 add tel. # 1 add tel. # 1 add backup # add tel. # 2 add tel.
