Use and Care Manual

ManualsBrandsMagic Home ManualsFurniture113.4 in. Flared Arm Teddy Velvet 4-Wide Seats Tufted Rectangle Sectional Sofa Couch with Ottoman, Orange

Installation

Hardware List

Seat

Backrest

Right armrest

8x25mm screws

Nuts、

Washers、long screws

Legs

Support rods

Iron sheets

Install the support rods as shown in picture 1

Backrest

8x25mm screw

Insert the backrest into the seat

cushion, notice the short lock

buckles facing forward, and then

fasten the lock buckles to the ring of

the seat cushion according to the

diagram. (If the rope is not long

enough, don’t worry, this is not a

quality problem, it’s for the solidness

after the installation of the lock

buckles. When this happens you

need to press the backrest and the

seat cushion down, the lock can be

easily buckled)

Summary of content (6 pages)

PAGE 1
Installation Hardware List 2 Hardware List 1 Backrest 1 Seat 1 Right armrest Nuts、 4 8x25mm screws Legs 16 5 Washers、long screws 2 Support rods 1 2 Iron sheets Backrest 8x25mm screw Install the support rods as shown in picture 1 1 Insert the backrest into the seat cushion, notice the short lock buckles facing forward, and then fasten the lock buckles to the ring of the seat cushion according to the diagram.
PAGE 2
3 Turn over the seat, install the feet and fasten support rods. 1 4 Install the armrests. Please refer to step 2 2 1-4 steps: insert the long screws into the backrest support rod, about 7-8 mm deep, and let the rest of the screw go through the iron sheet, then apply 8x25mm screws to fix 4 predrilled holes about half way, when all the screws are in place with the holes, tighten them completely. Tip: If holes and screws do not match, try to adjust them adjustable space has been reserved.
PAGE 3
Installation Hardware List 2 Hardware List 1 Backrest 1 Seat 1 Left armrest Nuts、 4 8x25mm screws Legs 16 5 Washers、long screws 2 Support rods 1 2 Iron sheets Backrest 8x25mm screw Install the support rods as shown in picture 1 1 Insert the backrest into the seat cushion, notice the short lock buckles facing forward, and then fasten the lock buckles to the ring of the seat cushion according to the diagram.
PAGE 4
3 Turn over the seat, install the feet and fasten support rods. 1 4 Install the armrests. Please refer to step 2 2 1-4 steps: insert the long screws into the backrest support rod, about 7-8 mm deep, and let the rest of the screw go through the iron sheet, then apply 8x25mm screws to fix 4 predrilled holes about half way, when all the screws are in place with the holes, tighten them completely. Tip: If holes and screws do not match, try to adjust them adjustable space has been reserved.
PAGE 5
Installation Hardware List 2 Hardware List 1 Backrest 1 Seat 1 8x25mm screws 16 Ottoman Nuts、 4 Legs 10 Washers、long screws 2 Support rods 1 2 Iron sheets Backrest 8x25mm screw Install the support rods as shown in picture 1 1 Insert the backrest into the seat cushion, notice the short lock buckles facing forward, and then fasten the lock buckles to the ring of the seat cushion according to the diagram.
PAGE 6
3 Turn over the seat, install the feet and fasten support rods. 1 4 Finished. 2 1-4 steps: insert the long screws into the backrest support rod, about 7-8 mm deep, and let the rest of the screw go through the iron sheet, then apply 8x25mm screws to fix 4 predrilled holes about half way, when all the screws are in place with the holes, tighten them completely. Tip: If holes and screws do not match, try to adjust them adjustable space has been reserved.