Installation Instructions

EUROSTONE VANITY WITH TOP
INSTALLATION INSTRUCTIONS
Questions? Call our customer service department at 1-855-995-5578, 8:30 a.m. - 5 p.m., CST, Monday - Friday
or e-mail: [e-mail].
Tools required for assembly (not included):
• pliers (A)
• tape measure
• electric drill with #2 drill bit (B)
• level
• (x 2) #8 x 2” screws (C)
• (x 2) wall anchors - if the vanity will not be
screwed to wall studs (D)
• silicone (optional) (E)
Estimated installation time: 2-1/2 hours
(including removal of old vanity if applicable)
PREPARATION
PACKAGE CONTENTS
OVERALL DIMENSIONS (INCLUDING TOP):
24” W x 33-3/4” H x 17-1/8” D
60.96 cm W x 85.72 cm H x 43.5 cm D
Faucet and drain not included.
Top (x 1)
Knobs (x 2)
1” screws (x 2)
INSTALLATION
1: Removing old vanity (if applicable): 1) Turn
off the water supply and take the drain out.
2) Disconnect the supply lines from the faucet.
3) Remove the old vanity top and vanity.
If the new vanity is not installed immediately,
temporarily stuff a rag into the drain pipe.
2: Using a level, locate any uneven oor
and/or wall areas where your vanity will be
installed. Unevenness can cause your vanity
to become misaligned resulting in twisting of the
cabinet. Repair any uneven areas by reducing high
spots or shimming low spots.
3: Provide sufcient protection on the oor to protect
the vanity from damage. Tilt the vanity backwards and
remove the shipping feet from the bottom of the vanity base using a pair of pliers (A - not included). Figure 1.
4: 1) Place the vanity in the desired position taking into account the location of your plumbing. 2) Ensure the vanity is level front to back
and at both sides.
5: Secure the vanity to the wall by inserting (x 2) #8 x 2” screws (C - not included) through the back rail of the vanity. Figure 2. It is
recommended that the vanity be installed to at least one wall stud. If you are unable to locate wall studs, it is recommended that you
use wall anchors (D - not included) to secure the vanity.
6: Attach the (x 2) knobs by using (x 2) 1” screws. Figure 3.
7: Place the vanity top centered on the vanity base. Figure 4. For additional stability, clear silicone (E - not included) may be used to
secure the vanity top onto the vanity base.
8: Connect the faucet and drain (both not included) as per the instruction sheets provided with those items and ensure that there is no leakage.
Figure 2Figure 1
WARNINGS & CAUTIONS CARE & MAINTENANCE
WARNING:
Two people are required for safe installation. Take extra
precautionary measures to ensure a secure grip on the vanity
base and top when lifting.
CAUTION:
• The bathroom oor and wall must be nished prior to
installation of the vanity and vanity top.
• Do not use water that exceeds temperatures of 140°F/46°C.
• Do not place any sharp or abrasive objects on the bare surface
of the vanity top.
• To maintain the beauty of the furniture nish, avoid placing the
vanity in direct sunlight.
• Avoid exposing the vanity to extreme temperatures by installing
away from heat and air vents.
• Dust frequently with a clean, soft and dry cloth.
• Wipe away any water or liquid spills on the vanity base
immediately with a clean, soft and dry cloth.
• Clean the vanity top only with non-abrasive cleaners or mild
detergents - do not use powder cleansers. For extremely
stubborn stains, use a small amount of acetone on a cloth
and gently rub out the stain.
Base (x 1)
Bumpers (x 4)
Matte white model: 30695
Gray model: 30696